ASTM E 220 : 2013 : REDLINE
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Method for Calibration of Thermocouples By Comparison Techniques
Available format(s)
PDF
Superseded date
27-01-2020
Language(s)
English
Published date
01-11-2013
CONTAINED IN VOL. 14.03, 2017 Specifies the principles, apparatus, and procedure for calibrating thermocouples by comparison with a reference thermometer.
1.1This test method describes the principles, apparatus, and procedure for calibrating thermocouples by comparison with a reference thermometer. Calibrations are covered over temperature ranges appropriate to the individual types of thermocouples within an overall range from approximately −195 to 1700 °C (−320 to 3100 °F).
1.2In general, this test method is applicable to unused thermocouples. This test method does not apply to used thermocouples due to their potential material inhomogeneity—the effects of which cannot be identified or quantified by standard calibration techniques. Thermocouples with large-diameter thermoelements and sheathed thermocouples may require special care to control thermal conduction losses.
1.3In this test method, all values of temperature are based on the International Temperature Scale of 1990. See Guide E1594.
1.4This standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
| Committee |
E 20
|
| DocumentType |
Redline
|
| Pages |
17
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
| ASTM C 24 : 2009 : R2013 | Standard Test Method for Pyrometric Cone Equivalent (PCE) of Fireclay and High Alumina Refractory Materials |
| ASTM A 1080 : 2015 : REDLINE | Standard Practice for Hot Isostatic Pressing of Steel, Stainless Steel, and Related Alloy Castings |
| ASTM D 6007 : 2014 : REDLINE | Standard Test Method for Determining Formaldehyde Concentrations in Air from Wood Products Using a Small-Scale Chamber |
| BS ISO 13573:2012 | Corrosion of metals and alloys. Test method for thermal-cycling exposure testing under high-temperature corrosion conditions for metallic materials |
| ISO/TTA 5:2007 | Code of practice for creep/fatigue testing of cracked components |
| 03/301335 DC : DRAFT JAN 2003 | ISO 15379-2 - CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM - CATHODE BLOCKS - PART 2: DETERMINATION OF THE EXPANSION DUE TO SODIUM PENETRATION WITHOUT APPLICATION OF PRESSURE |
| ASTM E 2730 : 2010 : R2015 : EDT 2 | Standard Practice for Calibration and Use of Thermocouple Reference Junction Probes in Evaluation of Electronic Reference Junction Compensation Circuits |
| ASTM D 6200 : 2001 : R2017 | Standard Test Method for Determination of Cooling Characteristics of Quench Oils by Cooling Curve Analysis |
| BS ISO 21608:2012 | Corrosion of metals and alloys. Test method for isothermalexposure oxidation testing under high-temperature corrosion conditions for metallic materials |
| API 10 : 1990 | SPECIFICATION FOR MATERIALS AND TESTING FOR WELL CEMENTS |
| 13/30259829 DC : 0 | BS ISO 17245 - CORROSION OF METALS AND ALLOYS - TEST METHOD FOR HIGH-TEMPERATURE CORROSION TESTING OF METALLIC MATERIALS BY IMMERSING IN MOLTEN SALT OR OTHER LIQUIDS UNDER STATIC CONDITIONS |
| 03/301338 DC : DRAFT JAN 2003 | ISO 20202 - CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM - COLD AND TEPID RAMMING PASTES - PREPARATION OF BAKED TEST SPECIMENS AND DETERMINATION OF BAKING LOSS |
| BS ISO 17248:2015 | Corrosion of metals and alloys. Test method for high temperature corrosion testing of metallic materials by embedding in salt, ash, or other solids |
| ASTM D 6200 : 2001 : R2007 | Standard Test Method for Determination of Cooling Characteristics of Quench Oils by Cooling Curve Analysis |
| API 10A : 2011 | SPECIFICATION FOR CEMENTS AND MATERIALS FOR WELL CEMENTING |
| 08/30165493 DC : DRAFT FEB 2008 | BS EN ISO 10426-1 - PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 1: SPECIFICATION |
| ASTM E 585/E585M : 2012-06 | SPECIFICATION FOR COMPACTED MINERAL-INSULATED, METAL-SHEATHED, BASE METAL THERMOCOUPLE CABLE |
| ASTM F 2082 : 2015 | Standard Test Method for Determination of Transformation Temperature of Nickel-Titanium Shape Memory Alloys by Bend and Free Recovery |
