Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM F 2332 : 2006 : R2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Annular Ball Bearings for Instruments and Precision Rotating Components
Available format(s)

Hardcopy , PDF

Superseded date

23-08-2022

Language(s)

English

Published date

18-10-2013

CONTAINED IN VOL. 01.09, 2018 Provides annular ball bearings intended primarily for use in instrument and precision rotating components.

1.1This specification covers annular ball bearings intended primarily for use in instrument and precision rotating components. Instrument and precision ball bearings should meet tolerances specified in ABMA Standard 12.2, Instrument Ball Bearings Inch Design for Classes ABEC 5P and 7P.

1.2Intended Use—Ball bearings defined by this specification are intended for use in critical components of instrument systems. Such components range from air circulating blowers and drive motors through precision gear trains, gyro gimbals, and pickoffs to rate integrating spin-motors.

1.3The specification contains many of the requirements of MIL-B-81793, which was originally developed by the Department of Defense and maintained by the Naval Air Systems Command (Navy-AS) in Lakehurst, NJ. The following government activity codes may be found in the Department of Defense, Standardization Directory SD-1.2

Preparing activity

Custodians

Review activities

Navy - AS

Army - AT

Army-AV

Navy - AS

Navy - MC, SH

Air Force - 99

Air Force–84

DLA - GS


1.4Classification—Annular ball bearings for instrument and precision rotating components shall be of the following types, as specified:

1.4.1Type I—Annular ball bearing, for instruments and precision rotating components, deep groove, unflanged; (See Annex A1 – Annex A4)

1.4.2Type II—Annular ball bearing, for instruments and precision rotating components, deep groove, flanged; (See Annex A5 – Annex A8)

1.4.3Type III—Annular ball bearing, for instruments and precision rotating components, deep groove, unflanged, inner ring extended; (See Annex A9 – Annex A12)

1.4.4Type IV—Annular ball bearing, for instruments and precision rotating components, deep groove, flanged, inner ring extended; (See Annex A13 – Annex A16)

1.4.5Type V—Annular ball bearing, for instruments and precision rotating components, angular contact, unflanged, nonseparable, and counterbored outer ring; (See Annex A17 – Annex A20)

1.4.6Type VI—Annular ball bearing, for instruments and precision rotating components, angular contact, flanged, nonseparable, and counterbored outer ring on flange side; (See Annex A21 – Annex A24)

1.4.7Type VII—Annular ball bearing, for instruments and precision rotating components, angular contact, unflanged, separable, and stepped inner ring; (See Annex A25 – Annex A28)

1.4.8Type VIII—Annular ball bearing, for instruments and precision rotating components, angular contact, flanged, separable, and stepped inner ring; (See Annex A29 – Annex A32)

1.4.9Type IX—Annular ball bearing, for instruments and precision rotating components, angular contact, unflanged, nonseparable, and stepped inner ring. (See Annex A33 – Annex A36)

1.5Inch-Pound Specification—This specification covers only the inch-pound bearings.

