ASTM G 63 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Guide for Evaluating Nonmetallic Materials for Oxygen Service
Hardcopy , PDF
17-03-2023
English
06-01-2016
This guide applies to nonmetallic materials, (hereinafter called materials) under consideration for oxygen or oxygen-enriched fluid service, direct or indirect, as defined below. It is intended for use in selecting materials for applications in connection with the production, storage, transportation, distribution, or use of oxygen.
1.1This guide applies to nonmetallic materials, (hereinafter called materials) under consideration for oxygen or oxygen-enriched fluid service, direct or indirect, as defined below. It is intended for use in selecting materials for applications in connection with the production, storage, transportation, distribution, or use of oxygen. It is concerned primarily with the properties of a material associated with its relative susceptibility to ignition and propagation of combustion; it does not involve mechanical properties, potential toxicity, outgassing, reactions between various materials in the system, functional reliability, or performance characteristics such as physical aging, degradation, abrasion, hardening, or embrittlement, except when these might contribute to an ignition.
1.2When this document was originally published in 1980, it addressed both metals and nonmetals. Its scope has been narrowed to address only nonmetals and a separate standard Guide G94 has been developed to address metals.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:The American Society for Testing and Materials takes no position respecting the validity of any evaluation methods asserted in connection with any item mentioned in this guide. Users of this guide are expressly advised that determination of the validity of any such evaluation methods and data and the risk of use of such evaluation methods and data are entirely their own responsibility.
Note 2:In evaluating materials, any mixture with oxygen exceeding atmospheric concentration at pressures higher than atmospheric should be evaluated from the hazard point of view for possible significant increase in material combustibility.
| Committee |
G 04
|
| DocumentType |
Guide
|
| Pages |
26
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM G 145 : 2008 : R2016 | Standard Guide for Studying Fire Incidents in Oxygen Systems |
| ASTM G 121 : 2018 | Standard Practice for Preparation of Contaminated Test Coupons for the Evaluation of Cleaning Agents |
| ASTM F 1792 : 1997 : R2021 | Standard Specification for Special Requirements for Valves Used in Gaseous Oxygen Service |
| ASTM G 175 : 2013 : R2021 | Standard Test Method for Evaluating the Ignition Sensitivity and Fault Tolerance of Oxygen Pressure Regulators Used for Medical and Emergency Applications |
| ASTM G 114 : 2021 | Standard Practices for Evaluating the Age Resistance of Polymeric Materials Used in Oxygen Service |
| ASTM G 124 : 2018 | Standard Test Method for Determining the Combustion Behavior of Metallic Materials in Oxygen-Enriched Atmospheres |
| ASTM G 126 : 2016 | Standard Terminology Relating to the Compatibility and Sensitivity of Materials in Oxygen Enriched Atmospheres |
| ASTM G 74 : 2013 : R2021 | Standard Test Method for Ignition Sensitivity of Nonmetallic Materials and Components by Gaseous Fluid Impact |
| ASTM G 94 : 2005 : R2014 | Standard Guide for Evaluating Metals for Oxygen Service |
| ASTM G 88 : 2013 : EDT 1 | Standard Guide for Designing Systems for Oxygen Service |
| ASTM D 1748 : 2022 | Standard Test Method for Rust Protection by Metal Preservatives in the Humidity Cabinet |
| ASTM D 217 : 2021 | Standard Test Methods for Cone Penetration of Lubricating Grease |
| ASTM D 4809 : 2000 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM D 2512 : 1995 | Standard Test Method for Compatibility of Materials with Liquid Oxygen (Impact Sensitivity Threshold and Pass-Fail Techniques) |
| ASTM G 94 : 2022 | Standard Guide for Evaluating Metals for Oxygen Service |
| ASTM D 4809 : 2018 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM D 1264 : 2016 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 4809 : 2013 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM D 1743 : 2005 : REV A | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 2863 : 2008 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 217 : 2021 : REV A | Standard Test Methods for Cone Penetration of Lubricating Grease |
| ASTM D 4809 : 2009 : REV A : EDT 1 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM G 88 : 2013 | Standard Guide for Designing Systems for Oxygen Service |