| ISO 15379-2:2015 | Carbonaceous materials for the production of aluminium — Cathode block materials — Part 2: Determination of the expansion due to sodium penetration without application of pressure |
| ASTM E 228 : 2017 : REDLINE | Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer |
| AASHTO T 366 : 2017 | METHOD OF TEST FOR APPARENT VISCOSITY OF HOT-POURED ASPHALT CRACK SEALANT USING ROTATIONAL VISCOMETER |
| AASHTO TP 90 : 2010 : R2013 | METHOD OF TEST FOR MEASURING INTERFACIAL FRACTURE ENERGY OF HOT-POURED CRACK SEALANT USING A BLISTER TEST |
| ISA 67.06.01 : 2002 | PERFORMANCE MONITORING FOR NUCLEAR SAFETY-RELATED INSTRUMENT CHANNELS IN NUCLEAR POWER PLANTS |
| API 10A REDLINE : 2010 | SPECIFICATION FOR CEMENTS AND MATERIALS FOR WELL CEMENTING |
| ASTM D 4693 : 2007 | Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings |
| ASTM C 372 : 1994 : R2007 | Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by the Dilatometer Method |
| ASTM E 1159 : 2015 : REDLINE | Standard Specification for Thermocouple Materials, Platinum-Rhodium Alloys, and Platinum |
| ASTM C 621 : 2009 | Standard Test Method for Isothermal Corrosion Resistance of Refractories to Molten Glass |
| ISA MC96.1 : 1982 | TEMPERATURE MEASUREMENT THERMOCOUPLES |
| ASTM D 5110 : 1998 : R2017 | Standard Practice for Calibration of Ozone Monitors and Certification of Ozone Transfer Standards Using Ultraviolet Photometry |
| ASTM F 689 : 1997 : R2011 | Standard Practice for Determination of the Temperature of Above-Ground Plastic Gas Pressure Pipe Within Metallic Casings (Withdrawn 2017) |
| AASHTO T 48 : 2006 : R2010 | METHOD OF TEST FOR FLASH AND FIRE POINTS BY CLEVELAND OPEN CUP |
| ASTM C 436 : 1983 | Method of Test for Reheat Change of Carbon Refractory Brick and Shapes (Withdrawn 1988) |
| ASTM D 7646 : 2010 | Standard Test Method for Determination of Cooling Characteristics of Aqueous Polymer Quenchants for Aluminum Alloys by Cooling Curve Analysis |
| ASTM C 965 : 1996 : R2012 | Standard Practice for Measuring Viscosity of Glass Above the Softening Point |
| ASTM A 991/A991M : 2017 : REDLINE | Standard Test Method for Conducting Temperature Uniformity Surveys of Furnaces Used to Heat Treat Steel Products |
| ASTM E 235/E235M : 2012 : R2018 | Standard Specification for Type K and Type N Mineral-Insulated, Metal-Sheathed Thermocouples for Nuclear or for Other High-Reliability Applications |
| ASTM D 6200 : 2001 | Standard Test Method for Determination of Cooling Characteristics of Quench Oils by Cooling Curve Analysis |
| ASTM C 202 : 1993 : R2004 | Standard Test Method for Thermal Conductivity of Refractory Brick |
| ASTM C 202 : 1993 : R1998 | Standard Test Method for Thermal Conductivity of Refractory Brick |
| ASTM E 1253 : 2013 : REDLINE | Standard Guide for Reconstitution of Irradiated Charpy-Sized Specimens |
| ASTM E 207 : 2008 : R2015 : EDT 1 | Standard Test Method for Thermal EMF Test of Single Thermoelement Materials by Comparison with a Reference Thermoelement of Similar EMF-Temperature Properties |
| ASTM D 6374 : 2012 | Standard Test Method for Volatile Matter in Green Petroleum Coke Quartz Crucible Procedure |
| ASTM D 4693 : 2007 : R2017 | Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings |
| ASTM C 202 : 1993 : R2013 | Standard Test Method for Thermal Conductivity of Refractory Brick |
| ASTM E 1457 : 2015 : REDLINE | Standard Test Method for Measurement of Creep Crack Growth Times in Metals |
| ASTM C 1366 : 2004 : R2009 | Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Elevated Temperatures |
| BS EN ISO 10426-2:2003 | Petroleum and natural gas industries. Cements and materials for well cementing Testing of well cements |
| SAE J 2020 : 2016 | ACCELERATED EXPOSURE OF AUTOMOTIVE EXTERIOR MATERIALS USING A FLUORESCENT UV AND CONDENSATION APPARATUS |
| MIL-STD-1312-17 Base Document:1985 | FASTENER TEST METHODS, METHOD 17, STRESS RELATION |
| ASME BPE : 2016 | BIOPROCESSING EQUIPMENT |
| ASTM C 1211 : 2018 : REDLINE | Standard Test Method for Flexural Strength of Advanced Ceramics at Elevated Temperatures |
| ASTM C 201 : 1993 : R2013 | Standard Test Method for Thermal Conductivity of Refractories |
