We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS 5T100(2010) : 2010

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    AEROSPACE SERIES - PROCEDURE FOR INSPECTION, TESTING AND ACCEPTANCE OF SEAMLESS STEEL TUBES AND TUBESTOCK

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2010

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Section 1 - General requirements
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 General
    5 Information and requirements to be agreed and to be
       documented
    6 Tubestock manufacture, inspection and testing
    7 Tube manufacture, inspection and testing
    8 Testing
    9 Defects
    10 Maintenance of identity
    11 Final marking
    12 Protection and packaging
    13 Certification
    Section 2 - Tubes delivered in the final heat-treated
                condition (excluding austenitic steels)
    14 General
    15 Mechanical tests
    16 Hardness test
    17 Decarburization test
    18 Non-destructive tests
    Section 3 - Corrosion-resisting and heat-resisting
                austenitic steel tubes (elevated temperature
                properties not verified)
    19 General
    20 Mechanical tests
    21 Hardness test
    22 Surface finish
    23 Freedom from surface contamination
    24 Susceptibility to intercrystalline corrosion
    25 Non-destructive tests
    Section 4 - Tubes delivered in the softened condition
                for use in the hardened and tempered condition
    26 General
    27 Selection of mechanical test samples
    28 Mechanical tests
    29 Decarburization test
    30 Non-destructive tests
    Section 5 - Modified requirements for the
                acceptance of small quantities of
                tubes and tubestock
    31 General
    32 General requirements
    33 Micro-cleanness assessment
    34 Other tests
    Annexes
    Annex A (normative) - Rules for application of
            values for mechanical properties given in
            material specifications
    Annex B (normative) - Dimensions and tolerances
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes procedures for the inspection, testing and acceptance of seamless steel tube and tubestock for aerospace use.

    General Product Information - (Show below) - (Hide below)

    Committee ACE/61/-/15
    Development Note Supersedes BS 4T100(1997) & 09/30199781 DC. (12/2013)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    BS EN 2002-2 : 2005 AEROSPACE SERIES - METALLIC MATERIALS - TEST METHODS - PART 2: TENSILE TESTING AT ELEVATED TEMPERATURE
    BS EN ISO 6506-1:2014 Metallic materials. Brinell hardness test Test method
    BS EN ISO 6508-1:2015 METALLIC MATERIALS - ROCKWELL HARDNESS TEST - PART 1: TEST METHOD (ISO 6508-1:2016)
    BS 1639(1964) : 1964 METHODS FOR BEND TESTING OF METALS
    BS EN ISO 6507-1:2005 METALLIC MATERIALS - VICKERS HARDNESS TEST - PART 1: TEST METHOD
    BS EN ISO 7438:2016 METALLIC MATERIALS - BEND TEST
    BS EN ISO 8493 : 2004 METALLIC MATERIALS - TUBE - DRIFT-EXPANDING TEST
    BS 6S100(2010) : 2010 AEROSPACE SERIES - PROCEDURE FOR INSPECTION, TESTING AND ACCEPTANCE OF WROUGHT STEELS (OTHER THAN PLATE, SHEET, STRIP AND TUBE)
    BS M46(1974) : LATEST
    SAE AMS 2750 : 2012 PYROMETRY
    BS EN ISO 3651-2 : 1998 DETERMINATION OF RESISTANCE TO INTERGRANULAR CORROSION OF STAINLESS STEELS - FERRITIC, AUSTENITIC AND FERRITIC-AUSTENITIC (DUPLEX) STAINLESS STEELS - CORROSION TEST IN MEDIA CONTAINING SULFURIC ACID
    BS 1134-1(1988) : 1988 ASSESSMENT OF SURFACE TEXTURE - PART 1: METHODS AND INSTRUMENTATION
    BS 1134-2(1990) : 1990 ASSESSMENT OF SURFACE TEXTURE - PART 2: GUIDANCE AND GENERAL INFORMATION
    BS EN ISO 8492:2013 Metallic materials. Tube. Flattening test
    BS 7773(1995) : 1995 CODE OF PRACTICE FOR CLEANING AND PREPARATION OF METAL SURFACES
    BS EN 2002-1 : 2005 AEROSPACE SERIES - METALLIC MATERIALS - TEST METHODS - PART 1: TENSILE TESTING AT AMBIENT TEMPERATURE
    BS EN ISO 3887:2003 STEELS - DETERMINATION OF DEPTH OF DECARBURIZATION
    BS 4A 4:1966 TEST PIECES AND TEST METHODS FOR METALLIC MATERIALS FOR AIRCRAFT - METRIC UNITS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective