Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM F 2879 : 2019

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Eye Protective Devices for Airsoft Sports
Available format(s)

Hardcopy , PDF

Superseded date

05-01-2022

Language(s)

English

Published date

16-04-2019

This specification applies to eye protective devices (EPDs) designed for use by participants in the sport of airsoft with 6-mm airsoft projectiles.

1.1This specification applies to eye protective devices (EPDs) designed for use by participants in the sport of airsoft with 6-mm airsoft projectiles. These EPDs are designed to minimize or significantly reduce injury to the eye and adnexa as a result of impact and penetration of airsoft projectiles.

1.2When airsoft guns are used for target practice with a paper or gel target and a backstop sufficient to prevent ricochet, shooters may wear eye protection (shooting glasses) appropriate for use with firearms, ball bullet (BB) guns or air guns that meet ANSI Z87.1. The balance of this specification applies to EPDs designed for use by participants in tactical sports using airsoft guns.

1.3EPDs meeting the requirements of this specification offer protection to the eyes and adnexa and not necessarily to any other parts of the head.

1.4This specification does not limit the wearing of eyeglasses or contact lenses when used in conjunction with the EPD based on the information provided by the manufacturer in 9.2.21.

1.5Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.

1.6The following information is provided for the laboratory conducting the test for the protection of their personnel: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 08
DocumentType
Standard
Pages
11
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM F 3398 : 2021 Standard Specification for Face and Ear Protective Devices for Air Soft Sports

ASTM F 2748 : 2019 Standard Specification for Airsoft Guns
ASTM F 2748 : 2008 Standard Specification for Low Energy Air Guns (Less Than 1 Joule)
ASTM D 1003 : 2007 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM F 2679 : 2007 Standard Specification for 6 mm Projectiles Used with Low Energy Air Guns
ASTM D 1003 : 2013 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM F 2679 : 2015 : R2019 Standard Specification for 6 mm Projectiles Used with Airsoft Guns
ASTM F 2748 : 2015 Standard Specification for Airsoft Guns
ASTM D 1003 : 2007 : EDT 1 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 1003 : 2011 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 1003 : 2021 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM F 2679 : 2015 : EDT 1 Standard Specification for 6 mm Projectiles Used with Airsoft Guns
ASTM D 1003 : 2000 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM F 2679 : 2015 Standard Specification for 6 mm Projectiles Used with Airsoft Guns
ASTM D 1003 : 2011 : EDT 1 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 1003 : 1992 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM F 2679 : 2013 Standard Specification for 6 mm Projectiles Used with Low Energy Air Guns
ASTM F 2748 : 2014 Standard Specification for Low Energy Air Guns
ASTM F 2748 : 2015 : R2019 Standard Specification for Airsoft Guns

View more information
$135.86
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more