BS 4551(2005) : 2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
MORTAR - METHODS OF TEST FOR MORTAR AND SCREED - CHEMICAL ANALYSIS AND PHYSICAL TESTING
Hardcopy , PDF
22-06-2014
English
01-01-2005
Committees responsible
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and designations
5 Sampling
6 Physical tests
7 Chemical analysis
8 Reports for chemical analysis
9 Calculation of mix proportions and interpretation
of results
Annex A (informative) - Information relevant to the
calculations of mix proportions of hardened
mortars, screeds and plasters
Annex B (informative) - Estimates of precision in the
analysis of hardened mortars/screeds
Bibliography
Defines methods for sampling, preparation, physical testing and chemical analysis of mortars for bricklaying, screeding, plastering and rendering.
Committee |
B/519/2
|
DevelopmentNote |
Supersedes BS 4551-2(1998) and 05/30125494 DC. Together with BS EN 1015-1, BS EN 1015-2, BS EN 1015-3, BS EN 1015-4, BS EN 1015-6, BS EN 1015-7, BS EN 1015-9, BS EN 1015-10, BS EN 1015-11 and BS EN 1015-19 supersedes BS 4551-1(1998). (09/2005) Supersedes 09/30167521 DC. (01/2010) 2005 Edition Re-Issued in May 2013 & incorporates AMD 2 2013. Supersedes 12/30274515 DC. (05/2013)
|
DocumentType |
Standard
|
Pages |
42
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
BS 1191-2:1973 | Specification for gypsum building plasters Premixed lightweight plasters |
BS 5385-2:2006 | Wall and floor tiling Design and installation of external ceramic and mosaic wall tiling in normal conditions. Code of practice |
BS 5385-2:2015 | Wall and floor tiling Design and installation of external ceramic, natural stone and mosaic wall tiling in normal conditions. Code of practice |
BS 5080-2:1986 | Structural fixings in concrete and masonry Method for determination of resistance to loading in shear |
BS 1881-124:1988 | Testing concrete Methods for analysis of hardened concrete |
BS 8204-1(2003) : 2003 | SCREEDS, BASES AND IN SITU FLOORINGS - PART 1: CONCRETE BASES AND CEMENTITIOUS LEVELLING SCREEDS TO RECEIVE FLOORINGS - CODE OF PRACTICE |
BS 1191-1:1973 | Specification for gypsum building plasters Excluding premixed lightweight plasters |
PD 6678:2005 | Guide to the specification of masonry mortar |
BS 5385-1:2009 | Wall and floor tiling Design and installation of ceramic, natural stone and mosaic wall tiling in normal internal conditions. Code of practice |
BS 5385-3:2007 | Wall and floor tiling Design and installation of internal and external ceramic and mosaic floor tiling in normal conditions. Code of practice |
BS 5385-3:2014 | Wall and floor tiling Design and installation of internal and external ceramic and mosaic floor tiling in normal conditions. Code of practice |
BS EN 1015-11:1999 | Methods of test for mortar for masonry Determination of flexural and compressive strength of hardened mortar |
BS 5404-1:1976 | Specification for plastics laboratory ware Beakers |
BS 6463-103:1999 | Quicklime, hydrated lime and natural calcium carbonate Methods for physical testing |
BS 6463-102:2001 | Quicklime, hydrated lime and natural calcium carbonate Methods for chemical analysis |
ISO 3310-1:2016 | Test sieves Technical requirements and testing Part 1: Test sieves of metal wire cloth |
BS EN 933-1:2012 | Tests for geometrical properties of aggregates Determination of particle size distribution. Sieving method |
BS EN ISO 3696:1995 | Water for analytical laboratory use. Specification and test methods |
BS EN 1015-4:1999 | Methods of test for mortar for masonry Determination of consistence of fresh mortar (by plunger penetration) |
BS EN 413-1:2011 | Masonry cement Composition, specifications and conformity criteria |
BS EN 1015-3:1999 | Methods of test for mortar for masonry Determination of consistence of fresh mortar (by flow table) |
BS EN 1015-17:2000 | Methods of test for mortar for masonry Determination of water-soluble chloride content of fresh mortars |
BS EN 1015-2:1999 | Methods of test for mortar for masonry Bulk sampling of mortars and preparation of test mortars |
BS EN 1015-9:1999 | Methods of test for mortar for masonry Determination of workable life and correction time of fresh mortar |
BS EN 197-4:2004 | Cement Composition, specifications and conformity criteria for low early strength blastfurnace cements |
BS ISO 5725-2:1994 | Accuracy (trueness and precision) of measurement methods and results Basic methods for the determination of repeatability and reproducibility of a standard measurement method |
BS EN 1015-7:1999 | Methods of test for mortar for masonry Determination of air content of fresh mortar |
BS 410-1:2000 | Test sieves. Technical requirements and testing Test sieves of metal wire cloth |
BS EN 459-1:2015 | Building lime Definitions, specifications and conformity criteria |
BS EN 1015-1:1999 | Methods of test for mortar for masonry Determination of particle size distribution (by sieve analysis) |
BS 700-1:1982 | Graduated pipettes Specification for general requirements |
BS EN 998-1:2016 | Specification for mortar for masonry Rendering and plastering mortar |
BS EN 459-2:2010 | Building lime Test methods |
BS EN 1015-21:2002 | Methods of test for mortar for masonry Determination of the compatibility of one-coat rendering mortars with substrates |
BS EN 197-1:2011 | Cement Composition, specifications and conformity criteria for common cements |
BS EN 933-2:1996 | Tests for geometrical properties of aggregates Determination of particle size distribution. Test sieves, nominal size of apertures |
BS EN 459-3:2015 | Building lime Conformity evaluation |
BS EN 1015-12:2016 | Methods of test for mortar for masonry Determination of adhesive strength of hardened rendering and plastering mortars on substrates |
BS 700-2:1982 | Graduated pipettes Specification for pipettes for which no waiting time is specified |
BS 6463-101:1996 | Quicklime, hydrated lime and natural calcium carbonate Methods for preparing samples for testing |
BS EN 1015-6:1999 | Methods of test for mortar for masonry Determination of bulk density of fresh mortar |
BS EN 1015-10:1999 | Methods of test for mortar for masonry Determination of dry bulk density of hardened mortar |
BS 1881-124:1988 | Testing concrete Methods for analysis of hardened concrete |
BS 700-3:1982 | Graduated pipettes Specification for blow-out pipettes |
BS 812-120:1989 | Testing aggregates Method for testing and classifying drying shrinkage of aggregates in concrete |
BS EN 197-2:2014 | Cement Conformity evaluation |
BS EN 1015-19:1999 | Methods of test for mortar for masonry Determination of water vapour permeability of hardened rendering and plastering mortars |
BS EN 1015-18:2002 | Methods of test for mortar for masonry Determination of water absorption coefficient due to capillary action of hardened mortar |
BS 4027:1996 | Specification for sulfate-resisting Portland cement |
BS 6100-9:2007 | Building and civil engineering. Vocabulary Work with concrete and plaster |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.