1.5.1The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Committee
F 34
DocumentType
Standard
Pages
145
ProductNote
Reconfirmed 2013
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ISO 3290:2001 Rolling bearings Balls Dimensions and tolerances
ASTM D 2273 : 1997 : R2002 : EDT 1 Standard Test Method for Trace Sediment in Lubricating Oils
MIL-DTL-197 Revision M:2016 PACKAGING OF BEARINGS, ASSOCIATED PARTS AND SUBASSEMBLIES
MIL-STD-129 Revision R:2014 Military Marking for Shipment and Storage
MIL-STD-130 Revision N:2007 IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY
MIL-G-81937 Revision A:1984 GREASE, INSTRUMENT, ULTRA CLEAN, METRIC
ASTM A 240/A240M : 2011 Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
MIL-S-81087 Revision C:1981 SILICONE FLUID, CHLORINATED PHENYL METHYL POLYSILOXANE, NATO CODE NUMBER H-536
MIL-STD-1647 Revision E:2003 IDENTIFICATION MARKINGS FOR DOMESTICALLY MANUFACTURED BEARINGS, BALL, ANNULAR FOR INSTRUMENTS AND PRECISION COMPONENTS
ASTM D 2273 : 1997 : R2002 : EDT 2 Standard Test Method for Trace Sediment in Lubricating Oils
ASTM E 45 : 1997 : EDT 2 Standard Test Methods for Determining the Inclusion Content of Steel
ISO 14644-2:2015 Cleanrooms and associated controlled environments Part 2: Monitoring to provide evidence of cleanroom performance related to air cleanliness by particle concentration
ASTM D 2273 : 1997 Standard Test Method for Trace Sediment in Lubricating Oils
ASME B89.3.1 : 1972 MEASUREMENT OF OUT-OF-ROUNDNESS
ASTM A 666 : 2015 : REDLINE Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
ASTM A 240/A240M : 2005 Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
ABMA 10 : 1989 METAL BALLS
MIL-STD-206 Revision B:1988 FRICTION TORQUE TESTING FOR INSTRUMENT BALL BEARINGS PARTS 1 AND 2
ASME B46.1 : 2009 SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY)
MIL-PRF-83261 Revision C:2011 GREASE, AIRCRAFT, EXTREME PRESSURE, ANTI-WEAR
ASTM A 380 : 2006 Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems
ANSI/NCSL Z540 1 : 94(R2002) CALIBRATION - CALIBRATION LABORATORIES AND MEASURING AND TEST EQUIPMENT - GENERAL REQUIREMENTS
ASTM A 240/A240M : 2022 Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
SAE AMS QQ S 763D : 2013(S2015) STEEL, CORROSION RESISTANT, BARS, WIRE, SHAPES, AND FORGINGS
SAE AMS 5688 : 2012 STEEL, CORROSION-RESISTANT, WIRE, 18CR - 9.0NI (SAE 30302), SPRING TEMPER
SAE AMS 5880 : 2013 STEEL, CORROSION-RESISTANT, BARS, WIRE, AND FORGINGS, 17CR - 0.52MO (0.95 - 1.20C) (SAE 51440C), FOR BEARING APPLICATIONS
MIL-B-81744 Revision A:1973 BARRIER COATING SOLUTION, LUBRICANT MIGRATION DETERRING
ABMA 12.2 : 1992 INSTRUMENT BALL BEARINGS INCH DESIGN
SAE AMS 2303 : 2016 STEEL CLEANLINESS, AIRCRAFT QUALITY, MARTENSITIC CORROSION-RESISTANT STEELS, MAGNETIC PARTICLE INSPECTION PROCEDURE
ASTM A 756 : 2017 : R2022 Standard Specification for Stainless Anti-Friction Bearing Steel
ASTM D 2273 : 2008 Standard Test Method for Trace Sediment in Lubricating Oils
ASTM A 756 : 2017 : REDLINE Standard Specification for Stainless Anti-Friction Bearing Steel
MIL-STD-1334 Revision B:1977 PROCESS FOR BARRIER COATING OF ANTI-FRICTION BEARINGS
ISO 14644-1:2015 Cleanrooms and associated controlled environments Part 1: Classification of air cleanliness by particle concentration
MIL-PRF-6085 Revision E:2011 LUBRICATING OIL, INSTRUMENT, AIRCRAFT, LOW VOLATILITY
ASTM A 756 : 2017 Standard Specification for Stainless Anti-Friction Bearing Steel
ASTM A 240/A240M : 2020 : REV A Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
ASTM A 580/A580M : 2018 Standard Specification for Stainless Steel Wire
ASTM D 2273 : 2008 : R2012 Standard Test Method for Trace Sediment in Lubricating Oils
ASTM A 756 : 1994 Standard Specification for Stainless Anti-Friction Bearing Steel
ASTM D 2273 : 2005 Standard Test Method for Trace Sediment in Lubricating Oils
MIL-DTL-53131 Revision A:1998 LUBRICATING OIL, PRECISION ROLLING ELEMENT BEARING, POLYALPHAOLEFIN BASED
FED-STD-791 Revision D:2007 TESTING METHOD OF LUBRICANTS, LIQUID FUELS, AND RELATED PRODUCTS
ABMA 1 : 1990 TERMINOLOGY FOR ANTI-FRICTION BALL AND ROLLER BEARINGS AND PARTS
ISO 10012-1:1992 Quality assurance requirements for measuring equipment Part 1: Metrological confirmation system for measuring equipment
SAE AMS 6444 : 2015 STEEL, BARS, FORGINGS, AND TUBING, 1.45CR (0.93 - 1.05C) (SAE 52100), PREMIUM AIRCRAFT-QUALITY, CONSUMABLE ELECTRODE VACUUM REMELTED
ISO 1224:1984 Rolling bearings Instrument precision bearings
ASTM D 2273 : 2008 : R2016 Standard Test Method for Trace Sediment in Lubricating Oils (Withdrawn 2023)

View more information
$248.81
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more