| API MPMS CHAPTER 19.3 PART D : 2001(R2012) | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 19.3 - EVAPORATIVE LOSS MEASUREMENT - PART D - FUGITIVE EMISSIONS TEST METHOD OF DECK-SEAM LOSS FACTORS FOR INTERNAL FLOATING-ROOF TANKS |
| ISO 17224:2015 | Corrosion of metals and alloys Test method for high temperature corrosion testing of metallic materials by application of a deposit of salt, ash, or other substances |
| BS ISO 15379-2:2015 | Carbonaceous materials for the production of aluminium. Cathode block materials Determination of the expansion due to sodium penetration without application of pressure |
| API MPM CH19.3D:2001 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 19.3 - EVAPORATIVE LOSS MEASUREMENT - PART D - FUGITIVE EMISSIONS TEST METHOD OF DECK-SEAM LOSS FACTORS FOR INTERNAL FLOATING-ROOF TANKS |
| API MPM CH19.3C : 1998(R2018) | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - EVAPORATIVE LOSS MEASUREMENT - WEIGHT LOSS TEST METHOD FOR THE MEASUREMENT OF RIM-SEAL LOSS FACTORS FOR INTERNAL FLOATING-ROOF TANKS |
| I.S. EN ISO 10426-1:2009 | PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 1: SPECIFICATION (ISO 10426-1:2009) |
| ASTM C 16 : 2003 : R2012 : EDT 2 | Standard Test Method for Load Testing Refractory Shapes at High Temperatures |
| API MPM CH19.3C : 1998(R2012) | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - EVAPORATIVE LOSS MEASUREMENT - WEIGHT LOSS TEST METHOD FOR THE MEASUREMENT OF RIM-SEAL LOSS FACTORS FOR INTERNAL FLOATING-ROOF TANKS |
| ASTM C 1465 : 2008 : R2013 | Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate Flexural Testing at Elevated Temperatures |
| ASTM C 767 : 1993 : R2013 | Standard Test Method for Thermal Conductivity of Carbon Refractories |
| API 10B-6:2010 | RECOMMENDED PRACTICE ON DETERMINING THE STATIC GEL STRENGTH OF CEMENT FORMULATIONS |
| 03/301339 DC : DRAFT JAN 2003 | ISO 14428 - CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM - COLD AND TEPID RAMMING PASTES - DETERMINATION OF EXPANSION/SHRINKAGE DURING BAKING |
| ASTM D 5110 : 1998 | Standard Practice for Calibration of Ozone Monitors and Certification of Ozone Transfer Standards Using Ultraviolet Photometry |
| ASTM E 839 : 2011 | Standard Test Methods for Sheathed Thermocouples and Sheathed Thermocouple Cable |
| ASTM F 689 : 1997 : R2004 | Standard Practice for Determination of the Temperature of Above-Ground Plastic Gas Pressure Pipe Within Metallic Casings |
| ASTM C 16 : 2003 | Standard Test Method for Load Testing Refractory Shapes at High Temperatures |
| ASTM D 6482 : 2006 | Standard Test Method for Determination of Cooling Characteristics of Aqueous Polymer Quenchants by Cooling Curve Analysis with Agitation (Tensi Method) |
| ASTM E 696 : 2007 | Standard Specification for Tungsten-Rhenium Alloy Thermocouple Wire |
| ASTM C 1465 : 2008 : R2013 : EDT 1 | Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate Flexural Testing at Elevated Temperatures |
| AASHTO T 301 : 2013 | METHOD OF TEST FOR ELASTIC RECOVERY TEST OF ASPHALT MATERIALS BY MEANS OF A DUCTILOMETER |
| ASTM C 372 : 1994 : R2001 | Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by the Dilatometer Method |
| AASHTO T 300 : 2011 | METHOD OF TEST FOR FORCE DUCTILITY TEST OF ASPHALT MATERIALS |
| ASTM C 1276 : 1994 : R2005 | Standard Test Method for Measuring the Viscosity of Mold Powders Above Their Melting Point Using a Rotational Viscometer (Withdrawn 2009) |
| ASTM E 207 : 2008 | Standard Test Method for Thermal EMF Test of Single Thermoelement Materials by Comparison with a Reference Thermoelement of Similar EMF-Temperature Properties |
| ASTM E 2714 : 2013 : REDLINE | Standard Test Method for Creep-Fatigue Testing |
| EN ISO 10426-1:2009/AC:2018 | PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 1: SPECIFICATION - TECHNICAL CORRIGENDUM 2 (ISO 10426-1:2009/COR 2:2012) |
| ASTM C 965 : 1996 : R2002 | Standard Practice for Measuring Viscosity of Glass Above the Softening Point |
| ASTM C 767 : 1993 : R1998 | Standard Test Method for Thermal Conductivity of Carbon Refractories |
| ASTM C 372 : 1994 : R2012 | Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by the Dilatometer Method |
