Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM G 152 : 2013 : REDLINE

Current
Current

The latest, up-to-date edition.

Standard Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials
Available format(s)

PDF

Language(s)

English

Published date

01-07-2013

CONTAINED IN VOL. 14.04, 2015 Defines the basic principles and operating methods for using open flame carbon-arc light and water apparatus to reproduce the weathering effects, which occur when materials are exposed to sunlight through window glass or to direct sunlight and to moisture as rain or dew in actual use.

1.1This practice covers the basic principles and operating procedures for using open flame carbon-arc light and water apparatus intended to reproduce the weathering effects that occur when materials are exposed to sunlight (either direct or through window glass) and moisture as rain or dew in actual use. This practice is limited to the procedures for obtaining, measuring, and controlling conditions of exposure. A number of exposure procedures are listed in an appendix; however, this practice does not specify the exposure conditions best suited for the material to be tested.

Note 1Practice G151 describes performance criteria for all exposure devices that use laboratory light sources. This practice replaces Practice G23, which describes very specific designs for devices used for carbon-arc exposures. The apparatus described in Practice G23 is covered by this practice.

1.2Test specimens are exposed to filtered open flame carbon arc light under controlled environmental conditions. Different filters are described.

1.3Specimen preparation and evaluation of the results are covered in methods or specifications for specific materials. General guidance is given in Practice G151 and ISO 4892-1. More specific information about methods for determining the change in properties after exposure and reporting these results is described in Practice D5870.

1.4The values stated in SI units are to be regarded as the standard.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.5.1Should any ozone be generated from the operation of the light source, it shall be carried away from the test specimens and operating personnel by an exhaust system.

1.6This practice is technically similar to ISO 4892-4.

Committee
G 03
DevelopmentNote
Supersedes ASTM G 23 (12/2001)
DocumentType
Redline
Pages
16
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

