Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS 3757:1978

Current
Current

The latest, up-to-date edition.

Specification for rigid PVC sheet
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

29-12-1978

Foreword
Cooperating organizations
Specification
1 Scope
2 References
3 Definition
4 General requirements
5 Performance requirements
Appendices
A Determination of resistance to delamination
B Determination of retention of embossed surface after
   heating
C Determination of retention of embossed surface after
   heating of sheet to be used for vacuum forming
D Determination of impact strength
E Determination of tensile strength
F Determination of dimensional change at 120 degree C

Requirements for rigid PVC sheet of nominal thickness 0.25 mm and above, classified into 6 types according to method of manufacture and intended use.

This British Standard specifies requirements for rigid PVC sheet of nominal thickness 0.25 mm and above. Rigid PVC sheet is classified into six types as shown in table 1, and is available in a wide range of colours. Types A and B are manufactured by press lamination or press surfacing and types C and D by calendering or extrusion.

Table 1. Type descriptions

Type Description (see note)
A1 C1 General purpose sheet suitable for most applications and fabricating techniques.
A3 C3 Sheet similar to types A1 and C1 but with specific impact strength. The chemical resistance of these types may be inferior to that of types A1 and C1.
B D Sheet particularly suitable for deep vacuum forming. These types are generally characterized by a lower softening point and the maximum service temperature of articles made from them may consequently be reduced.

NOTE. The descriptions of the various types in table 1 are given for general guidance, but the suitability of the material for a particular application depends on several factors and the supplier’s advice should always be sought before a final choice is made, particularly where the application involves contact with chemicals. The suitability of the product for any chemical application should be assessed on background knowledge and service conditions required, and, if necessary, tests relevant to the specific applications should be carried out. Where the sheet is to be used in contact with foodstuffs or potable water, discussion with the supplier is essential since selected formulations are normally required in such cases. Intending users of rigid PVC sheet for foodstuffs contact applications are advised to consult the ‘Code of practice for plastics in foodstuffs contact applications’ published by the British Plastics Federation, 5 Belgrave Square, London SW1 × 8PH, with the cooperation of the British Industrial Biological Research Association.

Committee
PRI/75
DevelopmentNote
Reviewed and confirmed by BSI, December 2011. (11/2011)
DocumentType
Standard
Pages
10
PublisherName
British Standards Institution
Status
Current
Supersedes

BS 5350-A2:1990 Methods of test for adhesives. Adherends Guide to the selection of adherend materials
BS 1133-21:1991 Packaging code Regenerated cellulose film, films made of plastics, aluminium foil, flexible multilayer structures and metallized materials
BS 5350-C5:2002 Methods of test for adhesives Determination of bond strength in longitudinal shear for rigid adherends
BS 7258-1:1994 Laboratory fume cupboards Specification for safety and performance
BS 6464:1984 Specification for reinforced plastics pipes, fittings and joints for process plants
BS 7159:1989 Code of practice for design and construction of glass-reinforced plastics (GRP) piping systems for individual plants or sites

BS 2782-3:Methods 320A to 320F:1976 Methods of testing plastics. Mechanical properties Tensile strength, elongation and elastic modulus
BS 2782-1.120A,B,D,E(1990) : LATEST METHODS OF TESTING PLASTICS - THERMAL PROPERTIES - METHODS 120A, B, D AND E - DETERMINATION OF VICAT SOFTENING TEMPERATURE OF THERMOPLASTICS

View more information
$247.06
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more