| ISO 17245:2015 | Corrosion of metals and alloys Test method for high temperature corrosion testing of metallic materials by immersing in molten salt or other liquids under static conditions |
| ASTM C 16 : 2003 : R2008 | Standard Test Method for Load Testing Refractory Shapes at High Temperatures |
| ASTM D 4421 : 1994 : R1999 | Standard Test Method for Volatile Matter in Petroleum Coke (Withdrawn 2004) |
| ASTM E 696 : 2007 : R2013 | Standard Specification for Tungsten-Rhenium Alloy Thermocouple Wire |
| ASTM C 1862 : 2017 | Standard Test Method for the Nominal Joint Strength of End-Plug Joints in Advanced Ceramic Tubes at Ambient and Elevated Temperatures |
| ASTM D 5110 : 1998 : R2010 | Standard Practice for Calibration of Ozone Monitors and Certification of Ozone Transfer Standards Using Ultraviolet Photometry |
| ASTM E 2730 : 2010 : R2015 : EDT 1 | Standard Practice for Calibration and Use of Thermocouple Reference Junction Probes in Evaluation of Electronic Reference Junction Compensation Circuits |
| ASTM C 417 : 2005 : R2015 | Standard Test Method for Thermal Conductivity of Unfired Monolithic Refractories |
| ASTM D 5249 : 2010 : R2016 | Standard Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland-Cement Concrete and Asphalt Joints |
| ASTM E 2368 : 2010 | Standard Practice for Strain Controlled Thermomechanical Fatigue Testing |
| ISO 14428:2005 | Carbonaceous materials for the production of aluminium Cold and tepid ramming pastes Expansion/shrinkage during baking |
| ASTM D 345 : 2002 | Side bearings of the freight wagon bogies. General specifications |
| ISO 10426-6:2008 | Petroleum and natural gas industries — Cements and materials for well cementing — Part 6: Methods for determining the static gel strength of cement formulations |
| ASTM D 3466 : 2006 : R2011 | Standard Test Method for Ignition Temperature of Granular Activated Carbon |
| ASTM F 689 : 1997 | Standard Practice for Determination of the Temperature of Above-Ground Plastic Gas Pressure Pipe Within Metallic Casings |
| ASTM C 1276 : 1994 : R1999 | Standard Test Method for Measuring the Viscosity of Mold Powders Above Their Melting Point Using a Rotational Viscometer |
| ISO 10426-1:2009 | Petroleum and natural gas industries Cements and materials for well cementing Part 1: Specification |
| I.S. EN ISO 10426-6:2008 | PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 6: METHODS FOR DETERMINING THE STATIC GEL STRENGTH OF CEMENT FORMULATIONS |
| 03/301334 DC : DRAFT JAN 2003 | ISO 15379-1 - CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM - CATHODE BLOCKS - PART 1: DETERMINATION OF THE EXPANSION DUE TO SODIUM PENETRATION WITH APPLICATION OF PRESSURE |
| ASTM C 1465 : 2008 | Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate Flexural Testing at Elevated Temperatures |
| SAE ARP 5144 : 2017 | HEAT APPLICATION FOR THERMOSETTING RESIN CURING |
| ASTM D 5110 : 1998 : R2004 | Standard Practice for Calibration of Ozone Monitors and Certification of Ozone Transfer Standards Using Ultraviolet Photometry |
| 13/30259880 DC : 0 | BS ISO 17224 - CORROSION OF METALS AND ALLOYS - TEST METHOD FOR HIGH-TEMPERATURE CORROSION TESTING OF METALLIC MATERIALS BY APPLICATION OF A DEPOSIT OF SALT, ASH OR OTHER SUBSTANCES |
| BS ISO 17224:2015 | Corrosion of metals and alloys. Test method for high temperature corrosion testing of metallic materials by application of a deposit of salt, ash, or other substances |
| BS EN ISO 10426-6:2008 | Petroleum and natural gas industries. Cements and materials for well cementing Methods for determining the static gel strength of cement formulations (ISO 10426-6:2008) |
| API MPM CH19.3C : 1998 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - EVAPORATIVE LOSS MEASUREMENT - WEIGHT LOSS TEST METHOD FOR THE MEASUREMENT OF RIM-SEAL LOSS FACTORS FOR INTERNAL FLOATING-ROOF TANKS |
| ASTM D 6200 : 2001 : R2012 | Standard Test Method for Determination of Cooling Characteristics of Quench Oils by Cooling Curve Analysis |
| ASTM E 289 : 2017 : REDLINE | Standard Test Method for Linear Thermal Expansion of Rigid Solids with Interferometry |
