Skip to content
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site X
Please enter a keyword to search

  • AWWA C606 : 2015

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    View superseded by
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    GROOVED AND SHOULDERED JOINTS

    Available format(s):  Hardcopy, PDF

    Superseded date:  07-04-2023

    Language(s):  English

    Published date:  01-06-2015

    Publisher:  American Water Works Association

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    I Introduction
    II Special ISSUES
    III Use of This Standard
    IV Major Revisions
    V Comments
    Standard
    1 General
    2 References
    3 Definitions
    4 Requirements
    5 Verification
    6 Delivery
    Appendix
    A - Guidelines for Grooved and
         Shouldered Piping Spacing,
         Support, Anchorage, and
         Guidance

    Abstract - (Show below) - (Hide below)

    Specifies grooved and shouldered joints for ductile-iron pipe, metallic pressure pipe of iron pipe size (IPS), fittings, and other components for water service. The standard describes 4-in. through 36-in. (100-mm through 900-mm) diameter grooved ductile-iron pipe; ?-in. through 24-in. (19-mm through 600-mm) diameter grooved steel, aluminum, brass, and other metallic pipe of IPS dimensions; and 4-in. through 64-in. (100-mm through 1,600-mm) nominal diameter shouldered ends for ductile-iron pipe and metallic pipe of IPS dimensions.

    General Product Information - (Show below) - (Hide below)

    Document Type Revision
    Publisher American Water Works Association
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    FM 1020 : 2007 AUTOMATIC WATER CONTROL VALVES
    FM 1610 : 2016 DUCTILE IRON PIPE AND FITTINGS, FLEXIBLE FITTINGS AND COUPLINGS
    AWWA C226 : 2013 STAINLESS-STEEL FITTINGS FOR WATERWORKS SERVICE, SIZES 1/2 IN. THROUGH 72 IN. (13 MM THROUGH 1,800 MM)
    ASTM A 377 : 2003 Standard Index of Specifications for Ductile-Iron Pressure Pipe
    MSS SP 145 : 2013 METAL BALL VALVES FOR LOW PRESSURE/LOW TEMPERATURE PLUMBING APPLICATIONS
    ASME A112.4.14-2017/CSA B125.14-17 Manually operated valves for use in plumbing systems
    ASTM A 377 : 2003 : R2008 : EDT 1 Standard Index of Specifications for Ductile-Iron Pressure Pipe
    NFPA 13 HDBK : 2016 AUTOMATIC SPRINKLER SYSTEMS HANDBOOK
    NFPA 20 HDBK : 2016 STATIONARY FIRE PUMPS HANDBOOK
    FM 1421 : 2007 MONITOR ASSEMBLY
    ASTM F 1476 : 2007 Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications
    MIL-PRF-13789 Revision E:1999 STRAINERS, SEDIMENT: PIPELINE, BASKET TYPE
    FM 1112 : 2006 INDICATING VALVES (BUTTERFLY OR BALL TYPE)
    AWWA C518 : 2013 DUAL-DISC SWING-CHECK VALVES FOR WATERWORKS SERVICE
    AWWA C604:2017 INSTALLATION OF BURIED STEEL WATER PIPE - 4 IN. (100 MM) AND LARGER
    FM 1230 : 2013 ANTI-WATER HAMMER CHECK VALVES
    ASTM F 1548 : 2001 Standard Specification for the Performance of Fittings for Use with Gasketed Mechanical Couplings Used in Piping Applications
    ASTM F 1548 : 2001 : R2012 Standard Specification for Performance of Fittings for Use with Gasketed Mechanical Couplings Used in Piping Applications
    ASME B31.1 : 2016 POWER PIPING
    ASME A112.4.14 : 2017 MANUALLY OPERATED QUARTER-TURN SHUTOFF VALVES FOR USE IN PLUMBING SYSTEMS
    ASME B31.3:2016 PROCESS PIPING
    FM 1035 : 2014 NITROGEN GENERATORS
    FM 1056 : 2010 SIGHT DRAINS FOR AUTOMATIC SPRINKLER SYSTEMS
    AWWA C220 : 2017 STAINLESS-STEEL PIPE, 1/2 IN. (13 MM) AND LARGER
    AWWA C520 : 2014 KNIFE GATE VALVES, SIZES 2 IN. (50 MM) THROUGH 96 IN. (2,400 MM)
    FM 1530 : 2016 FIRE DEPARTMENT CONNECTIONS
    ASTM F 1548 : 2001 : R2006 Standard Specification for the Performance of Fittings for Use with Gasketed Mechanical Couplings Used in Piping Applications
    FM 5551 : 1963 STRAINERS FOR USE WITH WATER BASED FIRE PROTECTION SYSTEMS
    FM 1043 : 2011 WATER FLOW DETECTOR TESTERS 1 INCH THROUGH 8 INCH NOMINAL SIZE
    AWWA M41 : 3 DUCTILE-IRON PIPE AND FITTINGS
    MIL PRF 370 : K HOSE AND HOSE ASSEMBLIES, NONMETALLIC: ELASTOMERIC, LIQUID FUEL
    ASTM F 1476 : 2007 : R2013 Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications
    AWWA C517 : 2016 RESILIENT-SEATED CAST-IRON ECCENTRIC PLUG VALVES
    ASTM A 377 : 2003 : R2014 Standard Index of Specifications for Ductile-Iron Pressure Pipe
    MSS SP 139 : 2014 COPPER ALLOY GATE, GLOBE, ANGLE, AND CHECK VALVES FOR LOW PRESSURE/LOW TEMPERATURE PLUMBING APPLICATIONS
    MSS SP 67 : 2017 BUTTERFLY VALVES
    FM 1034 : 2013 AIR DRYING UNITS
    AWWA C150/A21.50 : 2014 THICKNESS DESIGN OF DUCTILE-IRON PIPE
    FM 1631 : 2006 ADJUSTABLE AND FIXED SPRINKLER FITTINGS 1/2 INCH THROUGH 1 INCH NOMINAL SIZE
    FM 1364 : 2013 EXPANSION CHAMBERS
    FM 1041 : 2006 ALARM CHECK VALVES

    Standards Referencing This Book - (Show below) - (Hide below)

    NSF 61 : 2016 DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS
    AWWA C151/A21.51 : 2017 DUCTILE-IRON PIPE, CENTRIFUGALLY CAST
    ASTM A 183 : 2014 : REDLINE Standard Specification for Carbon Steel Track Bolts and Nuts
    NFPA 13 : 2016 INSTALLATION OF SPRINKLER SYSTEMS
    ASTM A 449 : 2014 : REDLINE Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective
Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more