We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS 3602-2:1991

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    STEEL PIPES AND TUBES FOR PRESSURE PURPOSES: CARBON AND CARBON MANGANESE STEEL WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES - SPECIFICATION FOR LONGITUDINALLY ARC WELDED TUBES

    Available format(s):  Hardcopy, PDF

    Superseded date:  26-06-2002

    Language(s):  English

    Published date:  01-01-1991

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Committees responsible
    Foreword
    Specification
    1 Scope
    2 Information to be supplied by the purchaser and
        options to be documented
    3 Designation
    4 Manufacture of the steel
    5 Manufacture of the product
    6 Chemical analysis
    7 Final supply condition
    8 Mechanical properties
    9 Visual inspection and appearance
    10 Tolerances
    11 Tests
    12 Number, selection and preparation of samples and
        test pieces
    13 Test methods
    14 Retests
    15 Test certificate
    16 Protective coating
    17 Marking
    Appendices
    A Designations of steel tubes in BS 3602 : Part 2 :
        1991 and the nearest equivalent designations in
        BS 3602 : Part 2 : 1978 and ISO 2604 : Part VI
    B Dimensional limits of tubes
    C Ultrasonic testing of the weld for the detection of
        longitudinal and transverse imperfections
    D Radiographic acceptance limits
    E Procedure for the verification of elevated
        temperature proof stress values

    Abstract - (Show below) - (Hide below)

    Specifies requirements for longitudinally arc welded, plain end, carbon manganese and carbon tubes for pressure purposes. Tubes manufactured in accordance with this standard have specified room temperature properties and specified proof stress values at elevated temperatures. Covers Information to be supplied by the purchaser (which will be fully documented): the designation of the tubes, the type of steel, the number and part of the British Standard and the final supply condition; the tube length, if exact; the tube outside diameter and thickness and the number of lengths or quantity in metres. Also, includes detailed coverage of Options to be documented.

    General Product Information - (Show below) - (Hide below)

    Committee ISM/73
    Development Note SUPERSEDES BS 3602: PART 2: 1978
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    EN 10002-1 : 2001 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE
    BS 1501-1(1980) : 1980 STEELS FOR PRESSURE PURPOSES - PART 1: SPECIFICATION FOR CARBON AND CARBON MANGANESE STEELS: PLATES
    BS 3894-1(1965) : 1965 METHOD FOR CONVERTING ELONGATION VALUES FOR STEEL - CARBON AND LOW ALLOY STEELS
    BS 3605-1(1991) : 1991 AUSTENITIC STAINLESS STEEL PIPES AND TUBES FOR PRESSURE PURPOSES - SPECIFICATION FOR SEAMLESS TUBES
    BS 2600-1(1983) : 1983 RADIOGRAPHIC EXAMINATION OF FUSION WELDED BUTT JOINTS IN STEEL - METHODS FOR STEEL 2 MM UP TO AND INCLUDING 50 MM THICK
    BS 3688-1(1963) : 1963 METHODS FOR MECHANICAL TESTING OF METALS AT ELEVATED TEMPERATURES - PART 1: TENSILE TESTING
    BS 3602-1(1987) : 1987 STEEL PIPES AND TUBES FOR PRESSURE PURPOSES: CARBON AND CARBON MANGANESE STEEL WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES - SPECIFICATION FOR SEAMLESS AND ELECTRIC RESISTANCE WELDED INCLUDING WELDED TUBES
    EN 10045-1 : 1990 METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD
    BS 3889-1(1983) : 1983 METHODS FOR NON-DESTRUCTIVE TESTING OF PIPES AND TUBES - METHODS OF AUTOMATIC ULTRASONIC TESTING FOR THE DETECTION OF IMPERFECTIONS IN WROUGHT STEEL TUBES
    BS 4871-1(1982) : 1982 SPECIFICATION FOR APPROVAL TESTING OF WELDERS WORKING TO APPROVED WELDING PROCEDURES - FUSION WELDING OF STEEL
    BS 3604-1(1990) : 1990 STEEL PIPES AND TUBES FOR PRESSURE PURPOSES: FERRITIC ALLOY STEEL WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES - SPECIFICATION FOR SEAMLESS AND ELECTRIC RESISTANCE WELDED TUBES
    BS 4870-1(1981) : 1981 SPECIFICATION FOR APPROVAL TESTING OF WELDING PROCEDURES - FUSION WELDING OF STEEL
    BS 4870-4(1988) : 1988 APPROVAL TESTING OF WELDING PROCEDURES - SPECIFICATION FOR AUTOMATIC FUSION WELDING OF METALLIC MATERIALS, INCLUDING WELDING OPERATOR APPROVAL
    BS 499-1(1991) : 1991 WELDING TERMS AND SYMBOLS - GLOSSARY FOR WELDING, BRAZING AND THERMAL CUTTING
    ISO 2604-6:1978 Steel products for pressure purposes Quality requirements Part 6: Submerged arc longitudinally or spirally welded steel tubes
    ASME B36.10M : 2015 WELDED AND SEAMLESS WROUGHT STEEL PIPE
    BS 2901-1(1983) : 1983 FILLER RODS AND WIRES FOR GAS-SHIELDED ARC WELDING - FERRITIC STEELS
    BS 5750-2(1987) : 1987 QUALITY SYSTEMS - SPECIFICATION FOR PRODUCTION AND INSTALLATION
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective