ASTM E 1164 : 2012 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
13-07-2023
English
01-07-2012
CONTAINED IN VOL. 06.01, 2017 Specifies the instrumental measurement requirements, calibration procedures, and material standards needed to obtain precise spectral data for computing the colors of objects.
1.1This practice covers the instrumental measurement requirements, calibration procedures, and material standards needed to obtain precise spectral data for computing the colors of objects.
1.2This practice lists the parameters that must be specified when spectrometric measurements are required in specific methods, practices, or specifications.
1.3Most sections of this practice apply to both spectrometers, which can produce spectral data as output, and spectrocolorimeters, which are similar in principle but can produce only colorimetric data as output. Exceptions to this applicability are noted.
1.4This practice is limited in scope to spectrometers and spectrometric colorimeters that employ only a single monochromator. This practice is general as to the materials to be characterized for color.
1.5The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
E 12
|
| DocumentType |
Standard Practice
|
| Pages |
9
|
| ProductNote |
Reconfirmed EDT 1
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 1729 : 2016 | Standard Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials |
| ASTM D 2244 : 2016 | Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates |
| ASTM C 1510 : 2001 : R2016 | Standard Test Method for Color and Color Difference of Whitewares by Abriged Spectrophotometry |
| ASTM D 7195 : 2016 : REV A | Standard Guide for Setting Object Color Specifications |
| ASTM E 308 : 2018 | Standard Practice for Computing the Colors of Objects by Using the CIE System |
| ASTM E 1349 : 2006 : R2018 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Bidirectional (45°:0° or 0°:45°) Geometry |
| ASTM D 1535 : 2014 : R2018 | Standard Practice for Specifying Color by the Munsell System |
| ASTM E 1360 : 2005 : R2015 | Standard Practice for Specifying Color by Using the Optical Society of America Uniform Color Scales System |
| ASTM D 8163 : 2018 | Standard Test Method for Determination of Strength of Colorants and Bases for Architectural, Marine, Maintenance, Commercial, and Industrial Coatings |
| ASTM E 2539 : 2014 : R2017 | Standard Test Method for Multiangle Color Measurement of Interference Pigments |
| ASTM E 1247 : 2012 : R2017 | Standard Practice for Detecting Fluorescence in Object-Color Specimens by Spectrophotometry |
| ASTM E 1347 : 2006 : R2015 | Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry |
| ASTM D 3451 : 2006 : R2017 | Standard Guide for Testing Coating Powders and Powder Coatings |
| ASTM D 5531 : 2017 | Standard Guide for Preparation, Maintenance, and Distribution of Physical Product Standards for Color and Geometric Appearance of Coatings |
| ASTM E 2301 : 2012 : R2017 | Standard Test Method for Daytime Colorimetric Properties of Fluorescent Retroreflective Sheeting and Marking Materials for High Visibility Traffic Control and Personal Safety Applications Using 45°:Normal Geometry |
| ASTM E 3125 : 2017 | Standard Test Method for Evaluating the Point-to-Point Distance Measurement Performance of Spherical Coordinate 3D Imaging Systems in the Medium Range |
| ASTM E 2153 : 2001 : R2017 | Standard Practice for Obtaining Bispectral Photometric Data for Evaluation of Fluorescent Color |
| ASTM E 2630 : 2008 : R2013 | Standard Test Method for Luminance Ratio of a Fluorescent Specimen using a Narrow Band Source (Withdrawn 2022) |
| ASTM E 1331 : 2015 | Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Hemispherical Geometry |
| ASTM C 1650 : 2014 | Standard Practice for Instrumental Reflectance Measurement of Color for Flat Glass, Coated, and Uncoated |
