Customer Support: 131 242

i2i Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search

ASTM E 1324 : 2016 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Guide for Measuring Some Electronic Characteristics of Ultrasonic Testing Instruments
Available format(s)

PDF

Superseded date

01-07-2021

Language(s)

English

Published date

01-06-2016

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 03.03, 2017 Specifies procedures for electronically measuring performance-related characteristics of some sections of ultrasonic instruments.

1.1This guide describes procedures for electronically measuring the following performance-related characteristics of some sections of ultrasonic instruments:

1.1.1Power Supply Section:

      line regulation,
       battery discharge time, and
       battery charge time.

1.1.2Pulser Section:
     pulse shape,
      pulse amplitude,
      pulse rise time, pulse length, and
      pulse frequency spectrum.

1.1.3Receiver Section:
       vertical linearity,
        frequency response,
        noise and sensitivity, and
        dB controls.

1.1.4Time Base Section:
     horizontal linearity, and
      clock (pulse repetition rate).

1.1.5Gate/Alarm Section:
        delay and width,
         resolution,
         alarm level,
         gain uniformity,
         analog output, and
         back echo gate.

1.2This guide complements Practice E317, D2548 and is not intended for evaluating the performance characteristics of ultrasonic testing instruments on the inspection/production line.

Note 1:No access to internal circuitry is required.

1.3Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
E 07
DocumentType
Redline
Pages
14
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM E 127 : 2015 : REDLINE Standard Practice for Fabrication and Control of Aluminum Alloy Ultrasonic Standard Reference Blocks
ASTM E 317 : 2016 : REDLINE Standard Practice for Evaluating Performance Characteristics of Ultrasonic Pulse-Echo Testing Instruments and Systems without the Use of Electronic Measurement Instruments
ASTM D 5300 : 1993 Standard Test Method for Measurement of Resin Content and Other Related Properties of Polymer Matrix Thermoset Prepreg by Combined Mechanical and Ultrasonic Methods (Withdrawn 2000)
ASTM C 1175 : 1999 : REV A : R2004 Standard Guide to Test Methods and Standards for Nondestructive Testing of Advanced Ceramics
ASTM E 2373/E2373M : 2014 : REDLINE Standard Practice for Use of the Ultrasonic Time of Flight Diffraction (TOFD) Technique
SAE AS 7114/3 : 2008 NADCAP REQUIREMENTS FOR NONDESTRUCTIVE TESTING FACILITY ULTRASONIC SURVEY
ASTM E 2775 : 2016 : REDLINE Standard Practice for Guided Wave Testing of Above Ground Steel Pipework Using Piezoelectric Effect Transduction
ASTM E 2929 : 2013 Standard Practice for Guided Wave Testing of Above Ground Steel Piping with Magnetostrictive Transduction
ISO 12710:2002 Non-destructive testing Ultrasonic inspection Evaluating electronic characteristics of ultrasonic test instruments
ASTM C 1175 : 1999 : REV A : R2010 Standard Guide to Test Methods and Standards for Nondestructive Testing of Advanced Ceramics (Withdrawn 2018)
ABS 0014 : 2018 GUIDE FOR NONDESTRUCTIVE INSPECTION OF HULL WELDS
ASTM C 1175 : 1999 : REV A Standard Guide to Test Methods and Standards for Nondestructive Testing of Advanced Ceramics

ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
ISO 10012:2003 Measurement management systems — Requirements for measurement processes and measuring equipment
ASTM E 317 : 2016 : REDLINE Standard Practice for Evaluating Performance Characteristics of Ultrasonic Pulse-Echo Testing Instruments and Systems without the Use of Electronic Measurement Instruments

View more information
$135.86
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more