Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 777 : 2017 : REV A

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Carbon and Hydrogen in the Analysis Sample of Refuse-Derived Fuel
Available format(s)

Hardcopy , PDF

Superseded date

20-04-2023

Language(s)

English

Published date

15-12-2017

CONTAINED IN VOL. 11.04, 2017 Defines the determination of total carbon and hydrogen in a sample of refuse-derived fuel (RDF).

1.1This test method is for the determination of total carbon and hydrogen in a sample of refuse-derived fuel (RDF). Both carbon and hydrogen are determined in one analysis. This test method yields the total percentages of carbon and hydrogen in RDF as analyzed and the results include not only carbon and hydrogen in the organic matter, but also the carbon present in mineral carbonates and the hydrogen present in the free moisture accompanying the analysis sample as well as hydrogen present as water of hydration.

Note 1:It is recognized that certain technical applications of the data derived from this test procedure may justify additional corrections. These corrections could involve compensation for the carbon present as carbonates, the hydrogen of free moisture accompanying the analysis sample, and the calculated hydrogen present as water of hydration.

1.2This test method may be applicable to any waste material from which a laboratory analysis sample can be prepared.

1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 8.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 34
DocumentType
Test Method
Pages
5
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM E 2779 : 2010 : R2017 Standard Test Method for Determining Particulate Matter Emissions from Pellet Heaters
ASTM E 870 : 1982 : R2019 Standard Test Methods for Analysis of Wood Fuels

ASTM D 5681 : 2017 Standard Terminology for Waste and Waste Management
ASTM E 791 : 2008 : R2016 Standard Test Method for Calculating Refuse-Derived Fuel Analysis Data from As-Determined to Different Bases
ASTM D 5681 : 2008 Standard Terminology for Waste and Waste Management
ASTM D 5681 : 2018 Standard Terminology for Waste and Waste Management
ASTM D 1193 : 1977 : R1983 : EDT 1 Standard Specification for Reagent Water
ASTM E 790 : 2015 : REDLINE Standard Test Method for Residual Moisture in Refuse-Derived Fuel Analysis Samples
ASTM E 790 : 2015 Standard Test Method for Residual Moisture in Refuse-Derived Fuel Analysis Samples
ASTM D 5681 : 1998 : REV A Standard Terminology for Waste and Waste Management
ASTM D 5681 : 2016 Standard Terminology for Waste and Waste Management
ASTM D 1193 : 2006 : R2011 Standard Specification for Reagent Water
ASTM D 5681 : 2009 Standard Terminology for Waste and Waste Management
ASTM E 790 : 2021 Standard Test Method for Residual Moisture in Refuse-Derived Fuel Analysis Samples
ASTM E 829 : 2023 Standard Practice for Preparing Refuse-Derived Fuel (RDF) Laboratory Samples for Analysis
ASTM D 1193 : 1991 Standard Specification for Reagent Water
ASTM D 5681 : 1998 : REV A : EDT 1 Standard Terminology for Waste and Waste Management
ASTM D 5681 : 1998 : REV A : R2004 Standard Terminology for Waste and Waste Management
ASTM D 5681 : 2016 : REV A Standard Terminology for Waste and Waste Management
ASTM D 5681 : 1998 : REV A : R2004 : EDT 1 Standard Terminology for Waste and Waste Management
ASTM D 5681 : 2020 Standard Terminology for Waste and Waste Management
ASTM E 829 : 2016 Standard Practice for Preparing Refuse-Derived Fuel (RDF) Laboratory Samples for Analysis
ASTM E 791 : 2008 : R2022 Standard Test Method for Calculating Refuse-Derived Fuel Analysis Data from As-Determined to Different Bases
ASTM D 1193 : 1970 Standard Specification For Reagent Water
ASTM D 5681 : 2022 Standard Terminology for Waste and Waste Management
ASTM D 1193 : 2006 Standard Specification for Reagent Water
ASTM D 1193 : 1999 Standard Specification for Reagent Water
ASTM D 5681 : 2022 : EDT 1 Standard Terminology for Waste and Waste Management
ASTM D 1193 : 2006 : R2018 Standard Specification for Reagent Water
ASTM D 5681 : 2013 Standard Terminology for Waste and Waste Management
ASTM D 5681 : 2017-09 TERMINOLOGY FOR WASTE AND WASTE MANAGEMENT

View more information
$122.77
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more