ASTM G 141 : 2009 Standard Guide for Addressing Variability in Exposure Testing on Nonmetallic Materials
BS ISO 11617:2014 Buildings and civil engineering works. Sealants. Determination of changes in cohesion and appearance of elastic weatherproofing sealants after exposure of statically cured specimens to artificial weathering and mechanical cycling
CSA C22.2 No. 21 : 2014 CORD SETS AND POWER-SUPPLY CORDS
ASTM D 3451 : 2006 Standard Guide for Testing Coating Powders and Powder Coatings
ASTM D 3815/D3815M : 2005 : R2011 Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus
ASTM D 3451 : 2006 : R2017 Standard Guide for Testing Coating Powders and Powder Coatings
ASTM D 3089 : 1997 : R2008 Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes
ASTM D 6577 : 2015 : REDLINE Standard Guide for Testing Industrial Protective Coatings
ASTM C 1442 : 2014 : REDLINE Standard Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus
ASTM D 750 : 2012 Standard Practice for Rubber Deterioration Using Artificial Weathering Apparatus
ASTM D 3815/D3815M : 2005 : R2019 Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus
NACE RP 01 76 : 2003 CORROSION CONTROL OF STEEL FIXED OFFSHORE STRUCTURES ASSOCIATED WITH PETROLEUM PRODUCTION
16/30328596 DC : 0 BS ISO 9370 - PLASTICS - INSTRUMENTAL DETERMINATION OF RADIANT EXPOSURE IN WEATHERING TESTS - GENERAL GUIDANCE AND BASIC TEST METHOD
AASHTO M 181 :2010 SPECIFICATION FOR CHAIN-LINK FENCE
11/30229694 DC : 0 BS EN ISO 11997-2 - PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO CYCLIC CORROSION CONDITIONS - PART 2: WET (SALT FOG)/DRY/HUMIDITY/UV LIGHT
ISO 11617:2014 Buildings and civil engineering works Sealants Determination of changes in cohesion and appearance of elastic weatherproofing sealants after exposure of statically cured specimens to artificial weathering and mechanical cycling
07/30127278 DC : 0 BS ISO 9370 - PLASTICS - INSTRUMENTAL DETERMINATION OF RADIANT EXPOSURE IN WEATHERING TESTS - GENERAL GUIDANCE AND BASIC TEST METHOD
BS ISO 9370:2017 Plastics. Instrumental determination of radiant exposure in weathering tests. General guidance and basic test method
AWWA F101 : 2013 CONTACT-MOLDED, FIBERGLASS-REINFORCED PLASTIC WASH-WATER TROUGHS AND LAUNDERS
ASTM D 3815/D3815M : 2005 Standard Practice for Accelerated Weathering of Pressure-Sensitive Tapes by Open-Flame Carbon-Arc Exposure Apparatus
ASTM F 1665 : 2008 : R2013 Standard Specification for Poly(Vinyl Chloride) (PVC) and Other Conforming Organic Polymer-Coated Steel Barbed Wire Used With Chain-Link Fence
ASTM C 1530/C1530M : 2004 : R2010 : EDT 1 Standard Specification for Non-Asbestos Fiber-Cement Roofing Shakes, Shingles, and Slates with Designed Varying Profiles and Thicknesses
ASTM G 178 : 2016 : REDLINE Standard Practice for Determining the Activation Spectrum of a Material (Wavelength Sensitivity to an Exposure Source) Using the Sharp Cut-On Filter or Spectrographic Technique
ASTM F 1665 : 2008 : R2018 Standard Specification for Poly(Vinyl Chloride) (PVC) and Other Conforming Organic Polymer-Coated Steel Barbed Wire Used With Chain-Link Fence
ASTM F 1665 : 2008 Standard Specification for Poly(Vinyl Chloride) (PVC) and Other Conforming Organic Polymer-Coated Steel Barbed Wire Used With Chain-Link Fence
ASTM D 345 : 2002 Side bearings of the freight wagon bogies. General specifications
BS EN ISO 11997-2:2013 Paints and varnishes. Determination of resistance to cyclic corrosion conditions Wet (salt fog)/dry/humidity/UV light
ICC 2012 INTERNATIONAL BUILDING CODE : 2012 INTERNATIONAL BUILDING CODE
I.S. EN ISO 11997-2:2013 PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO CYCLIC CORROSION CONDITIONS - PART 2: WET (SALT FOG)/DRY/HUMIDITY/UV LIGHT (ISO 11997-2:2013)
ASTM F 1664 : 2008 : R2018 Standard Specification for Poly(Vinyl Chloride) (PVC) and Other Conforming Organic Polymer-Coated Steel Tension Wire Used with Chain-Link Fence
AASHTO M 181 : 2010 : R2015 SPECIFICATION FOR CHAIN-LINK FENCE
AWWA D121 : 2014 BOLTED ABOVEGROUND THERMOSETTING FIBERGLASS-REINFORCED PLASTIC PANEL-TYPE TANKS FOR WATER STORAGE