| ISO 21608:2012 | Corrosion of metals and alloys — Test method for isothermal-exposure oxidation testing under high-temperature corrosion conditions for metallic materials |
| ASTM D 6549 : 2006 : R2011 | Standard Test Method for Determination of Cooling Characteristics of Quenchants by Cooling Curve Analysis with Agitation (Drayton Unit) |
| ASTM C 767 : 1993 : R2009 | Standard Test Method for Thermal Conductivity of Carbon Refractories |
| ASTM E 608/E608M : 2013 : REDLINE | SPECIFICATION FOR MINERAL-INSULATED, METAL-SHEATHED BASE METAL THERMOCOUPLES |
| ASTM D 1676 : 2017 : REDLINE | Standard Test Methods for Film-Insulated Magnet Wire |
| ASTM D 5249 : 2010 | Standard Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland-Cement Concrete and Asphalt Joints |
| ASTM F 2082/F2082M : 2016 : REDLINE | Standard Test Method for Determination of Transformation Temperature of Nickel-Titanium Shape Memory Alloys by Bend and Free Recovery |
| AASHTO T 240 : 2013 | METHOD OF TEST FOR EFFECT OF HEAT AND AIR ON A MOVING FILM OF ASPHALT BINDER (ROLLING THIN-FILM OVEN TEST) |
| ASTM C 1337 : 2017 : REDLINE | Standard Test Method for Creep and Creep Rupture of Continuous Fiber-Reinforced Advanced Ceramics Under Tensile Loading at Elevated Temperatures |
| ASTM E 1530 : 2011 | Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique |
| API 10A CHINESE : 2002 | SPECIFICATION FOR CEMENTS AND MATERIALS FOR WELL CEMENTING |
| AASHTO T 48 : 2006 : R2015 | METHOD OF TEST FOR FLASH AND FIRE POINTS BY CLEVELAND OPEN CUP |
| ASTM C 182 : 1988 : R2013 | Standard Test Method for Thermal Conductivity of Insulating Firebrick |
| ASTM D 6374 : 2012 : R2017 : EDT 1 | Standard Test Method for Volatile Matter in Green Petroleum Coke Quartz Crucible Procedure |
| ASTM C 965 : 1996 | Standard Practice for Measuring Viscosity of Glass Above the Softening Point |
| AASHTO T 313 : 2012 | METHOD OF TEST FOR DETERMINING THE FLEXURAL CREEP STIFFNESS OF ASPHALT BINDER USING THE BENDING BEAM RHEOMETER (BBR) |
| ASTM D 6482 : 2006 : R2016 | Standard Test Method for Determination of Cooling Characteristics of Aqueous Polymer Quenchants by Cooling Curve Analysis with Agitation (Tensi Method) |
| AASHTO T 78 : 2015 | METHOD OF TEST FOR DISTILLATION OF CUTBACK ASPHALT PRODUCTS |
| ASTM D 6549 : 2006 : R2015 | Standard Test Method for Determination of Cooling Characteristics of Quenchants by Cooling Curve Analysis with Agitation (Drayton Unit) |
| ASTM D 6482 : 2006 : R2011 | Standard Test Method for Determination of Cooling Characteristics of Aqueous Polymer Quenchants by Cooling Curve Analysis with Agitation (Tensi Method) |
| ASTM C 965 : 1996 : R2017 | Standard Practice for Measuring Viscosity of Glass Above the Softening Point |
| ASTM C 1366 : 2004 : R2013 | Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Elevated Temperatures |
| ASTM D 5207 : 2014 : REDLINE | Standard Practice for Confirmation of 20–mm (50–W) and 125–mm (500–W) Test Flames for Small-Scale Burning Tests on Plastic Materials |
| ASTM E 2846 : 2014-10 | GUIDE FOR THERMOCOUPLE VERIFICATION |
| ASTM D 447 : 1993 | Test Method for Distillation of Plant Spray Oils (Withdrawn 1997) |
| ASTM D 243/D243M : 2014 : REDLINE | Standard Test Method for Residue of Specified Penetration |
| UNI EN ISO 10426-2 : 2006 | PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 2: TESTING OF WELL CEMENTS |
| UNI EN ISO 10426-1 : 2010 | PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 1: SPECIFICATION |
| ASTM C 201 : 1993 : R2004 | Standard Test Method for Thermal Conductivity of Refractories |
| ASTM G 179 : 2004 | Standard Specification for Metal Black Panel and White Panel Temperature Devices for Natural Weathering Tests |
| ASTM D 3026 : 1994 | Standard Test Method for Sinter Index of Electrical Grade Magnesium Oxide for Use in Sheathed Heating Elements (Withdrawn 2002) |
| 10/30217198 DC : 0 | BS EN ISO 10426-2 - PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 2: TESTING OF WELL CEMENTS |
| ASTM E 235/E235M : 2012 | Standard Specification for Type K and Type N Mineral-Insulated, Metal-Sheathed Thermocouples for Nuclear or for Other High-Reliability Applications |
