ASTM D 7981 : 2015
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Practice for Compaction of Prismatic Asphalt Specimens by Means of the Shear Box Compactor
Available format(s)
Hardcopy , PDF
Superseded date
09-06-2020
Language(s)
English
Published date
01-08-2015
CONTAINED IN VOL. 04.03, 2015 Defines the fabrication of prismatic specimens of asphalt mixture using the Shear Box Compactor (SBC).
1.1This practice covers the fabrication of prismatic specimens of asphalt mixture using the Shear Box Compactor (SBC). Compacted specimens are suitable for volumetric and physical property testing. This standard practice should not be used for acceptance or rejection of a material or for purchasing purposes.
1.2Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard with exception of degrees (°) where angle is specified.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
| Committee |
D 04
|
| DocumentType |
Standard Practice
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
| ASTM D 8237 : 2018 | Standard Test Method for Determining Fatigue Failure of Asphalt-Aggregate Mixtures With the Four-Point Beam Fatigue Device |
| ASTM D 6925 : 2008 | Standard Test Method for Preparation and Determination of the Relative Density of Hot Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor |
| ASTM D 3666 : 2013 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2011 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 2726 : 2005 | Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures |
| ASTM D 3666 : 2007 : REV A | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| AASHTO T 321 : 2014 | METHOD OF TEST FOR DETERMINING THE FATIGUE LIFE OF COMPACTED ASPHALT MIXTURES SUBJECTED TO REPEATED FLEXURAL BENDING |
| ASTM D 2726 : 2004 | Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures |
| ASTM D 6925 : 2007 | Standard Test Method for Preparation and Determination of the Relative Density of Hot Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor |
| ASTM D 2726 : 2010 | Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures |
| ASTM D 3666 : 2016 : REDLINE | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 6925 : 2015 : REDLINE | Standard Test Method for Preparation and Determination of the Relative Density of Asphalt Mix Specimens by Means of the Superpave Gyratory Compactor |
| ASTM D 2041 : 2000 | Standard Test Method for Theoretical Maximum Specific Gravity and Density of Bituminous Paving Mixtures |
| ASTM D 1188 : 2007 : EDT 1 | Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Coated Samples |
| ASTM D 6752 : 2003 : EDT 1 | Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Automatic Vacuum Sealing Method |
| ASTM D 3666 : 2009 : REV A | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM E 644 : 2011 : REDLINE | Standard Test Methods for Testing Industrial Resistance Thermometers |
| ASTM D 6857 : 2003 | Standard Test Method for Maximum Specific Gravity and Density of Bituminous Paving Mixtures Using Automatic Vacuum Sealing Method |
| ASTM D 1188 : 2007 | Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Coated Samples |
| ASTM D 2041 : 2003 : REV A | Standard Test Method for Theoretical Maximum Specific Gravity and Density of Bituminous Paving Mixtures |
| ASTM D 1188 : 2007 : R2015 | Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Coated Samples |
| ASTM D 6752 : 2002 : REV A | Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Automatic Vacuum Sealing Method |
| ASTM D 3666 : 2005 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 2726 : 2000 | Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures |
| ASTM D 3666 : 2003 : REV A | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 2041 : 2003 | Standard Test Method for Theoretical Maximum Specific Gravity and Density of Bituminous Paving Mixtures |
| ASTM D 1188 : 1996 : R2002 : EDT 1 | Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Paraffin-Coated Specimens |
| ASTM D 6925 : 2015 | Standard Test Method for Preparation and Determination of the Relative Density of Asphalt Mix Specimens by Means of the Superpave Gyratory Compactor |
| ASTM D 3666 : 2000 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 6752 : 2003 | Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Automatic Vacuum Sealing Method |
| ASTM D 6752 : 2002 | Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Automatic Vacuum Sealing Method |
| ASTM D 6925 : 2006 | Standard Test Method for Preparation and Determination of the Relative Density of Hot Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor |
| ASTM D 2726 : 2008 | Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures |
| ASTM D 3666 : 2007 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2007 : EDT 2 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 1188 : 1996 : R2002 | Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Paraffin-Coated Specimens |
| ASTM D 3666 : 2016 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2003 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 2726 : 2009 | Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures |
| ASTM D 1188 : 1996 : EDT 1 | Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Paraffin-Coated Specimens |
| ASTM D 3666 : 2001 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 6925 : 2009 | Standard Test Method for Preparation and Determination of the Relative Density of Hot Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor |
| ASTM D 2726 : 2005 : REV A | Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures |
| ASTM D 3666 : 2006 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| AASHTO TP 79 : 2013 | METHOD OF TEST FOR DETERMINING THE DYNAMIC MODULUS AND FLOW NUMBER FOR ASPHALT MIXTURES USING THE ASPHALT MIXTURE PERFORMANCE TESTER (AMPT) |
| ASTM D 6925 : 2003 | Standard Test Method for Preparation and Determination of the Relative Density of Hot Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor |
| ASTM D 3666 : 2004 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 6857 : 2009 | Standard Test Method for Maximum Specific Gravity and Density of Bituminous Paving Mixtures Using Automatic Vacuum Sealing Method |
| ASTM D 3666 : 2005 : REV A | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2007 : REV A : EDT 1 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 3666 : 2009 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 6752 : 2009 | Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Automatic Vacuum Sealing Method |
| ASTM D 3666 : 2002 | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM D 2726 : 2011 | Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures |
$122.77
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.