Name: ASTM E 1640 : 2013
Brand: ASTM
Price: 122.77 AUD

ASTM E 1640 : 2013

Superseded

View Superseded by

Standard Test Method for Assignment of the Glass Transition Temperature By Dynamic Mechanical Analysis

Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

01-08-2013

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 14.05, 2018 Describes the assignment of a glass transition temperature (T[g]) of materials using dynamic mechanical analyzers.

1.1This test method covers the assignment of a glass transition temperature (T_g) of materials using dynamic mechanical analyzers.

1.2This test method is applicable to thermoplastic polymers, thermoset polymers, and partially crystalline materials which are thermally stable in the glass transition region.

1.3The applicable range of temperatures for this test method is dependent upon the instrumentation used, but, in order to encompass all materials, the minimum temperature should be about −150°C.

1.4This test method is intended for materials having an elastic modulus in the range of 0.5 MPa to 100 GPa.

1.5The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.6This standard is similar to IEC 61006 except that standard uses the peak temperature of the loss modulus peak as the glass transition temperature while this standard uses the extrapolated onset temperature of the storage modulus change.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee	E 37
DocumentType	Test Method
Pages	6
ProductNote	Reconfirmed 2013
PublisherName	American Society for Testing and Materials
Status	Superseded
SupersededBy	ASTM E 1640 : 2013 : R2018
Supersedes	ASTM E 1640 : 2009

ASTM D 3794 : 2018	Standard Guide for Testing Coil Coatings
ASTM E 1867 : 2018	Standard Test Methods for Temperature Calibration of Dynamic Mechanical Analyzers
ASTM E 2602 : 2009 : R2015	Standard Test Methods for the Assignment of the Glass Transition Temperature by Modulated Temperature Differential Scanning Calorimetry
ASTM D 7028 : 2007 : R2015	Standard Test Method for Glass Transition Temperature (DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA)
ASTM F 3131 : 2014	Standard Specification for Epoxy / Cotton Raw Materials for the Use in Bearing Cages
ASTM F 942 : 2018	Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures

ASTM E 2425 : 2016 : REDLINE	Standard Test Method for Loss Modulus Conformance of Dynamic Mechanical Analyzers
ASTM E 1142 : 2015 : REDLINE	Standard Terminology Relating to Thermophysical Properties
IEC 61006:2004	Electrical insulating materials - Methods of test for the determination of the glass transition temperature

View more information

$122.77

Including GST where applicable

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

Log into your Account

ASTM E 1640 : 2013

Superseded

Abstract

Scope

General Product Information

Standards Referenced By This Book

Standards Referencing This Book

Category

Subcategory

Access your standards online with a subscription