We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS 733-1:1983

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Available format(s):  Hardcopy, PDF

    Superseded date:  15-08-1999

    Language(s):  English

    Published date:  01-01-1983

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National foreword
    Committees responsible
    Specification
    1 Scope and field of application
    2 Basis of adjustment
    3 Types and series of sizes
    4 Definitions of capacity
    5 Difference between actual capacity and nominal
        capacity
    6 Construction
    7 Graduation lines
    8 Inscriptions
    9 Visibility of graduation lines, figures and
        inscriptions
    Annex
    Device for adjusting the liquid level in a Reischauer-
    type pyknometer
    Tables
    1 Types and sizes of pyknometers
    2 Dimensional requirements for pyknometer tubes
    3 Dimensional requirements for pyknometer flasks
    Figures
    1 Type 1 (Lipkin)
    2 Type 2 (Sprengel)
    3 Type 3 (Gay-Lussac)
    4 Type 4 (Reischauer)
    5 Type 5 (Hubbard)
    6 Draw-off needle
    7 Filling needle

    Abstract - (Show below) - (Hide below)

    Describes requirements for an internationally acceptable series of pyknometers for general laboratory use for determination of densities of liquids. Excludes specialized pyknometers for particular products and those not commonly used. Sufficient details to define such pyknometers should be included in International Standards describing their use. A device suitable for adjusting the liquid level in the neck of the Reischauer pyknometer is shown.

    General Product Information - (Show below) - (Hide below)

    Committee LBC/27
    Development Note BS DRAFT 97/122093 DC REFERS TO A REVISION
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS 6696:1986 METHODS FOR USE AND TESTING OF CAPACITY OF VOLUMETRIC GLASSWARE
    BS 1377-1:1990 METHODS OF TEST FOR SOILS FOR CIVIL ENGINEERING PURPOSES - PART 1: GENERAL REQUIREMENTS AND SAMPLE PREPARATION
    BS 684-1.1:1985 METHODS OF ANALYSIS OF FATS AND FATTY OILS - PHYSICAL METHODS - DETERMINATION OF LITRE WEIGHT IN AIR
    BS 6043-2.6:1986 METHODS OF SAMPLING AND TEST FOR CARBONACEOUS MATERIALS USED IN ALUMINIUM MANUFACTURE - ELECTRODE COKE - DETERMINATION OF THE DENSITY IN XYLENE OF CALCINED COKES
    BS 1377-2:1990 Methods of test for soils for civil engineering purposes Classification tests
    BS 4522:1988 (published 1988-12) Method for determination of absolute density at 20C of liquid chemical products for industrial use
    BS 3591:1985 (published 1985-10) Specification for industrial methylated spirits
    BS 507:1985 (published 1985-11) Specification for ethanol for industrial use
    BS 5600-3.2:1988 Powder metallurgical materials and products. Methods of testing sintered metal materials and products, excluding hardmetals Determination of density, oil content and open porosity
    BS 733-2:1987 Pyknometers Methods for calibration and use of pyknometers
    BS 1016-108.5:1992 METHODS FOR ANALYSIS AND TESTING OF COAL AND COKE - TESTS SPECIAL TO COKE - DETERMINATION OF DENSITY AND POROSITY

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 383:1976 Laboratory glassware — Interchangeable conical ground joints
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective
Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more