Customer Support: 131 242

i2i Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search

ASTM F 1743 : 2017 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Rehabilitation of Existing Pipelines and Conduits by Pulled-in-Place Installation of Cured-in-Place Thermosetting Resin Pipe (CIPP)
Available format(s)

PDF

Superseded date

21-01-2022

Language(s)

English

Published date

01-02-2017

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 08.04, 2018 Specifies the procedures for the reconstruction of pipelines and conduits (4 to 96 in. (10 to 244 cm) diameter) by the pulled-in-place installation of a resin-impregnated, flexible fabric tube into an existing conduit and secondarily inflated through the inversion of a calibration hose by the use of a hydrostatic head or air pressure.

1.1This practice describes the procedures for the reconstruction of pipelines and conduits (2 to 96 in. (5 to 244 cm) diameter) by the pulled-in-place installation of a resin-impregnated, flexible fabric tube into an existing conduit and secondarily inflated through the inversion of a calibration hose by the use of a hydrostatic head or air pressure (see Fig. 1). The resin is cured by circulating hot water or by the introduction of controlled steam into the tube. When cured, the finished cured-in-place pipe will be continuous and tight fitting. This reconstruction process may be used in a variety of gravity and pressure applications such as sanitary sewers, storm sewers, process piping, electrical conduits, and ventilation systems.

1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Note 1:There are no ISO standards covering the primary subject matter of this practice.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
F 17
DocumentType
Redline
Pages
9
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

03/102086 DC : DRAFT JAN 2003 BS ISO 16241 - NOTCH TENSILE TEST TO MEASURE THE RESISTANCE TO SLOW CRACK GROWTH OF POLYETHYLENE MATERIALS FOR PIPES AND FITTING PRODUCTS (PENT)
ASTM F 3240 : 2017 Standard Practice for Installation of Seamless Molded Hydrophilic Gaskets (SMHG) for Long-Term Watertightness of Cured-in-Place Rehabilitation of Main and Lateral Pipelines
ASTM D 5813 : 2004 : R2008 Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
ASTM D 5813 : 2004 Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
ASTM D 5813 : 2004 : R2012 Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems

ASTM D 3859 : 2015 : REDLINE Standard Test Methods for Selenium in Water
ASTM D 543 : 2014 : REDLINE Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ASTM E 797 : 2005 Standard Practice for Measuring Thickness by Manual Ultrasonic Pulse-Echo Contact Method
ASTM F 1216 : 2016 : REDLINE Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
ASTM D 790 : 2017 : REDLINE Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ASTM D 3039/D3039M : 2017 : REDLINE Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials
ASTM D 1682 : 1964 TEST METHODS FOR BREAKING LOAD AND ELONGATION OF TEXTILE FABRICS
AWWA M28 : 2014 REHABILITATION OF WATER MAINS
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics

View more information
$122.77
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more