ASTM E 1952 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Method for Thermal Conductivity and Thermal Diffusivity by Modulated Temperature Differential Scanning Calorimetry
Hardcopy , PDF
30-06-2023
English
19-09-2017
This test method describes the determination of thermal conductivity of homogeneous, non-porous solid materials in the range of 0.10 W/(K • m) to 1.0 W/(K • m) by modulated temperature differential scanning calorimeter.
1.1This test method describes the determination of thermal conductivity of homogeneous, non-porous solid materials in the range of 0.10 W/(K • m) to 1.0 W/(K • m) by modulated temperature differential scanning calorimeter. This range includes many polymeric, glass, and ceramic materials. Thermal diffusivity, which is related to thermal conductivity through specific heat capacity and density, may also be derived. Thermal conductivity and diffusivity can be determined at one or more temperatures over the range of 0°C to 90°C.
1.2The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
E 37
|
| DocumentType |
Test Method
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM E 1231 : 2015 | Standard Practice for Calculation of Hazard Potential Figures of Merit for Thermally Unstable Materials |
| ASTM E 1142 : 2022 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2022 : REV D | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 2161 : 2015 : R2019 | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 2161 : 2023 | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1142 : 2011 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2012 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2022 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 2161 : 2015 | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1142 : 1997 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2021 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 2161 : 2013 | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 1231 : 2010 | Standard Practice for Calculation of Hazard Potential Figures-of-Merit for Thermally Unstable Materials |
| ASTM E 2161 : 2022 : REV B | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1142 : 2013 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2004 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2022 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2022 : REV C | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2022 : REV B | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 1142 : 2006 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2018 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 1231 : 2001 : R2006 | Standard Practice for Calculation of Hazard Potential Figures-of-Merit for Thermally Unstable Materials |
| ASTM E 1142 : 2015 : R2020 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2161 : 2021 : REV A | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 968 : 2002 : R2014 | Standard Practice for Heat Flow Calibration of Differential Scanning Calorimeters (Withdrawn 2023) |
| ASTM E 2161 : 2022 | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1142 : 2021 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2161 : 2001 | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 2161 : 2006 : REV A | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 2161 : 2022 : REV A | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 473 : 2022 : REV C | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 2161 : 2008 | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 1231 : 2001 | Standard Practice for Calculation of Hazard Potential Figures-of-Merit for Thermally Unstable Materials |
| ASTM E 2161 : 2023 : REV A | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1142 : 2007 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2161 : 2021 | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 2161 : 2023 : REV B | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 2161 : 2021 : REV B | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1231 : 2001 : EDT 1 | Standard Practice for Calculation of Hazard Potential Figures-of-Merit for Thermally Unstable Materials |
| ASTM E 1142 : 2022 : REV B | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2014 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2014 : REV B | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2023 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2005 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2015 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2021 : REV A | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 968 : 1999 | Standard Practice for Heat Flow Calibration of Differential Scanning Calorimeters |
| ASTM E 2161:2006 | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 473 : 2022 : REV A | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 1142 : 2011 : REV B | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2021 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2161 : 2007 : REV A | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 1231 : 1996 : REV A | Standard Practice for Calculation of Hazard Potential Figures-of-Merit for Thermally Unstable Materials |
| ASTM E 1142 : 2023 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1231 : 2015 | Standard Practice for Calculation of Hazard Potential Figures of Merit for Thermally Unstable Materials |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.