| CSA A23.1 A23.2 : 2014 | CONCRETE MATERIALS AND METHODS OF CONCRETE CONSTRUCTION/TEST METHODS AND STANDARD PRACTICES FOR CONCRETE |
| API MPM CH19.3A : 1997(R2012) | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 19.3 - EVAPORATIVE LOSS MEASUREMENT - PART A - WIND TUNNEL TEST METHOD FOR THE MEASUREMENT OF DECK-FITTING LOSS FACTORS FOR EXTERNAL FLOATING-ROOF TANKS |
| ASTM C 16 : 2003 : R2012 | Standard Test Method for Load Testing Refractory Shapes at High Temperatures |
| 10/30231379 DC : 0 | BS ISO 21608 - CORROSION OF METALS AND ALLOYS - TEST METHOD FOR ISOTHERMAL-EXPOSURE OXIDATION TESTING UNDER HIGH-TEMPERATURE CORROSION CONDITIONS FOR METALLIC MATERIALS |
| ASTM D 3466 : 2006 | Standard Test Method for Ignition Temperature of Granular Activated Carbon |
| MIL-DTL-25446 Revision E:2012 | Transmitter, Temperature, Electrical Resistance, Armored, Bayonet Locking Type, (-50 Degrees C to 300 Degrees C) |
| ASTM E 633 : 2013 : REDLINE | Standard Guide for Use of Thermocouples in Creep and Stress-Rupture Testing to 1800°F (1000°C) in Air |
| ISO 15379-1:2015 | Carbonaceous materials for the production of aluminium Cathode block materials Part 1: Determination of the expansion due to sodium penetration with application of pressure |
| ASTM E 2730 : 2010 | Standard Practice for Calibration and Use of Thermocouple Reference Junction Probes in Evaluation of Electronic Reference Junction Compensation Circuits |
| ASTM C 16 : 2003 : R2008 : EDT 1 | Standard Test Method for Load Testing Refractory Shapes at High Temperatures |
| BS ISO 14428:2004 | Carbonaceous materials for the production of aluminium. Cold and tepid ramming pastes. Expansion/shrinkage during baking |
| BS ISO 15379-1:2015 | Carbonaceous materials for the production of aluminium. Cathode block materials Determination of the expansion due to sodium penetration with application of pressure |
| AASHTO TP 85 : 2010 : R2013 | METHOD OF TEST FOR APPARENT VISCOSITY OF HOT-POURED BITUMINOUS CRACK SEALANT USING BROOKFIELD ROTATIONAL VISCOMETER RV SERIES INSTRUMENT |
| ASTM E 696 : 2007 : R2018 | Standard Specification for Tungsten-Rhenium Alloy Thermocouple Wire |
| ASTM C 182 : 1988 : R2004 | Standard Test Method for Thermal Conductivity of Insulating Firebrick |
| TR AMS2750 : 2009 | AEROSPACE SERIES - AEROSPACE MATERIAL SPECIFICATION - PYROMETRY |
| AASHTO TP 85 : 2010 : R2015 | METHOD OF TEST FOR APPARENT VISCOSITY OF HOT-POURED BITUMINOUS CRACK SEALANT USING BROOKFIELD ROTATIONAL VISCOMETER RV SERIES INSTRUMENT |
| ASTM C 182 : 1988 : R2009 | Standard Test Method for Thermal Conductivity of Insulating Firebrick |
| AASHTO TP 90 : 2010 : R2015 | METHOD OF TEST FOR MEASURING INTERFACIAL FRACTURE ENERGY OF HOT-POURED CRACK SEALANT USING A BLISTER TEST |
| API 10B-6 : 2010 : R2015 | RECOMMENDED PRACTICE ON DETERMINING THE STATIC GEL STRENGTH OF CEMENT FORMULATIONS |
| ASTM C 417 :2005 | Standard Test Method for Thermal Conductivity of Unfired Monolithic Refractories |
| BS EN ISO 10426-1:2009 | Petroleum and natural gas industries. Cements and materials for well cementing Specification |
| ASTM E 601 : 2015 : REDLINE | Standard Guide for Measuring Electromotive Force (emf) Stability of Base-Metal Thermoelement Materials with Time in Air |
| ASTM C 372 : 1994 : R2001 : EDT 1 | Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by the Dilatometer Method |
| ASTM C 1099 : 2007 : R2012 | Standard Test Method for Modulus of Rupture of Carbon-Containing Refractory Materials at Elevated Temperatures |
| ASTM C 201 : 1993 : R2019 | Standard Test Method for Thermal Conductivity of Refractories |
| ASTM C 1099 : 2007 | Standard Test Method for Modulus of Rupture of Carbon-Containing Refractory Materials at Elevated Temperatures |
| ASTM C 202 : 1993 : R2009 : EDT 1 | Standard Test Method for Thermal Conductivity of Refractory Brick |
| ASTM C 417 : 2005 : R2010 : EDT 1 | Standard Test Method for Thermal Conductivity of Unfired Monolithic Refractories |
| ASTM D 402/D402M : 2014 : REDLINE | Standard Test Method for Distillation of Cutback Asphalt (Withdrawn 2023) |
| ASTM E 2760 : 2016 : REDLINE | Standard Test Method for Creep-Fatigue Crack Growth Testing |
