Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 7552 : 2009 : R2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Determining the Complex Shear Modulus (G*) Of Bituminous Mixtures Using Dynamic Shear Rheometer
Available format(s)

Hardcopy , PDF

Superseded date

14-01-2023

Language(s)

English

Published date

07-11-2014

CONTAINED IN VOL. 04.03, 2015 Defines the determination of the complex shear modulus of bituminous mixtures using torsion rectangular geometry on a dynamic shear rheometer (DSR).

1.1This test method covers the determination of the complex shear modulus of bituminous mixtures using torsion rectangular geometry on a dynamic shear rheometer (DSR). It is applicable to bituminous mixtures having complex shear modulus values greater than 1 × 104 Pa when tested over a range of temperatures from 10°C to 76°C at frequencies of 0.01 to 25 Hz and strains of 0.001 % to 0.1 %. The determination of complex shear modulus is typically determined at 20°C to 70°C at 0.01% strain at 10 discrete frequency values covering 0.01 to 10 Hz. From these data, temperature or frequency master curves can be generated as required. This test method is intended for determining the complex shear modulus of bituminous mixtures as required for specification testing or quality control of bituminous mixture production.

1.2This test method is appropriate for laboratory prepared and compacted mixtures, field produced and laboratory compacted mixtures or field cores, regardless of binder type or grade and regardless of whether RAP is used in the mixture. Due to the geometry of the specimens being tested this test method is not applicable to open-graded or SMA mixtures. It has been found to be appropriate for dense-graded mixtures, whether coarse- or fine-graded, with 19 mm or smaller nominal maximum aggregate size.

1.3The between-laboratory reproducibility of this test method is being determined and will be available on or before June 2012. Therefore, this test method should not be used for acceptance or rejection of materials for purchasing purposes.

