Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM F 2994 : 2018

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Utilization of Mobile, Automated Cured-In-Place Pipe (CIPP) Impregnation Systems
Available format(s)

Hardcopy , PDF

Superseded date

18-10-2022

Language(s)

English

Published date

09-07-2018

1.1This practice describes the procedures for the impregnation of 2 to 48 in (50 to 1200 mm) diameter cured-in-place pipe utilizing mobile, automated systems. Temporary impregnation facilities set up at the jobsite (“over-the-hole” wet outs) are not covered under this standard. Once resin saturation is complete, the wet out liner is then used to rehabilitate existing gravity flow or pressure pipelines, process piping, electrical conduits or ventilation systems.

1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
F 17
DocumentType
Standard Practice
Pages
5
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 1600 : 1999 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM F 1216 : 2016 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
ASTM F 1216 : 2007 : REV B Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
ASTM D 5813 : 2004 : R2008 Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
ASTM F 412 : 2020 : REV A Standard Terminology Relating to Plastic Piping Systems
ASTM F 412 : 2021 Standard Terminology Relating to Plastic Piping Systems
ASTM F 1216 : 2009 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
ASTM F 1216 : 2008 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
ASTM D 1600 : 2007 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM F 1216 : 1998 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
ASTM D 1600 : 2013 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM F 1216 : 2006 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
ASTM D 1600 : 2014 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D 5813 : 2004 : R2018 Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
ASTM D 1600 : 2008 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM F 1216 : 2021 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
ASTM F 1216 : 2007 : REV A Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
ASTM D 5813 : 2004 Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
ASTM D 1600 : 2018 Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
ASTM F 1216 : 2005 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
ASTM F 1216 : 2007 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
ASTM D 5813 : 1995 Standard Specification for Cured-In-Place Thermosetting Resin Sewer Pipe
ASTM F 1216 : 2003 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
ASTM D 5813 : 2004 : R2012 Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
ASTM F 1216 : 2022 Standard Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube

View more information
$122.77
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more