| ASTM E 1232 : 2007 : R2013 | Standard Test Method for Temperature Limit of Flammability of Chemicals |
| ASTM C 1291 : 2018 : REDLINE | Standard Test Method for Elevated Temperature Tensile Creep Strain, Creep Strain Rate, and Creep Time to Failure for Monolithic Advanced Ceramics |
| ASTM D 7646 : 2010 : R2014 | Standard Test Method for Determination of Cooling Characteristics of Aqueous Polymer Quenchants for Aluminum Alloys by Cooling Curve Analysis |
| ASTM E 1232 : 2007 | Standard Test Method for Temperature Limit of Flammability of Chemicals |
| ASTM E 1333 : 2014 : REDLINE | Standard Test Method for Determining Formaldehyde Concentrations in Air and Emission Rates from Wood Products Using a Large Chamber |
| ISO 20202:2004 | Carbonaceous materials used in the production of aluminium — Cold and tepid ramming pastes — Preparation of baked test pieces and determination of loss on baking |
| ISO 10426-2:2003 | Petroleum and natural gas industries — Cements and materials for well cementing — Part 2: Testing of well cements |
| EN ISO 10426-6:2008 | Petroleum and natural gas industries - Cements and materials for well cementing - Part 6: Methods for determining the static gel strength of cement formulations (ISO 10426-6:2008) |
| ASTM E 608/E608M : 2013 : R2019 | Standard Specification for Mineral-Insulated, Metal-Sheathed Base Metal Thermocouples |
| ASTM C 24 : 2009 | Standard Test Method for Pyrometric Cone Equivalent (PCE) of Fireclay and High Alumina Refractory Materials |
| BS ISO 17245:2015 | Corrosion of metals and alloys. Test method for high temperature corrosion testing of metallic materials by immersing in molten salt or other liquids under static conditions |
| ISO 13573:2012 | Corrosion of metals and alloys — Test method for thermal-cycling exposure testing under high-temperature corrosion conditions for metallic materials |
| ASTM C 372 : 1994 : R2016 | Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by the Dilatometer Method |
| ASTM C 372 : 1994 | Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by the Dilatometer Method |
| 11/30210857 DC : 0 | BS ISO 13573 - CORROSION OF METALS AND ALLOYS - TEST METHOD FOR THERMAL-CYCLING EXPOSURE TESTING UNDER HIGH-TEMPERATURE CORROSION CONDITIONS FOR METALLIC MATERIALS |
| 13/30259830 DC : 0 | BS ISO 17248 - CORROSION OF METALS AND ALLOYS - TEST METHOD FOR HIGH-TEMPERATURE CORROSION TESTING OF METALLIC MATERIALS BY EMBEDDING IN SALT, ASH, OR OTHER SOLIDS |
| BS ISO 20202:2004 | Carbonaceous materials used in the production of aluminium. Cold and tepid ramming pastes. Preparation of baked test pieces and determination of loss on baking |
| ASTM D 6084/D6084M : 2013-12 | TEST METHOD FOR ELASTIC RECOVERY OF ASPHALT MATERIALS BY DUCTILOMETER |
| ASTM C 201 : 1993 : R1998 | Standard Test Method for Thermal Conductivity of Refractories |
| ASTM C 38 : 1989 | Method for Panel Spalling Testing Refractory Brick (Withdrawn 1994) |
| ASTM C 16 : 2003 : R2012 : EDT 1 | Standard Test Method for Load Testing Refractory Shapes at High Temperatures |
| MIL-P-11570 Revision C:1984 | PYROMETERS, INDICATING, THERMOCOUPLES |
| AASHTO R 28 : 2012 | PRACTICE FOR ACCELERATED AGING OF ASPHALT BINDER USING A PRESSURIZED AGING VESSEL (PAV) |
| ASTM C 621 : 2009 : R2014 | Standard Test Method for Isothermal Corrosion Resistance of Refractories to Molten Glass |
| ASTM G 179 : 2004 : R2011 | Standard Specification for Metal Black Panel and White Panel Temperature Devices for Natural Weathering Tests |
| ASTM C 201 : 1993 : R2009 | Standard Test Method for Thermal Conductivity of Refractories |
| SAE AS 7101 : 2007 | NATIONAL AEROSPACE AND DEFENSE CONTRACTORS ACCREDITATION PROGRAM (NADCAP) GENERAL REQUIREMENTS FOR MATERIALS TEST LABORATORY ACCREDITATION PROGRAM |
| AASHTO TP 89 : 2010 : R2013 | METHOD OF TEST FOR MEASURING ADHESION OF HOT-POURED CRACK SEALANT USING DIRECT ADHESION TESTER |
| AASHTO TP 89 : 2010 : R2015 | METHOD OF TEST FOR MEASURING ADHESION OF HOT-POURED CRACK SEALANT USING DIRECT ADHESION TESTER |
| SAE AMS 2750 : 2012 | PYROMETRY |
| ASTM E 2368 : 2010 : R2017 | Standard Practice for Strain Controlled Thermomechanical Fatigue Testing |