1.4The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 04
DocumentType
Test Method
Pages
11
ProductNote
Reconfirmed 2014
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 6925 : 2008 Standard Test Method for Preparation and Determination of the Relative Density of Hot Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor
ASTM D 6926 : 2016 : REDLINE Standard Practice for Preparation of Asphalt Mixture Specimens Using Marshall Apparatus
ASTM E 563 : 1997 Standard Practice for Preparation and Use of an Ice-Point Bath as a Reference Temperature
ASTM D 3666 : 2013 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2011 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 2726 : 2005 Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures
ASTM D 3666 : 2007 : REV A Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
DIN 43760:1987-09 MEASUREMENT AND CONTROL - ELECTRICAL TEMPERATURE SENSORS - REFERENCES-TABLES FOR NICKEL RESISTORS FOR RESISTANCE THERMOMETERS
ASTM D 2726 : 2004 Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures
ASTM D 6925 : 2007 Standard Test Method for Preparation and Determination of the Relative Density of Hot Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor
ASTM D 6926 : 2004 Standard Practice for Preparation of Bituminous Specimens Using Marshall Apparatus
ASTM D 2726 : 2010 Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures
ASTM D 3666 : 2016 : REDLINE Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 6925 : 2015 : REDLINE Standard Test Method for Preparation and Determination of the Relative Density of Asphalt Mix Specimens by Means of the Superpave Gyratory Compactor
ASTM D 2041 : 2000 Standard Test Method for Theoretical Maximum Specific Gravity and Density of Bituminous Paving Mixtures
ASTM D 3203 : 1994 : R2000 Standard Test Method for Percent Air Voids in Compacted Dense and Open Bituminous Paving Mixtures
ASTM D 6752 : 2003 : EDT 1 Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Automatic Vacuum Sealing Method
ASTM D 3666 : 2009 : REV A Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 7175 : 2005 Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer
ASTM E 644 : 2011 : REDLINE Standard Test Methods for Testing Industrial Resistance Thermometers
ASTM D 6857 : 2003 Standard Test Method for Maximum Specific Gravity and Density of Bituminous Paving Mixtures Using Automatic Vacuum Sealing Method
ASTM D 7312 : 2007 Standard Test Method for Determining the Permanent Shear Strain and Complex Shear Modulus of Asphalt Mixtures Using the Superpave Shear Tester (SST)
ASTM D 2041 : 2003 : REV A Standard Test Method for Theoretical Maximum Specific Gravity and Density of Bituminous Paving Mixtures
ASTM E 77 : 2014 : EDT 1 Standard Test Method for Inspection and Verification of Thermometers
ASTM D 7175 : 2007 Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer
ASTM D 7175 : 2005 : EDT 1 Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer
ASTM D 3203 : 2022 Standard Test Method for Percent Air Voids in Compacted Asphalt Mixtures
ASTM E 563 : 2022 Standard Practice for Preparation and Use of an Ice-Point Bath as a Reference Temperature
ASTM D 7312 : 2010 Standard Test Method for Determining the Permanent Shear Strain and Complex Shear Modulus of Asphalt Mixtures Using the Superpave Shear Tester (SST) (Withdrawn 2019)
ASTM D 6752 : 2002 : REV A Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Automatic Vacuum Sealing Method
ASTM D 7175 : 2015 : REDLINE Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer
ASTM D 3666 : 2005 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 2726 : 2000 Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures
ASTM D 3666 : 2003 : REV A Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 2041 : 2003 Standard Test Method for Theoretical Maximum Specific Gravity and Density of Bituminous Paving Mixtures
ASTM D 6925 : 2015 Standard Test Method for Preparation and Determination of the Relative Density of Asphalt Mix Specimens by Means of the Superpave Gyratory Compactor
ASTM D 3666 : 2000 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 6752 : 2003 Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Automatic Vacuum Sealing Method
ASTM D 6752 : 2002 Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Automatic Vacuum Sealing Method
ASTM D 7175 : 2008 Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer
ASTM D 6925 : 2006 Standard Test Method for Preparation and Determination of the Relative Density of Hot Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor
ASTM D 6926 : 2020 Standard Practice for Preparation of Asphalt Mixture Specimens Using Marshall Apparatus
ASTM D 2726 : 2008 Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures
ASTM D 6926 : 2010 Standard Practice for Preparation of Bituminous Specimens Using Marshall Apparatus
ASTM D 3666 : 2007 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2007 : EDT 2 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3203 : 2005 Standard Test Method for Percent Air Voids in Compacted Dense and Open Bituminous Paving Mixtures
ASTM E 563 : 2011 : R2016 Standard Practice for Preparation and Use of an Ice-Point Bath as a Reference Temperature
ASTM D 3666 : 2016 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2003 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 2726 : 2009 Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures
ASTM D 3666 : 2001 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 6925 : 2009 Standard Test Method for Preparation and Determination of the Relative Density of Hot Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor
ASTM D 7175 : 2015 Standard Test Method for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer
ASTM D 2726 : 2005 : REV A Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures
ASTM D 3666 : 2006 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 6926 : 2016 Standard Practice for Preparation of Asphalt Mixture Specimens Using Marshall Apparatus
ASTM C 670 : 2015 : REDLINE Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials
ASTM D 6925 : 2003 Standard Test Method for Preparation and Determination of the Relative Density of Hot Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor
ASTM D 3666 : 2004 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 6857 : 2009 Standard Test Method for Maximum Specific Gravity and Density of Bituminous Paving Mixtures Using Automatic Vacuum Sealing Method
ASTM E 77 : 1998 Standard Test Method for Inspection and Verification of Thermometers
ASTM D 3666 : 2005 : REV A Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM E 77 : 2014 : R2021 Standard Test Method for Inspection and Verification of Thermometers
ASTM D 3666 : 2007 : REV A : EDT 1 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 3666 : 2009 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 6752 : 2009 Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Automatic Vacuum Sealing Method
ASTM D 3666 : 2002 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
ASTM D 2726 : 2011 Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures

View more information
$135.86
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more