ASTM E 1734 : 2016 : REV A
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Practice for Radioscopic Examination of Castings
Available format(s)
Hardcopy , PDF
Superseded date
30-06-2023
Language(s)
English
Published date
24-01-2017
1.1This practice covers a uniform procedure for radioscopic examination of castings. Radioscopic examination of weldments can be found in E1416.
1.2This practice applies only to radioscopic examination in which an image is finally presented on a display screen (monitor) for evaluation. Test part acceptance may be based on a static or dynamic image. The examination results may be recorded for later review. This practice does not apply to fully automated systems in which evaluation is performed automatically by a computer.
1.3Due to the many complex geometries and part configurations inherent with castings, it is necessary to recognize the potential limitations associated with obtaining complete radioscopic coverage. Consideration shall be given to areas where geometry or part configuration does not allow for complete radioscopic coverage.
1.4The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
E 07
|
| DocumentType |
Standard Practice
|
| Pages |
9
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM E 1647 : 2016 | Standard Practice for Determining Contrast Sensitivity in Radiology |
| ASTM E 1316 : 2022 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 2002 : 2022 | Standard Practice for Determining Image Unsharpness and Basic Spatial Resolution in Radiography and Radioscopy |
| ASTM E 1411 : 2001 : R2006 | Standard Practice for Qualification of Radioscopic Systems |
| ASTM E 1316 : 2011 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2015 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 2339 : 2004 | Standard Practice for Digital Imaging and Communication in Nondestructive Evaluation (DICONDE) |
| ASTM E 1255 : 2009 | Standard Practice for Radioscopy |
| ASTM E 1742 : 2000 | Standard Practice for Radiographic Examination |
| ASTM E 1025 : 2011 | Standard Practice for Design, Manufacture, and Material Grouping Classification of Hole-Type Image Quality Indicators (IQI) Used for Radiology |
| ASTM E 1316 : 2009 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2008 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2010 : REV C | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2020 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2017 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 : REV C | Standard Terminology for Nondestructive Examinations |
| ASTM E 1647 : 2003 | Standard Practice for Determining Contrast Sensitivity in Radioscopy |
| ASTM E 2339 : 2011 | Standard Practice for Digital Imaging and Communication in Nondestructive Evaluation (DICONDE) |
| ASTM E 1316 : 2000 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1475 : 2013 | Standard Guide for Data Fields for Computerized Transfer of Digital Radiological Examination Data |
| ASTM E 1255 : 1996 | Standard Practice for Radioscopy |
| ASTM E 543 : 2021 | Standard Specification for Agencies Performing Nondestructive Testing |
| ASTM E 1316 : 2019 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1165 : 2012 : R2017 | Standard Test Method for Measurement of Focal Spots of Industrial X-Ray Tubes by Pinhole Imaging |
| ASTM E 1316 : 2014 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1475 : 1997 | Standard Guide for Data Fields for Computerized Transfer of Digital Radiological Test Data |
| ASTM E 2339 : 2015 | Standard Practice for Digital Imaging and Communication in Nondestructive Evaluation (DICONDE) |
| ASTM E 1000 : 1998 | Standard Guide for Radioscopy |
| ASTM E 1316 : 2013 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1000 : 2016 | Standard Guide for Radioscopy |
| ASTM E 1316 : 2018 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2011 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2007 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2015 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1165:2012 | Standard Test Method for Measurement of Focal Spots of Industrial X-Ray Tubes by Pinhole Imaging |
| ASTM E 1316 : 2019 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2021 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1025 : 2018 | Standard Practice for Design, Manufacture, and Material Grouping Classification of Hole-Type Image Quality Indicators (IQI) Used for Radiography |
| ASTM E 1316 : 2013 : REV D | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2000 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2019 | Standard Terminology for Nondestructive Examinations |
| ASTM E 2002 : 1998 | Standard Practice for Determining Total Image Unsharpness in Radiology |
| ASTM E 1316 : 2001 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1416 : 2023 | Standard Practice for Radioscopic Examination of Weldments |
| ASTM E 1411 : 1995 | Standard Practice for Qualification of Radioscopic Systems |
| ASTM E 1165 : 1992 : R1996 : EDT 1 | Standard Test Method for Measurement of Focal Spots of Industrial X-Ray Tubes by Pinhole Imaging |
| ASTM E 1316 : 2003 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1000 : 1998 : R2003 | Standard Guide for Radioscopy |
| ASTM E 1742 : 2008 : REV A | Standard Practice for Radiographic Examination |
| ASTM E 1316 : 2018 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1416 : 2009 | Standard Test Method for Radioscopic Examination of Weldments |
| ASTM E 1647 : 2009 | Standard Practice for Determining Contrast Sensitivity in Radioscopy |