| API MPM CH19.3A : 1997 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 19.3 - EVAPORATIVE LOSS MEASUREMENT - PART A - WIND TUNNEL TEST METHOD FOR THE MEASUREMENT OF DECK-FITTING LOSS FACTORS FOR EXTERNAL FLOATING-ROOF TANKS |
| ASTM E 2181/E2181M : 2011 | Standard Specification for Compacted Mineral-Insulated, Metal-Sheathed, Noble Metal Thermocouples and Thermocouple Cable |
| ASTM D 6549 : 2006 | Standard Test Method for Determination of Cooling Characteristics of Quenchants by Cooling Curve Analysis with Agitation (Drayton Unit) |
| API MPM CH19.3A : 1997 : R2007 | MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 19.3 - EVAPORATIVE LOSS MEASUREMENT - PART A - WIND TUNNEL TEST METHOD FOR THE MEASUREMENT OF DECK-FITTING LOSS FACTORS FOR EXTERNAL FLOATING-ROOF TANKS |
| UNI EN ISO 10426-6 : 2009 | PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 6: METHODS FOR DETERMINING THE STATIC GEL STRENGTH OF CEMENT FORMULATION |
| ASTM E 2584 : 2014 : REDLINE | Standard Practice for Thermal Conductivity of Materials Using a Thermal Capacitance (Slug) Calorimeter |
| ASTM D 4693 : 2007 : R2012 | Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings |
| ASTM C 182 : 1988 : R1998 | Standard Test Method for Thermal Conductivity of Insulating Firebrick |
| ASTM C 965 : 1996 : R2007 | Standard Practice for Measuring Viscosity of Glass Above the Softening Point |
| ASTM C 24 : 2009 : R2018 | Standard Test Method for Pyrometric Cone Equivalent (PCE) of Fireclay and High-Alumina Refractory Materials |
| ASTM C 16 : 2003 : R2018 | Standard Test Method for Load Testing Refractory Shapes at High Temperatures |
| ASTM C 583 : 2015 : REDLINE | Standard Test Method for Modulus of Rupture of Refractory Materials at Elevated Temperatures |
| ASTM C 1834 : 2016 | Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress Flexural Testing (Stress Rupture) at Elevated Temperatures |
| ASTM C 767 : 1993 : R2004 | Standard Test Method for Thermal Conductivity of Carbon Refractories |
| ISO 17248:2015 | Corrosion of metals and alloys Test method for high temperature corrosion testing of metallic materials by embedding in salt, ash, or other solids |
| ASTM D 6723 : 2012 | Standard Test Method for Determining the Fracture Properties of Asphalt Binder in Direct Tension (DT) (Withdrawn 2021) |
| ASTM C 1099 : 2007 : R2019 | Standard Test Method for Modulus of Rupture of Carbon-Containing Refractory Materials at Elevated Temperatures |
| ASTM D 113 : 2017 | Standard Test Method for Ductility of Asphalt Materials |
| ASTM E 1232 : 2007 : R2019 | Standard Test Method for Temperature Limit of Flammability of Chemicals |
| ASTM E 1530 : 2011 : R2016 | Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique |
| ASTM E 839 : 2011 : R2016 : EDT 1 | Standard Test Methods for Sheathed Thermocouples and Sheathed Thermocouple Cable |
| ASTM E 344 : 2016-12 | TERMINOLOGY RELATING TO THERMOMETRY AND HYDROMETRY |
| ASTM C 1366 : 2004 | Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Elevated Temperatures |
| ASTM E 207 : 2008 : R2015 | Standard Test Method for Thermal EMF Test of Single Thermoelement Materials by Comparison with a Reference Thermoelement of Similar EMF-Temperature Properties |
| EN ISO 10426-2:2003/AC:2007 | Petroleum and natural gas industries - Cements and materials for well cementing - Part 2: Testing of well cements (ISO 10426-2:2003/Cor 1:2006) |
| ASTM E 230 : 2003 | Standard Specification and Temperature-Electromotive Force (EMF) Tables for Standardized Thermocouples |
| ASTM E 1 : 2014 : REDLINE | Standard Specification for ASTM Liquid-in-Glass Thermometers |
| ASTM E 2846 : 2014-10 | GUIDE FOR THERMOCOUPLE VERIFICATION |
| ASTM E 1594 : 2016 : REDLINE | Standard Guide for Expression of Temperature |
| ASTM E 644 : 2011 : REDLINE | Standard Test Methods for Testing Industrial Resistance Thermometers |
| ASTM E 344 : 2016-12 | TERMINOLOGY RELATING TO THERMOMETRY AND HYDROMETRY |
| ASTM E 1751 : 2000 | Standard Guide for Temperature Electromotive Force (emf) Tables for Non-Letter Designated Thermocouple Combinations (Withdrawn 2009) |
$135.86
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.