| ASTM D 2205 : 2015 | Standard Guide for Selection of Tests for Traffic Paints |
| ASTM D 3134 : 2015 | Standard Practice for Establishing Color and Gloss Tolerances |
| ASTM D 6131 : 2017 | Standard Test Method for Evaluating the Relative Tint Undertone of Titanium Dioxide Pigments |
| ASTM E 2175 : 2001 : R2013 | Standard Practice for Specifying the Geometry of Multiangle Spectrophotometers |
| ASTM E 991 : 2016 | Standard Practice for Color Measurement of Fluorescent Specimens Using the One-Monochromator Method |
| ASTM E 805 : 2012 : REV A : R2017 | Standard Practice for Identification of Instrumental Methods of Color or Color-Difference Measurement of Materials |
| ASTM E 313 : 2015 : EDT 1 | Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates |
| ASTM D 1746 : 2015 | Standard Test Method for Transparency of Plastic Sheeting |
| ASTM E 179 : 2017 | Standard Guide for Selection of Geometric Conditions for Measurement of Reflection and Transmission Properties of Materials |
| ASTM E 2970 : 2015 | Standard Practice for Specifying Color by the Natural Colour System (NCS) |
| ASTM E 1477 : 1998 : REV A : R2017 : EDT 1 | Standard Test Method for Luminous Reflectance Factor of Acoustical Materials by Use of Integrating-Sphere Reflectometers |
| ASTM D 4956 : 2019 | Standard Specification for Retroreflective Sheeting for Traffic Control |
| ASTM D 4960 : 2008 : R2013 | Standard Test Method for Evaluation of Color for Thermoplastic Traffic Marking Materials |
| ASTM D 4838 : 1988 : R2016 | Standard Test Method for Determining the Relative Tinting Strength of Chromatic Paints (Withdrawn 2023) |
| ASTM E 2938 : 2015 | Standard Test Method for Evaluating the Relative-Range Measurement Performance of 3D Imaging Systems in the Medium Range |
| ASTM E 2214 : 2019 | Standard Practice for Specifying and Verifying the Performance of Color-Measuring Instruments |
| ASTM E 3040 : 2018 | Standard Practice for Evaluation of Instrumental Color Difference with a Gray Scale |
| ASTM E 284 : 2017 | Standard Terminology of Appearance |
| ASTM C 1501 : 2019 | Standard Test Method for Color Stability of Building Construction Sealants as Determined by Laboratory Accelerated Weathering Procedures |
| ASTM C 1649 : 2014 | Standard Practice for Instrumental Transmittance Measurement of Color for Flat Glass, Coated and Uncoated |
| ASTM D 3794 : 2018 | Standard Guide for Testing Coil Coatings |
| ASTM E 1348 : 2015 : EDT 1 | Standard Test Method for Transmittance and Color by Spectrophotometry Using Hemispherical Geometry |
| ASTM D 5326 : 1994 : REV A : R2013 | Standard Test Method for Color Development in Tinted Latex Paints |
| ASTM D 6961/D6961M : 2009 : R2015 : EDT 1 | Standard Test Method for Color Measurement of Flax Fiber |
| ASTM D 4941 : 2006 : R2016 | Standard Practice for Preparing Drawdowns of Artists’ Paste Paints |
| ASTM D 4890 : 2018 | Standard Test Methods for Polyurethane Raw Materials: Determination of Gardner and APHA Color of Polyols |
| ASTM E 275 : 2008 | Describing and Measuring Performance of Ultraviolet and Visible Spectrophotometers |
| ASTM E 284 : 2017 : REDLINE | Standard Terminology of Appearance |
| ASTM D 1003 : 2013 : REDLINE | Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics |
| ASTM E 991 : 2016 : REDLINE | Standard Practice for Color Measurement of Fluorescent Specimens Using the One-Monochromator Method |
| ISO 2469:2014 | Paper, board and pulps — Measurement of diffuse radiance factor (diffuse reflectance factor) |
| ASTM E 179 : 2017 : REDLINE | Standard Guide for Selection of Geometric Conditions for Measurement of Reflection and Transmission Properties of Materials |
| ASTM E 958 : 2013 : REDLINE | Standard Practice for Estimation of the Spectral Bandwidth of Ultraviolet-Visible Spectrophotometers |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.