Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 2965 : 2017

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Determination of Low Levels of Heat Release Rate for Materials and Products Using an Oxygen Consumption Calorimeter
Available format(s)

Hardcopy , PDF

Superseded date

17-06-2022

Language(s)

English

Published date

11-08-2017

1.1This fire-test-response standard provides a procedure for measuring the response of materials that emit low levels of heat release when exposed to controlled levels of radiant heating with or without an external igniter.

1.2This test method differs from Test Method E1354 in that it prescribes a different specific test specimen size, specimen holder, test specimen orientation, a direct connection between the plenum and the top plate of the cone heater assembly to ensure complete collection of all the combustion gases (Fig. 1), and a lower volumetric flow rate for analyses via oxygen consumption calorimetry. It is intended for use on materials and products that contain only small amounts of combustible ingredients or components, such as test specimens that yield a peak heat release of <200 kW/m2 and total heat release of <15 MJ/m2.

Note 1:PMMA is typically used to check the general operation of a Cone Calorimeter. PMMA should not be used with this standard as the heat release rate is too high.

1.3The rate of heat release is determined by measurement of the oxygen consumption as determined by the oxygen concentration and the flow rate in the exhaust product stream. The effective heat of combustion is determined from a concomitant measurement of test specimen mass loss rate, in combination with the heat release rate. Smoke development (an optional measurement) is measured by obscuration of light by the combustion product stream.

1.4Test specimens shall be exposed to initial test heat fluxes generated by a conical radiant heater. External ignition, when used, shall be by electric spark. The test specimen testing orientation is horizontal, independent of whether the end-use application involves a horizontal or a vertical orientation.

1.5Ignitability is determined as a measurement of time from initial exposure to time of sustained flaming.

1.6This test method has been developed for use for material and product evaluations, mathematical modeling, design purposes, and development and research. Examples of material test specimens include portions of an end-use product or the various components used in the end-use product.

1.7The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.8This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.

1.9Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.

1.10This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.

1.11This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
E 05
DocumentType
Test Method
Pages
13
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 6113 : 2021 Standard Test Method for Using Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables
ASTM E 2067 : 2020 Standard Practice for Full-Scale Oxygen Consumption Calorimetry Fire Tests
ASTM D 6113 : 2016 Standard Test Method for Using a Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables

ASTM E 1354 : 2010 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1354 : 2002 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1354 : 2014 : EDT 1 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 5865 : 2011 : REV A Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM E 1354 : 2004 : REV A Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1354 : 1999 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1354 : 2010 : REV A Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1354 : 2003 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 5865 : 2004 Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM E 1354 : 2002 : REV D : EDT 1 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 5865 : 2000 Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM D 5865 : 2013 Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM E 1354 : 2008 : REV A Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 5865 : 2007 : REV A Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM D 5865 : 2003 Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM E 176 : 2018 : REV A : EDT 1 Standard Terminology of Fire Standards
ASTM E 1354 : 2002 : REV D Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 5865 : 1998 : REV A Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM D 5865 : 2003 : REV A Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM D 5865 : 1999 : REV A Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM E 1354 : 2009 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 5865 : 2011 Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM E 1354 : 2015 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1354 : 2016 : REV A Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 176 : 2021 Standard Terminology of Fire Standards
ASTM D 5865 : 2012 Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM E 176 : 2018 : REV A : EDT 2 Standard Terminology of Fire Standards
ASTM E 1354 : 2016 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1354 : 2017 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1354 : 2002 : REV A Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 5865 : 2001 : REV A Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM E 1354 : 2015 : REV A Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 5865 : 2001 : REV A : EDT 1 Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM E 1354 : 2011 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1354 : 2011 : REV B Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 5865 : 2010 : REV A Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM E 1354 : 2011 : REV A Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 5865 : 2007 Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM D 5865 : 2002 Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM D 5865 : 2001 Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM E 176 : 2021 : REV A Standard Terminology of Fire Standards
ASTM E 1354 : 2004 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1354 : 2013 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1354 : 2014 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 5865 : 2010 : REV A : EDT 1 Standard Test Method for Gross Calorific Value of Coal and Coke
ASTM D 5865 : 2010 Standard Test Method for Gross Calorific Value of Coal and Coke

View more information
$135.86
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more