Customer Support: 131 242

i2i Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search
Home
ASTM
ASTM F 879 : 2015 : REDLINE

ASTM F 879 : 2015 : REDLINE

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Stainless Steel Socket Button and Flat Countersunk Head Cap Screws

Available format(s)

PDF

Superseded date

13-07-2023

Language(s)

English

Published date

01-05-2015

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 01.09, 2018 Specifies chemical and mechanical requirements for stainless steel inch hexagon socket button (SBHCS) and flat countersunk (SFHCS) head cap screws with nominal thread 0.060 through 0.625 in. intended for use in applications requiring general corrosion resistance.

1.1This specification covers the chemical and mechanical requirements for stainless steel inch hexagon socket button (SBHCS) and flat countersunk (SFHCS) head cap screws with nominal thread 0.060 through 0.625 in. intended for use in applications requiring general corrosion resistance.

1.2Two groups of austenitic stainless steel alloys and three conditions are covered. See Table 1 and Table 2.

(A)Actual full-size testing of condition CW and CW1 may result in decreased tensile strength because of the head configuration (see Table 3). For fasteners with nominal thread diameters larger than 0.625 in., the mechanical properties shall be agreed upon between the user and manufacturer.
(B)Core hardness is only required when full-size product testing cannot be accomplished.
(C)D denotes nominal thread size.
(A)304J3 from JIS G 4309.

1.3Units—The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

1.4The following precautionary caveat pertains only to the test method portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
F 16
DocumentType
Redline
Pages
9
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

SAE J 2295 : 2016 FASTENER PART STANDARD - CAP SCREWS, HEX, HEAVY HEX AND HEAVY HEX STRUCTURAL BOLTS, AND HEX NUTS (INCH DIMENSIONED)
ASME B18.3 : 2012 SOCKET CAP, SHOULDER, SET SCREWS, AND HEX KEYS (INCH SERIES)

ASTM A 262 : 2015 : REDLINE Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
ASTM F 606/F606M : 2016 : REDLINE Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
ASTM F 593 : 2017 : REDLINE Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
ASTM F 788 : 2013-04 SPECIFICATION FOR SURFACE DISCONTINUITIES OF BOLTS, SCREWS, AND STUDS, INCH AND METRIC SERIES
ASTM E 384 : 2017 : REDLINE Standard Test Method for Microindentation Hardness of Materials
ASME B18.3 : 2012 SOCKET CAP, SHOULDER, SET SCREWS, AND HEX KEYS (INCH SERIES)
ASTM A 967/A967M : 2017 : REDLINE Standard Specification for Chemical Passivation Treatments for Stainless Steel Parts
ASTM A 342/A342M : 2014 : REDLINE Standard Test Methods for Permeability of Weakly Magnetic Materials
ASTM A 555/A555M : 2016 : REDLINE Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods
ASTM A 380/A380M : 2017 Standard Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems
ASTM E 92 : 2017 : REDLINE Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials

View more information
$122.77
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more