| ASTM D 4809 : 2000 : R2005 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM D 1264 : 2003 : EDT 1 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 1264 : 2011 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM G 88 : 2021 | Standard Guide for Designing Systems for Oxygen Service |
| ASTM D 2863 : 2012 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 2863 : 2000 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 1748 : 2002 | Standard Test Method for Rust Protection by Metal Preservatives in the Humidity Cabinet |
| ASTM D 1748 : 2002 : R2008 | Standard Test Method for Rust Protection by Metal Preservatives in the Humidity Cabinet |
| ASTM D 217 : 2019 : REV B | Standard Test Methods for Cone Penetration of Lubricating Grease |
| ASTM D 4809 : 1995 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM D 2863 : 2006 : REV A | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 2863 : 2009 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 1748 : 2010 : R2015 | Standard Test Method for Rust Protection by Metal Preservatives in the Humidity Cabinet |
| ASTM D 1264 : 2000 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 1743 : 2005 | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM G 74 : 2013 | Standard Test Method for Ignition Sensitivity of Nonmetallic Materials and Components by Gaseous Fluid Impact |
| ASTM D 2512 : 1995 : R2002 | Standard Test Method for Compatibility of Materials with Liquid Oxygen (Impact Sensitivity Threshold and Pass-Fail Techniques) |
| ASTM D 4809 : 2009 : REV A | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM D 1264 : 2012 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 2863 : 1995 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-like Combustion of Plastics (Oxygen Index) |
| ASTM D 1743 : 2021 | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 2863 : 2019 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 217 : 1997 | Standard Test Methods for Cone Penetration of Lubricating Grease |
| ASTM D 1743 : 2022 | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 2863 : 2006 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 1743 : 2010 | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 1264 : 2018 : EDT 1 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 1264 : 2003 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 1264 : 2003 : R2008 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 4809 : 2009 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM D 2512 : 1995 : R2002 : EDT 1 | Standard Test Method for Compatibility of Materials with Liquid Oxygen (Impact Sensitivity Threshold and Pass-Fail Techniques) |
| ASTM D 1748 : 1983 : R1993 : EDT 1 | Standard Test Method for Rust Protection by Metal Preservatives in the Humidity Cabinet |
| ASTM D 4809 : 2006 | Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) |
| ASTM D 2512 : 2017 | Standard Test Method for Compatibility of Materials with Liquid Oxygen (Impact Sensitivity Threshold and Pass-Fail Techniques) (Withdrawn 2023) |
| ASTM D 1743 : 2013 | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 2863 : 2017 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 2512 : 1995 : R2008 | Standard Test Method for Compatibility of Materials with Liquid Oxygen (Impact Sensitivity Threshold and Pass-Fail Techniques) (Withdrawn 2017) |
| ASTM D 1743 : 2001 | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 1748 : 2010 | Standard Test Method for Rust Protection by Metal Preservatives in the Humidity Cabinet |
| ASTM D 1743 : 2005 : REV A : EDT 1 | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 1264 : 1996 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 2863 : 2017 : REV A | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 1743 : 1994 : EDT 1 | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 1743 : 2013 : R2018 | Standard Test Method for Determining Corrosion Preventive Properties of Lubricating Greases |
| ASTM D 1748 : 2000 | Standard Test Method for Rust Protection by Metal Preservatives in the Humidity Cabinet |
| ASTM G 86 : 2017 | Standard Test Method for Determining Ignition Sensitivity of Materials to Mechanical Impact in Ambient Liquid Oxygen and Pressurized Liquid and Gaseous Oxygen Environments |
| ASTM D 1264 : 2018 | Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greases |
| ASTM D 2863 : 2010 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 2863 : 2012 : EDT 1 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
| ASTM D 2863 : 2013 | Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.