Customer Support: 131 242

i2i Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search
Home
ASTM
ASTM E 161 : 2017

ASTM E 161 : 2017

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Electroformed Material and Test Sieves

Available format(s)

Hardcopy , PDF

Superseded date

05-11-2021

Language(s)

English

Published date

01-02-2018

Publisher

American Society for Testing and Materials

1.1 This specification covers the technical requirements for design and construction of electroformed sieves and sieve material.

1.1This specification covers the technical requirements for design and construction of electroformed sieves and sieve material. These sieves are used to perform particle-size analysis and in preparing narrowly designated particle -size fractions. They may also be used as reference standards when suitably certified. The method of certifying these sieves is included in Annex A1.

1.2The values stated in SI units shall be considered standard for the dimensions of the electroformed mesh openings and the size of the line width in the electroformed mesh. The values stated in inch-pound units shall be considered standard with regard to the sieve frames and to lines per unit length, as in Table 1. The values given in parentheses are mathematical conversions that are provided for informational purposes only, and are not considered standard.

(A)These nominal size openings are from the preferred number series R40/3 and R10. (Openings on apertures 32 μm and less are series R10.) These standard designations correspond to the values for test sieve apertures recommended by the International Organization for Standardization (ISO). These sizes are typical, other opening sizes are available.
(B)Because of their greater durability in routine testing, sieves made close to the minimum limit are normally supplied. Sieves made close to the maximum limit may be obtained only on special order but are preferable from the standpoint of logical progression and better test completion time.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
E 29
DocumentType
Standard
Pages
4
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 4513 : 2011 : R2017 Standard Test Method for Particle Size Distribution of Catalytic Materials by Sieving
ASTM C 430 : 2017 Standard Test Method for Fineness of Hydraulic Cement by the 45-μm (No. 325) Sieve
ASTM C 925 : 2009(R2019) Standard Guide for Precision Electroformed Wet Sieve Analysis of Nonplastic Ceramic Powders
ASTM E 2651 : 2019 Standard Guide for Powder Particle Size Analysis
ASTM F 1877 : 2016 Standard Practice for Characterization of Particles
ASTM E 11 : 2020 Standard Specification for Woven Wire Test Sieve Cloth and Test Sieves

ASTM E 1638 : 1994 : R2004 Standard Terminology Relating to Sieve Analysis
ASTM E 1638 : 2007 Standard Terminology Relating to Sieves, Sieving Methods and Screening Media
ASTM E 1638 : 2010 Standard Terminology Relating to Sieves, Sieving Methods, and Screening Media
ASTM E 1638 : 2018 Standard Terminology Relating to Sieves, Sieving Methods, and Screening Media
ASTM E 1638 : 2013 Standard Terminology Relating to Sieves, Sieving Methods, and Screening Media
ASTM E 1638 : 2007 : REV A Standard Terminology Relating to Sieves, Sieving Methods and Screening Media
ASTM E 1638 : 2012 Standard Terminology Relating to Sieves, Sieving Methods, and Screening Media
ASTM E 1638 : 1994 : R1999 Standard Terminology Relating to Sieve Analysis
ASTM E 1638 : 2011 : REV A Standard Terminology Relating to Sieves, Sieving Methods, and Screening Media
ASTM E 1638 : 2009 Standard Terminology Relating to Sieves, Sieving Methods and Screening Media

View more information
$108.03
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more