CSA C22.2 No. 18.3 : 2012 CONDUIT, TUBING, AND CABLE FITTINGS
C22.2 NO. 18.3-12 (R2017) Conduit, tubing, and cable fittings (Tri-national standard, with ANCE NMX-J-017 and UL 514B)
ASTM G 147 : 2017 : REDLINE Standard Practice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests
ASTM G 141 : 2009 : R2013 Standard Guide for Addressing Variability in Exposure Testing of Nonmetallic Materials
ICEA S 105-692 : 2011 600 VOLT SINGLE LAYER THERMOSET INSULATED UTILITY UNDERGROUND DISTRIBUTION CABLES
CSA C22.2 No. 211.2 : 2006 RIGID PVC (UNPLASTICIZED) CONDUIT
ASTM D 750 : 2012 : R2017 Standard Practice for Rubber Deterioration Using Artificial Weathering Apparatus
ASTM C 1530 : 2004 Standard Specification for Non-Asbestos Fiber-Cement Roofing Shakes, Shingles, and Slates with Designed Varying Profiles and Thicknesses
DIN EN ISO 11997-2:2013-12 PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO CYCLIC CORROSION CONDITIONS - PART 2: WET (SALT FOG)/DRY/HUMIDITY/UV LIGHT (ISO 11997-2:2013)
ICC IBC CODE AND COMMENTARY VOLUME 2 : 2015 IBC® Code and Commentary, Volume 2
UNI EN ISO 11997-2 : 2014 PAINTS AND VARNISHES - DETERMINATION OF RESISTANCE TO CYCLIC CORROSION CONDITIONS - PART 2: WET (SALT FOG)/DRY/HUMIDITY/UV LIGHT
13/30256722 DC : 0 BS ISO 11617 - BUILDINGS AND CIVIL ENGINEERING WORKS - SEALANTS - DETERMINATION OF CHANGES IN ADHESION, COHESION AND APPEARANCE OF ELASTIC WEATHERPROOFING SEALANTS AFTER EXPOSURE OF STATICALLY CURED SPECIMENS TO ARTIFICIAL WEATHERING AND MECHANICAL CYCLING
ASTM G 156 : 2017 : REDLINE Standard Practice for Selecting and Characterizing Weathering Reference Materials
MIL-PRF-18458 Revision C:2002 GREASE, WIRE ROPE - EXPOSED GEAR
ASTM D 3451 : 2006 : R2012 Standard Guide for Testing Coating Powders and Powder Coatings
ISO 4892-4:2013 Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps
ASTM E 2136 : 2004 : R2013 Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings—Durability (Withdrawn 2022)
UNE-EN ISO 11997-2:2014 Paints and varnishes - Determination of resistance to cyclic corrosion conditions - Part 2: Wet (salt fog)/dry/humidity/UV light (ISO 11997-2:2013)
ASTM E 2136 : 2004 Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings-Durability
ISO 11997-2:2013 Paints and varnishes — Determination of resistance to cyclic corrosion conditions — Part 2: Wet (salt fog)/dry/humidity/UV light
EN ISO 11997-2:2013 Paints and varnishes - Determination of resistance to cyclic corrosion conditions - Part 2: Wet (salt fog)/dry/humidity/UV light (ISO 11997-2:2013)
ISO 9370:2017 Plastics — Instrumental determination of radiant exposure in weathering tests — General guidance and basic test method
ASTM F 1664 : 2008 : R2013 Standard Specification for Poly(Vinyl Chloride) (PVC) and Other Conforming Organic Polymer-Coated Steel Tension Wire Used with Chain-Link Fence
CSA C22.2 No. 18.3 : 2012 : INC : UPD 1 : 2014 CONDUIT, TUBING, AND CABLE FITTINGS
ASTM F 668 : 2017 : REDLINE Standard Specification for Polyvinyl Chloride (PVC), Polyolefin and Other Polymer-Coated Steel Chain Link Fence Fabric
ASTM F 1664 : 2008 Standard Specification for Poly(Vinyl Chloride) (PVC) and Other Conforming Organic Polymer-Coated Steel Tension Wire Used with Chain-Link Fence
ASTM C 1530/C1530M : 2004(R2014) Standard Specification for Non-Asbestos Fiber-Cement Roofing Shakes, Shingles, and Slates with Designed Varying Profiles and Thicknesses
ASTM D 1499 : 2013 : REDLINE Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of Plastics
ASME A112.6.3 : 2016 FLOOR AND TRENCH DRAINS

ISO 4892-1:2016 Plastics Methods of exposure to laboratory light sources Part 1: General guidance
ASTM D 5870 : 2016 : REDLINE Standard Practice for Calculating Property Retention Index of Plastics
ISO 4892-4:2013 Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps
ASTM D 3980 : 1988 Practice for Interlaboratoy Testing of Paint and Related Materials (Withdrawn 1998)
ASTM G 113 : 2016 : REDLINE Standard Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials

View more information
$122.77
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more