Standard Test Method for Shear Strength of Plastics by Punch Tool

Available format(s)

PDF

Language(s)

English

Published date

01-05-2017

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 08.01, 2017 Describes the procedure for determining the shear strength of composite materials in the form of sheets, plates, and molded shapes in thicknesses from 1.27 to 12.7 mm (0.050 to 0.500 in.).

1.1This test method covers the procedure for determining the shear strength of plastics in the form of sheets, plates, and molded shapes in thicknesses from 1.27 to 12.7 mm (0.050 to 0.500 in.).

1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1:There is no known ISO equivalent to this standard.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	D 20
DocumentType	Redline
Pages	5
PublisherName	American Society for Testing and Materials
Status	Current

DOD-STD-35-24 Revision A:1978	AUTOMATED ENGINEERING DOCUMENT PREPARATION SYSTEM, BEARINGS
15/30321951 DC : 0	BS ISO 20195 - STANDARD PRACTICE - GUIDE FOR DESIGN FOR ADDITIVE MANUFACTURING
ASTM D 7745 : 2019 : REDLINE	Standard Practice for Testing Pultruded Composites
MIL-P-46179 Revision A:1986	PLASTIC MOLDING AND EXTRUSION MATERIAL, POLYAMIDE IMIDE
MIL-P-46847 Revision B:1984	PLASTIC MATERIAL, FOAMED POLYURETHANE FOR ENCAPSULATING ELECTRONIC COMPONENTS
AASHTO LRFDLTS 1 : 1900	LRFD SPECIFICATIONS FOR STRUCTURAL SUPPORTS FOR HIGHWAY SIGNS, LUMINAIRES, AND TRAFFIC SIGNALS
BS ISO 12891-2:2014	Retrieval and analysis of surgical implants Analysis of retrieved surgical implants
MIL S 24154 : A	SYNTACTIC BUOYANCY MATERIAL FOR HIGH HYDROSTATIC PRESSURES
ASTM F 755 : 1999 : R2005	Standard Specification for Selection of Porous Polyethylene for Use in Surgical Implants
ACI 560R : 2016	REPORT ON DESIGN AND CONSTRUCTION WITH INSULATING CONCRETE FORMS (ICFS)
ISO 12891-2:2014	Retrieval and analysis of surgical implants Part 2: Analysis of retrieved surgical implants
ASTM F 561 : 2013	Standard Practice for Retrieval and Analysis of Medical Devices, and Associated Tissues and Fluids
10/30191247 DC : DRAFT APR 2010	BS EN ISO 13628-16 - PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 16: SPECIFICATION FOR FLEXIBLE PIPE ANCILLARY EQUIPMENT
AWWA D121 : 2014	BOLTED ABOVEGROUND THERMOSETTING FIBERGLASS-REINFORCED PLASTIC PANEL-TYPE TANKS FOR WATER STORAGE
MIL-DTL-32265 Base Document:2007	Folded Fiberglass Mat Fabrication and Packaging
ASTM F 755:1999	Standard Specification for Selection of Porous Polyethylene for Use in Surgical Implants
CSA S806: 2012	DESIGN AND CONSTRUCTION OF BUILDING STRUCTURES WITH FIBRE-REINFORCED POLYMERS
S806-12 (R2017)	Design and construction of building structures with fibre-reinforced polymers
ASTM E 2634 : 2017-06	SPECIFICATION FOR FLAT WALL INSULATING CONCRETE FORM (ICF) SYSTEMS
IEEE 1133-1988	IEEE Application Guide for Evaluating Nonceramic Materials for High-Voltage Outdoor Applications
MIL-C-24449 Revision A:1981	CAST POLYMETHYL METHACRYLATE FOR SHEET STOCK, CUSTOM CASTINGS AND FINISHED WINDOWS
13/30242622 DC : 0	BS ISO 12891-2 - RETRIEVAL AND ANALYSIS OF SURGICAL IMPLANTS - PART 2: ANALYSIS OF RETRIEVED SURGICAL IMPLANTS
ASTM E 1420 : 1991	Practice for Specifying Polymeric Materials for Service in Ionizing Radiation Environments (Withdrawn 1996)
ASTM F 755 : 1999 : EDT 1	Standard Specification for Selection of Porous Polyethylene for Use in Surgical Implants
MIL-P-47099 Revision A:1989	POLYURETHANE FOAM, POLYETHER TYPE, RIGID, FOR PACKAGING AND ENCAPSULATION OF ELECTRONIC COMPONENTS
API 17L1 : 2013	SPECIFICATION FOR FLEXIBLE PIPE ANCILLARY EQUIPMENT
ASTM F 755 : 1999 : R2011	Standard Specification for Selection of Porous Polyethylene for Use in Surgical Implants
ASME PVHO 1 : 2016	SAFETY STANDARD FOR PRESSURE VESSELS FOR HUMAN OCCUPANCY

ASTM D 618 : 2013 : REDLINE	Standard Practice for Conditioning Plastics for Testing
ASTM D 4000 : 2016 : REDLINE	Standard Classification System for Specifying Plastic Materials

View more information

$108.03

Including GST where applicable

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

Log into your Account

ASTM D 732 : 2017 : REDLINE

Current

Abstract

Scope

General Product Information

Standards Referenced By This Book

Standards Referencing This Book

Category

Subcategory

Access your standards online with a subscription