Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM F 594 : 2009 : R2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Stainless Steel Nuts
Available format(s)

Hardcopy , PDF

Superseded date

07-08-2020

Language(s)

English

Published date

01-09-2015

CONTAINED IN VOL. 01.08, 2017 Describes the requirements for stainless steel nuts 0.25 to 1.50 in., inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.

1.1This specification covers the requirements for stainless steel nuts 0.25 to 1.50 in., inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.

1.2Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening.

Group

AlloysA

ConditionB

1

 304, 305, 304L
 384, 18–9LW, 302HQC

(CW)

  cold workedD

2

 316, 316L

(CW)

  cold workedD

3

 321, 347

(CW)

  cold workedD

4

 430E

(CW)

  cold workedD

5

 410F

(H)

  hardened and tempered

6

 431

(H)

  hardened and tempered

7

 630

(AH)

  aged hardened

(A)Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer (see 6.1).
(B)See 4.2 for options.
(C)When approved by the purchaser, alloys 303, 303Se, or XM1 may be furnished.
(D)Sizes 0.75 in. and larger may be hot worked and solution annealed.
(E)When approved by the purchaser, alloy 430F may be furnished.
(F)When approved by the purchaser, alloy 416 or 416Se may be furnished.

1.3Supplementary requirements of an optional nature are provided, applicable only when agreed upon by the manufacturer and the purchaser at the time of the inquiry and order.

1.4Suitable bolts, hex cap screws, and studs for use with nuts included in this specification are covered by Specification F593. Unless otherwise specified, all bolts, hex cap screws, and studs used with these nuts shall conform to the requirements of Specification F593 and shall be of the same alloy group.

1.5The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
F 16
DocumentType
Standard
Pages
8
ProductNote
Reconfirmed 2015
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM E 1470 : 1992 : R2006 Standard Test Method for Characterization of Proteins by Electrophoretic Mobility (Withdrawn 2014)
ASTM D 3951 : 2010 Standard Practice for Commercial Packaging
ASTM A 262 : 2015 : REDLINE Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
ASTM D 3951 : 1998 Standard Practice for Commercial Packaging
ASTM F 593 : 2017 : REDLINE Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
ASTM D 3951 : 2015 Standard Practice for Commercial Packaging
ASTM A 380 : 2006 Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems
ASTM D 3951 : 2018 Standard Practice for Commercial Packaging
ASTM E 1470 : 1992 : R1998 Standard Test Method for Characterization of Proteins by Electrophoretic Mobility
ASTM A 493 : 2016 : REDLINE Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging
ASME B18.2.2 : 2015 NUTS FOR GENERAL APPLICATIONS: MACHINE SCREW NUTS, HEX, SQUARE, HEX FLANGE, AND COUPLING NUTS (INCH SERIES)
ASTM A 342/A342M : 2014 : REDLINE Standard Test Methods for Permeability of Weakly Magnetic Materials
ASTM A 555/A555M : 2016 : REDLINE Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods

View more information
$122.77
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more