Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 1645 : 2016

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Preparation of Dried Paint Samples by Hotplate or Microwave Digestion for Subsequent Lead Analysis
Available format(s)

Hardcopy , PDF

Superseded date

14-10-2020

Language(s)

English

Published date

01-03-2016

This practice covers the sample preparation procedures for paint samples that are collected during the assessment, management or control of lead hazards.

1.1This practice covers the sample preparation procedures for paint samples that are collected during the assessment, management or control of lead hazards.

1.2This practice describes the digestion procedures using a hot plate or microwave oven or apparatus for paint samples that are to be analyzed for lead content.

1.3This practice covers the general considerations for quantitative sample extraction for total recoverable lead in dried paint samples (either bulk paint or paint powder) using hot plate or microwave heating techniques, or both.

1.4This practice contains notes that are explanatory and not part of the mandatory requirements of the standard.

1.5This practice is based on two NIOSH Methods, 7082 and 7105, and on an EPA standard operating procedure for lead in paint.

1.6The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 6.1.2, 6.1.2.1, 6.1.2.2, 6.3.2.4, 7.2.1, and 7.2.2.

Committee
D 22
DocumentType
Standard Practice
Pages
5
ProductNote
THIS STANDARD ALSO REFERS TO :ISO 8655,NTIS No. PB92–114172,NMAM 7082
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM E 3193 : 2019 Standard Test Method for Measurement of Lead (Pb) in Dust by Wipe, Paint, and Soil by Flame Atomic Absorption Spectrophotometry (FAAS)
ASTM E 1775 : 2016 Standard Guide for Evaluating Performance of On-Site Extraction and Field-Portable Electrochemical or Spectrophotometric Analysis for Lead
ASTM D 7876 : 2013 : R2018 Standard Practice for Practice for Sample Decomposition Using Microwave Heating (With or Without Prior Ashing) for Atomic Spectroscopic Elemental Determination in Petroleum Products and Lubricants
ASTM E 2119 : 2016 Standard Practice for Quality Systems for Conducting In Situ Measurements of Lead Content in Paint or Other Coatings Using Field-Portable X-Ray Fluorescence (XRF) Devices
ASTM E 3203 : 2019 Standard Test Method for Determination of Lead in Dried Paint, Soil, and Wipe Samples by Inductively Coupled Plasma-Optical Emission Spectroscopy (ICP-OES)
ASTM A 888 : 2018 : REV A Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications
ASTM A 74 : 2017 Standard Specification for Cast Iron Soil Pipe and Fittings
ASTM A 1111 : 2018 Standard Specification for Cast Iron Closet Flanges for Use With Cast Iron Soil Pipe and Fittings in Gravity Flow Plumbing Drain, Waste, and Vent Sanitary Applications
ASTM E 1583 : 2017 Standard Practice for Evaluating Laboratories Engaged in Determination of Lead in Paint, Dust, Airborne Particulates, and Soil Taken From and Around Buildings and Related Structures
ASTM E 1613 : 2012 Standard Test Method for Determination of Lead by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES), Flame Atomic Absorption Spectrometry (FAAS), or Graphite Furnace Atomic Absorption Spectrometry (GFAAS) Techniques (Withdrawn 2021)
ASTM A 1109 : 2018 Standard Specification for Special Fittings for Single-Stack Hubless Cast Iron Soil Pipe Fittings for Sanitary, Waste, and Vent Piping Applications
ASTM E 2115 : 2015 Standard Guide for Conducting Lead Hazard Assessments of Dwellings and of Other Child-Occupied Facilities
ASTM E 631 : 2015 Standard Terminology of Building Constructions

ASTM D 1129 : 2003 Standard Terminology Relating to Water
ASTM D 1129 : 2013 Standard Terminology Relating to Water
ASTM D 1129 : 2013 : R2020 Standard Terminology Relating to Water
ASTM D 1193 : 1977 : R1983 : EDT 1 Standard Specification for Reagent Water
ASTM D 1129 : 2006 Standard Terminology Relating to Water
ASTM E 1605 : 2001 : REV B Standard Terminology Relating to Lead in Buildings
ASTM D 1129 : 1999 : REV A Standard Terminology Relating to Water
ASTM D 1129 : 2006 : REV A Standard Terminology Relating to Water
ASTM D 1193 : 2006 : R2011 Standard Specification for Reagent Water
ASTM E 1605 : 2000 Standard Terminology Relating to Lead in Buildings
ASTM E 1605 : 2018 Standard Terminology Relating to Lead in Buildings
ASTM D 1129 : 2003 : REV A Standard Terminology Relating to Water
ASTM D 1129 : 2002 Standard Terminology Relating to Water
ASTM E 1605 : 2018 : REV A Standard Terminology Relating to Lead in Buildings
ASTM E 1605 : 2001 : REV A Standard Terminology Relating to Lead in Buildings
ASTM D 1193 : 1991 Standard Specification for Reagent Water
ASTM E 1605 : 2003 : EDT 1 Standard Terminology Relating to Lead in Buildings
ASTM E 1605 : 2019 Standard Terminology Relating to Lead in Buildings
ASTM D 1129 : 2004 Standard Terminology Relating to Water
ASTM E 1605 : 2003 Standard Terminology Relating to Lead in Buildings
ASTM D 1129 : 2002 : REV A Standard Terminology Relating to Water
ASTM E 1605 : 2018 : REV B Standard Terminology Relating to Lead in Buildings
ASTM E 1605 : 2004 Standard Terminology Relating to Lead in Buildings
ASTM D 1193 : 1970 Standard Specification For Reagent Water
ASTM D 1193 : 2006 Standard Specification for Reagent Water
ASTM D 1193 : 1999 Standard Specification for Reagent Water
ASTM D 1129 : 2010 Standard Terminology Relating to Water
ASTM E 1605 : 2001 Standard Terminology Relating to Lead in Buildings
ASTM D 1129 : 2006 : REV A : EDT 1 Standard Terminology Relating to Water
ASTM D 1129 : 2001 Standard Terminology Relating to Water
ASTM D 1129 : 2004 : EDT 1 Standard Terminology Relating to Water
ASTM D 1193 : 2006 : R2018 Standard Specification for Reagent Water
ASTM E 1605 : 2004 : R2012 Standard Terminology Relating to Lead in Buildings
ASTM E 1605 : 2002 Standard Terminology Relating to Lead in Buildings

View more information
$122.77
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more