Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM F 2881 : 2011 : R2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications
Available format(s)

Hardcopy , PDF

Superseded date

04-11-2015

Language(s)

English

Published date

01-08-2015

CONTAINED IN VOL. 08.04, 2018 Defines requirements and test methods for dual wall polypropylene pipe and fittings. The nominal inside diameters covered are 12 to 60 in. [300 to 1500 mm].

1.1This specification covers requirements and test methods for dual wall polypropylene pipe and fittings. The nominal inside diameters covered are 12 to 60 in. [300 to 1500 mm].

1.2The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure storm sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321.

1.3This specification covers pipe and fittings with an interior smooth wall and an annular corrugated profile outer wall (Fig. 1).

1.4Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.5The following precautionary statement caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
F 17
DocumentType
Standard
Pages
8
ProductNote
Reconfirmed 2015
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

MIL-STD-129 Revision R:2014 Military Marking for Shipment and Storage
ASTM D 618 : 2013 : REDLINE Standard Practice for Conditioning Plastics for Testing
ASTM A 666 : 2015 : REDLINE Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
ASTM D 1238 : 2013 : REDLINE Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
ASTM D 792 : 2013 : REDLINE Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
ASTM F 477 : 2014 : REDLINE Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
ASTM D 4389/D4389M : 2016 : REDLINE Standard Specification for Finished Glass Fabrics Woven From Rovings
ASTM D 3895 : 2014 Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
FED-STD-123 Revision H:2007 MARKING FOR SHIPMENT (CIVIL AGENCIES)
ASTM D 2444 : 1999 Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
ASTM D 790 : 2017 : REDLINE Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ASTM D 2122 : 2016 : REDLINE Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
AASHTO M 288 : 2015 SPECIFICATION FOR GEOSYNTHETIC SPECIFICATION FOR HIGHWAY APPLICATIONS
ASTM D 2990 : 2017 : REDLINE Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
ASTM D 6992 : 2016 : REDLINE Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics

View more information
$122.77
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more