Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 3081 : 2016

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Outlier Screening Using Process Compensated Resonance Testing via Swept Sine Input for Metallic and Non-Metallic Parts
Available format(s)

Hardcopy , PDF

Superseded date

13-08-2021

Language(s)

English

Published date

09-01-2017

CONTAINED IN VOL. 03.04, 2017 Specifies a general procedure for using the process compensated resonance testing (PCRT) via swept sine input method to perform outlier screening on populations of newly manufactured and in-service parts.

1.1This practice describes a general procedure for using the process compensated resonance testing (PCRT) via swept sine input method to perform outlier screening on populations of newly manufactured and in-service parts. PCRT excites the resonance frequencies of metallic and non-metallic test components using a swept sine wave input over a set frequency range. PCRT detects and analyzes component resonance frequency patterns, and uses the differences in resonance patterns between acceptable and unacceptable components to perform non-destructive testing. PCRT frequency analysis compares the resonance pattern of a component to the patterns of known acceptable and unacceptable populations of the same component, and renders a pass or fail result based on the similarity of the tested component to those populations. For non-destructive testing applications with known defects or material states of interest, or both, Practice E2534 covers the development and application of PCRT sorting modules that compare test components to known acceptable and unacceptable component populations. However, some applications do not have physical examples of components with known defects or material states. Other applications experience isolated component failures with unknown causes or causes that propagate from defects that are beyond the sensitivity of the current required inspections, or both. In these cases, PCRT is applied in an outlier screening mode that develops a sorting module using only a population of presumed acceptable production components, and then compares test components for similarity to that presumed acceptable population. The resonance differences can be used to distinguish acceptable components with normal process variation from outlier components that may have material states or defects, or both, that will cause performance deficiencies. These material states and defects include, but are not limited to, cracks, voids, porosity, shrink, inclusions, discontinuities, grain and crystalline structure differences, density-related anomalies, heat treatment variations, material elastic property differences, residual stress, and dimensional variations. This practice is intended for use with instruments capable of exciting, measuring, recording, and analyzing multiple, whole body, mechanical vibration resonance frequencies in acoustic or ultrasonic frequency ranges, or both.

1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 7 on Hazards.

Committee
E 07
DocumentType
Standard Practice
Pages
9
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM E 2001 : 2018 Standard Guide for Resonant Ultrasound Spectroscopy for Defect Detection in Both Metallic and Non-metallic Parts
ASTM E 3213 : 2019 Standard Practice for Part-to-Itself Examination Using Process Compensated Resonance Testing Via Swept Sine Input for Metallic and Non-Metallic Parts
ASTM E 2534 : 2020 Standard Practice for Targeted Defect Detection Using Process Compensated Resonance Testing Via Swept Sine Input for Metallic and Non-Metallic Parts

ASTM E 1316 : 2011 : REV B Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2015 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 2534 : 2010 Standard Practice for Process Compensated Resonance Testing Via Swept Sine Input for Metallic and Non-Metallic Parts
ASTM E 1316 : 2009 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2008 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2010 : REV C Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2020 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2017 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2013 : REV C Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2000 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2019 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2014 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2013 : REV B Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2018 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2011 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 2001 : 2008 Standard Guide for Resonant Ultrasound Spectroscopy for Defect Detection in Both Metallic and Non-Metallic Parts
ASTM E 1316 : 2007 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2015 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2019 : REV B Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2013 : REV D Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2000 Standard Terminology for Nondestructive Examinations
ASTM E 2001 : 1998 Standard Guide for Resonant Ultrasound Spectroscopy for Defect Detection in Both Metallic and Non-Metallic Parts
ASTM E 1316 : 2019 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2001 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2003 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2018 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2006 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2016 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2002 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2014 : EDT 1 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2010 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 2001 : 2013 Standard Guide for Resonant Ultrasound Spectroscopy for Defect Detection in Both Metallic and Non-metallic Parts
ASTM E 1316 : 2013 Standard Terminology for Nondestructive Examinations
ASTM E 2001 : 2018 Standard Guide for Resonant Ultrasound Spectroscopy for Defect Detection in Both Metallic and Non-metallic Parts
ASTM E 1316 : 2017 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2016 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2009 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2002 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2004 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2007 : REV C Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2010 : REV B Standard Terminology for Nondestructive Examinations
ASTM E 2534 : 2015 Standard Practice for Process Compensated Resonance Testing Via Swept Sine Input for Metallic and Non-Metallic Parts
ASTM E 1316 : 2013 : REV A Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2021 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2007 : REV B Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2005 Standard Terminology for Nondestructive Testing
ASTM E 1316 : 2004 Standard Terminology for Nondestructive Examinations
ASTM E 1316 : 2007 Standard Terminology for Nondestructive Examinations
ASTM E 2534 : 2015 : REDLINE Standard Practice for Process Compensated Resonance Testing Via Swept Sine Input for Metallic and Non-Metallic Parts
ASTM E 1316 : 2012 Standard Terminology for Nondestructive Examinations

View more information
$122.77
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more