Customer Support: 131 242

i2i Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search

ASTM D 7564/D7564M : 2016

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Construction of Asphalt-Rubber Cape Seal
Available format(s)

Hardcopy , PDF

Superseded date

17-12-2023

Language(s)

English

Published date

11-05-2016

Publisher

American Society for Testing and Materials

1.1This practice covers asphalt-rubber cape seal, which is defined as the application of an asphalt-rubber seal coat placed onto an existing pavement surface, followed by the application of a conventional Type II or III slurry seal.

Note 1:An asphalt-rubber seal coat is also known as a stress absorbing membrane (SAM) which consists of an asphalt-rubber membrane seal followed by the application of precoated aggregate chips.

1.2An asphalt-rubber cape seal is commonly used to extend the service life of low to medium trafficked and moderately distressed asphalt-surfaced pavements. The existing pavement condition can be used to determine the application rates for the asphalt-rubber binder and aggregate as well as the aggregate gradation. Pavements in relatively poor condition will require a coarser aggregate with a higher binder application rate.

1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 04
DocumentType
Standard Practice
Pages
7
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 8418 : 2021 Standard Guide for Material and Construction Standards Related to Sustainability Within Committee D04

ASTM D 6373 : 2013 Standard Specification for Performance Graded Asphalt Binder
ASTM D 2196 : 2015 Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational Viscometer
ASTM D 3910 : 2011 Standard Practices for Design, Testing, and Construction of Slurry Seal
ASTM D 4791 : 2010 Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate (Withdrawn 2019)
ASTM D 4791 : 1999 Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate
ASTM D 6433 : 2011 Standard Practice for Roads and Parking Lots Pavement Condition Index Surveys
ASTM C 117 : 2017 Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing
ASTM D 2196 : 2010 Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational (Brookfield type) Viscometer
ASTM D 3381 : 2005 Standard Specification for Viscosity-Graded Asphalt Cement for Use in Pavement Construction
ASTM D 6433 : 2016 Standard Practice for Roads and Parking Lots Pavement Condition Index Surveys
ASTM D 6114 : 1997 : R2002 Standard Specification for Asphalt-Rubber Binder
ASTM D 5360 : 1998 Standard Practice for Design and Construction of Bituminous Surface Treatments
ASTM D 2196 : 2005 Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational (Brookfield type) Viscometer
ASTM D 5821 : 2013 : R2017 Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate
ASTM D 6373 : 1999 Standard Specification for Performance Graded Asphalt Binder
ASTM D 6373 : 2023 Standard Specification for Performance-Graded Asphalt Binder
ASTM D 6373 : 2016 Standard Specification for Performance Graded Asphalt Binder
ASTM D 6433 : 2003 Standard Practice for Roads and Parking Lots Pavement Condition Index Surveys
ASTM D 1139 : 2000 : R2004 Standard Specification for Aggregate for Single or Multiple Bituminous Surface Treatments
ASTM D 3910 : 1998 Standard Practices for Design, Testing, and Construction of Slurry Seal
ASTM D 4791 : 2005 : EDT 1 Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate
ASTM C 29/C29M : 2017 : REV A Standard Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate
ASTM D 6433 : 2018 Standard Practice for Roads and Parking Lots Pavement Condition Index Surveys
ASTM D 4791 : 2019 : R2023 Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate
ASTM D 6433 : 2023 Standard Practice for Roads and Parking Lots Pavement Condition Index Surveys
ASTM D 6114 : 1997 : EDT 1 Standard Specification for Asphalt-Rubber Binder
ASTM D 5821 : 2001 Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate
ASTM D 5821 : 2001 : R2006 Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate
ASTM D 4791 : 2019 Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate
ASTM D 6373 : 2021 : REV A Standard Specification for Performance-Graded Asphalt Binder
ASTM D 2196 : 2018 Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational Viscountess
ASTM D 4791 : 2005 Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Particles in Coarse Aggregate
ASTM D 6433 : 2020 Standard Practice for Roads and Parking Lots Pavement Condition Index Surveys
ASTM D 5360 : 2005 Standard Practice for Design and Construction of Bituminous Surface Treatments
ASTM D 1139 : 2000 Standard Specification for Aggregate for Single or Multiple Bituminous Surface Treatments
ASTM C 117 : 2023 Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing
ASTM D 3910 : 2015 Standard Practices for Design, Testing, and Construction of Slurry Seal
ASTM C 128 : 2015 Standard Test Method for Relative Density (Specific Gravity) and Absorption of Fine Aggregate
ASTM D 5360 : 2009 Standard Practice for Design and Construction of Bituminous Surface Treatments
ASTM D 2419 : 1995 Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate
ASTM D 5360 : 2015 Standard Practice for Design and Construction of Bituminous Surface Treatments
ASTM D 3910 : 2021 Standard Practices for Design, Testing, and Construction of Slurry Seal
ASTM D 2419 : 2009 Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate
ASTM C 29/C29M : 2023 Standard Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate
ASTM D 3910 : 2007 Standard Practices for Design, Testing, and Construction of Slurry Seal
ASTM D 3381 : 2009 Standard Specification for Viscosity-Graded Asphalt Cement for Use in Pavement Construction
ASTM D 6373 : 2007 : EDT 1 Standard Specification for Performance Graded Asphalt Binder
ASTM D 6433 : 2007 Standard Practice for Roads and Parking Lots Pavement Condition Index Surveys
ASTM D 6433 : 1999 Standard Practice for Roads and Parking Lots Pavement Condition Index Surveys
ASTM D 6373 : 2015 Standard Specification for Performance Graded Asphalt Binder
ASTM D 6373 : 2021 Standard Specification for Performance-Graded Asphalt Binder
ASTM C 136 : 1996 Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
ASTM D 2196 : 2018 : EDT 1 Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational Viscometer
ASTM D 5821 : 2013 Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate
ASTM D 5821 : 1995 Standard Test Method for Determining the Percentage of Fractured Particles in Coarse Aggregate
ASTM D 2196 : 1999 Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational (Brookfield type) Viscometer
ASTM D 6373 : 2007 Standard Specification for Performance Graded Asphalt Binder
ASTM D 3381 : 1992 : R1999 Standard Specification for Viscosity-Graded Asphalt Cement for Use in Pavement Construction
ASTM D 2419 : 2002 Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate
ASTM D 6433 : 2009 Standard Practice for Roads and Parking Lots Pavement Condition Index Surveys
ASTM D 2419 : 2022 Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate
ASTM D 2419 : 2014 Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate
ASTM C 128 : 2022 Standard Test Method for Relative Density (Specific Gravity) and Absorption of Fine Aggregate

View more information
$122.77
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more