| ASTM E 1316 : 2006 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 543 : 2015 | Standard Specification for Agencies Performing Nondestructive Testing |
| ASTM E 1316 : 2016 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1416 : 2016 : REV A | Standard Practice for Radioscopic Examination of Weldments |
| ASTM E 2002 : 1998 : R2003 : EDT 1 | Standard Practice for Determining Total Image Unsharpness in Radiology |
| ASTM E 2339 : 2008 | Standard Practice for Digital Imaging and Communication in Nondestructive Evaluation (DICONDE) |
| ASTM E 2339 : 2021 | Standard Practice for Digital Imaging and Communication in Nondestructive Evaluation (DICONDE) |
| ASTM E 2903 : 2018 | Standard Test Method for Measurement of the Effective Focal Spot Size of Mini and Micro Focus X-ray Tubes |
| ASTM E 2002 : 1998 : R2009 | Standard Practice for Determining Total Image Unsharpness in Radiology |
| ASTM E 1316 : 2021 : REV D | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2002 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1475 : 2013 : R2018 | Standard Guide for Data Fields for Computerized Transfer of Digital Radiological Examination Data |
| ASTM E 1453 : 2009 | Standard Guide for Storage of Magnetic Tape Media that Contains Analog or Digital Radioscopic Data |
| ASTM E 1316 : 2014 : EDT 1 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1025 : 2005 | Standard Practice for Design, Manufacture, and Material Grouping Classification of Hole-Type Image Quality Indicators (IQI) Used for Radiology |
| ASTM E 2339 : 2006 | Standard Practice for Digital Imaging and Communication in Nondestructive Evaluation (DICONDE) |
| ASTM E 1316 : 2010 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2022 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1165 : 2020 | Standard Test Method for Measurement of Focal Spots of Industrial X-Ray Tubes by Pinhole Imaging |
| ASTM E 1453 : 2014 | Standard Guide for Storage of Magnetic Tape Media that Contains Analog or Digital Radioscopic Data |
| ASTM E 1316 : 2013 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2021 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1742 : 2005 | Standard Practice for Radiographic Examination |
| ASTM E 1416 : 2004 | Standard Test Method for Radioscopic Examination of Weldments |
| ASTM E 1453 : 1993 : R1996 | Standard Guide for Storage of Media That Contains Analog or Digital Radioscopic Data |
| ASTM E 1411 : 2001 | Standard Practice for Qualification of Radioscopic Systems |
| ASTM E 1025 : 1998 | Standard Practice for Design, Manufacture, and Material Grouping Classification of Hole-Type Image Quality Indicators (IQI) Used for Radiology |
| ASTM E 1316 : 2017 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 2339 : 2010 | Standard Practice for Digital Imaging and Communication in Nondestructive Evaluation (DICONDE) |
| ASTM E 1416 : 1996 | Standard Test Method for Radioscopic Examination of Weldments |
| ASTM E 2903 : 2013 | Standard Test Method for Measurement of the Effective Focal Spot Size of Mini and Micro Focus X-ray Tubes |
| ASTM E 1316 : 2016 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1647 : 1998 : REV A | Standard Practice for Determining Contrast Sensitivity in Radioscopy |
| ASTM E 1411 : 2016 | Standard Practice for Qualification of Radioscopic Systems |
| ASTM E 1316 : 2009 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1647 : 2016 | Standard Practice for Determining Contrast Sensitivity in Radiology |
| ASTM E 1316 : 2002 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2004 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1416 : 2016 | Standard Practice for Radioscopic Examination of Weldments |
| ASTM E 1316 : 2007 : REV C | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2010 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2013 : REV A | Standard Terminology for Nondestructive Examinations |
| ASTM E 1475 : 2002 : R2008 | Standard Guide for Data Fields for Computerized Transfer of Digital Radiological Examination Data |
| ASTM E 1411 : 2009 | Standard Practice for Qualification of Radioscopic Systems |
| ASTM E 2002 : 2015 | Standard Practice for Determining Total Image Unsharpness and Basic Spatial Resolution in Radiography and Radioscopy |
| ASTM E 1000 : 1998 : R2009 | Standard Guide for Radioscopy |
| ASTM E 1742 : 2006 | Standard Practice for Radiographic Examination |
| ASTM E 1165 : 1992 : R2002 | Standard Test Method for Measurement of Focal Spots of Industrial X-Ray Tubes by Pinhole Imaging |
| ASTM E 1475 : 2002 | Standard Guide for Data Fields for Computerized Transfer of Digital Radiological Test Data |
| ASTM E 1316 : 2021 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2007 : REV B | Standard Terminology for Nondestructive Examinations |
| ASTM E 1165 : 2004 : R2010 | Standard Test Method for Measurement of Focal Spots of Industrial X-Ray Tubes by Pinhole Imaging |
| ASTM E 1647 : 2016 : R2022 | Standard Practice for Determining Contrast Sensitivity in Radiology |
| ASTM E 1316 : 2005 | Standard Terminology for Nondestructive Testing |
| ASTM E 1316 : 2004 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1165 : 2004 | Standard Test Method for Measurement of Focal Spots of Industrial X-Ray Tubes by Pinhole Imaging |
| ASTM E 1316 : 2021 : REV C | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2007 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1316 : 2023 | Standard Terminology for Nondestructive Examinations |
| ASTM E 1255 : 2016 | Standard Practice for Radioscopy |
| ASTM E 1316 : 2012 | Standard Terminology for Nondestructive Examinations |
$122.77
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.