Customer Support: 131 242

i2i Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search

ASTM F 1901 : 2016 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems
Available format(s)

PDF

Superseded date

10-09-2022

Language(s)

English

Published date

30-08-2016

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 08.04, 2017 Specifies requirements for polyethylene (PE) pipe and fittings for nonpressure roof drain systems.

1.1This specification covers requirements for polyethylene (PE) pipe and fittings for nonpressure roof drain systems.

1.2This specification covers pipe and fittings intended for normal residential and commercial uses and is not intended for use in unusual corrosive conditions.

Note 1:Before installing pipe for waste disposal use, the approval of the cognizant building code authority shall be obtained as conditions not found in normal use or temperatures approaching 140°F (60°C) may be encountered.

1.3Pipe is produced in dimensions based on outside diameters of 32 mm (1.250 in.) and larger in accordance with Specification F714.

1.4The interchangeability of pipe and fittings made by different manufacturers is not addressed in this specification. Transition fittings for joining pipe and fittings of different manufacturers is provided for in this specification.

1.5Pipe and fittings are joined by the heat-fusion method, by the electrofusion method, or by using mechanical joints (excluding insert fittings) recommended by the manufacturer.

1.6In referee decisions, the SI units shall be used for metric-sized pipe and inch-pound units for pipe sized in the IPS system (ANSI B36.10). In all cases, the values given in parentheses are provided for information only.

1.7The following safety hazards caveat pertains only to the test method, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
F 17
DocumentType
Redline
Pages
7
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ICC IRC CODE AND COMMENTARY VOLUME 2 : 2015 IRC® Code and Commentary, Volume 2
ASTM F 2021 : 2017 : REDLINE Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems

MIL-STD-129 Revision R:2014 Military Marking for Shipment and Storage
ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
ASTM D 543 : 2014 : REDLINE Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ISO 161-1:1996 Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series
ASME B36.10 : 1979 WELDED AND SEAMLESS WROUGHT STEEL PIPE
ASTM D 3311 : 2017 : REDLINE Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns
ASTM F 477 : 2014 : REDLINE Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
ISO 161-2:1996 Thermoplastics pipes for the conveyance of fluids — Nominal outside diameters and nominal pressures — Part 2: Inch-based series
FED-STD-123 Revision H:2007 MARKING FOR SHIPMENT (CIVIL AGENCIES)
ASTM F 714 : 2013 : REDLINE Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter
ISO 3607:1977 Polyethylene (PE) pipes — Tolerances on outside diameters and wall thicknesses
ASTM D 2444 : 1999 Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
ASTM D 2122 : 2016 : REDLINE Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
ASTM D 3350 : 2014 : REDLINE Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 570 : 1998 : R2018 Standard Test Method for Water Absorption of Plastics

View more information
$122.77
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more