We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS 8010-2.8:1992

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    CODE OF PRACTICE FOR PIPELINES - PIPELINES ON LAND: DESIGN, CONSTRUCTION AND INSTALLATION

    Available format(s):  Hardcopy, PDF

    Superseded date:  23-12-2003

    Language(s):  English

    Published date:  01-01-1992

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Committees responsible
    Foreword
    Code of practice
    Section 1. General
    1.1 Scope
    1.2 References
    1.3 Definitions
    1.4 Units
    1.5 Application
    1.6 Pipeline and plant area demarcations
    1.7 Safety
    1.8 Environmental protection
    1.9 Quality assurance
    1.10 Statutory requirements
    1.11 Documentation
    1.12 Abandonment
    1.13 Pipeline design flowchart
    Section 2. Design
    2.1 Safety considerations
    2.2 Categorization of substances
    2.3 Safety evaluation
    2.4 Classification of location
    2.5 Selection of design factor
    2.6 General design considerations
    2.7 Design conditions
    2.8 Design criteria
    2.9 Pressure, thermal and other stress criteria
    2.10 Limits of calculated stress
    2.11 Corrosion allowance
    2.12 Fatigue life
    2.13 Thermal insulation
    2.14 Supports and anchors
    Section 3. Materials
    3.1 General requirements, materials and dimensional
          standards
    3.2 Limitations on materials
    3.3 Pipe
    3.4 Pipe without full certification
    3.5 Pipe fittings, components and bends
    3.6 Quality assurance
    Section 4. Corrosion protection
    4.1 General
    4.2 External corrosion
    4.3 Internal corrosion
    4.4 Cathodic protection
    Section 5. Terminals and intermediate stations
    5.1 General
    5.2 Location
    5.3 Hazardous area classification
    5.4 Piping
    5.5 Vibration resonance and noise
    5.6 Heating and cooling stations
    5.7 Interface detection
    5.8 Safety systems
    Section 6. Construction
    6.1 General
    6.2 Construction supervision
    6.3 Safety
    6.4 Setting out and surveying for bends
    6.5 Handling and storage of pipe
    6.6 Pipe stringing, field bending and swabbing
    6.7 Pipe inspection
    6.8 Welding
    6.9 Joint wrapping and trench excavation
    6.10 Coating inspection and holiday detection
    6.11 Lowering
    6.12 Backfilling and reinstatement
    6.13 Coating survey following construction
    6.14 Crossings
    6.15 Cleaning and gauging
    6.16 Tie-in welds
    6.17 Pups
    Section 7. Quality assurance
    7.1 General
    7.2 Basic terms
    7.3 Design quality assurance
    7.4 Materials quality assurance
    7.5 Construction quality assurance
    7.6 Records and document control
    Section 8. Pressure testing
    8.1 Introduction
    8.2 Safety precautions
    8.3 Test equipment
    8.4 Test pressure
    8.5 Test procedure
    8.6 Test acceptance criteria
    8.7 High level testing
    8.8 Disposal of test water
    8.9 Repairs to test failures
    8.10 Tie-in welds
    8.11 Pre-testing of crossings
    8.12 Testing of fabricated components
    8.13 Test records
    Section 9. Commissioning
    9.1 General
    9.2 Precommissioning
    9.3 Cleaning
    9.4 Commissioning
    9.5 Deferred commissioning
    9.6 Communications
    9.7 Handover procedures
    Tables
    1 Pipeline design flowchart
    2 Substance factors
    3 Pipe specified minimum yield strength (Sy)
    4 Factors for hoop stress variations
    5 Standards for materials
    Figures
    1 Extent of pipeline systems for conveying oil and
          gas which are covered by this Section
    2 Minimum distance from normally occupied buildings
          for methane (a category D substance)
    3 Pressure definitions
    4 Measurement of air content
    5 Effect of temperature on pressure
    List of references

    Abstract - (Show below) - (Hide below)

    Gives advice on the construction, installation and design of steel pipelines on land for gas, oil and toxic fluids. Not meant to duplicate or replace mechanical, hydraulic or structural design manuals. Coverage includes materials, corrosion protection, terminals and intermediate stations, quality assurance, pressure testing and commissioning. Also includes tables and diagrams.

    General Product Information - (Show below) - (Hide below)

    Committee B/203
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    ISO/TS 24817:2006 Petroleum, petrochemical and natural gas industries Composite repairs for pipework Qualification and design, installation, testing and inspection
    I.S. EN 1993-4-3:2007 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 4-3: PIPELINES
    EEMUA 177 : 2000 GUIDE TO THE UK PRESSURE SYSTEM SAFETY REGULATIONS (2000)
    DD ISO/TS 24817 : 2006 PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION
    BS 8010-3:1993 CODE OF PRACTICE FOR PIPELINES - PIPELINES SUBSEA: DESIGN, CONSTRUCTION AND INSTALLATION

    Standards Referencing This Book - (Show below) - (Hide below)

    BS 5493:1977 CODE OF PRACTICE FOR PROTECTIVE COATING OF IRON AND STEEL STRUCTURES AGAINST CORROSION
    ASME PV CODE 8 DIV 2 : 2017 BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 2- ALTERNATIVE RULES
    BS 8010-1:1989 CODE OF PRACTICE FOR PIPELINES - PIPELINES ON LAND: GENERAL
    EEMUA 153 : 96 AMD 1 2002 PROCESS PIPING - EEMUA SUPPLEMENT TO ASME B31.3 - 1996 EDITION
    BS 5839-1:1988 FIRE DETECTION AND ALARM SYSTEMS FOR BUILDINGS - CODE OF PRACTICE FOR SYSTEM DESIGN, INSTALLATION AND SERVICING
    ASME PV CODE 8 DIV 1 : 2017 BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1
    ASME B31.8 : 2016 Gas Transmission and Distribution Piping Systems
    BS 5306-6.1:1988 FIRE EXTINGUISHING INSTALLATIONS AND EQUIPMENT ON PREMISES - PART 6: FOAM SYSTEMS - SECTION 6.1: SPECIFICATION FOR LOW EXPANSION FOAM SYSTEMS
    ASME B31.3:2016 PROCESS PIPING
    API std 602 : 2015 GATE, GLOBE, AND CHECK VALVES FOR SIZES DN 100 (NPS 4) AND SMALLER FOR THE PETROLEUM AND NATURAL GAS INDUSTRIES
    API STD 600 : 2015 STEEL GATE VALVES - FLANGED AND BUTT-WELDING ENDS, BOLTED BONNETS
    BS 1873:1975 SPECIFICATION FOR STEEL GLOBE AND GLOBE STOP AND CHECK VALVES (FLANGED AND BUTT WELDING ENDS) FOR THE PETROLEUM, PETROCHEMICAL AND ALLIED INDUSTRIES
    BS 1965-1:1963 SPECIFICATION FOR BUTT-WELDING PIPE FITTINGS FOR PRESSURE PURPOSES - CARBON STEEL
    API 5L : 2012 LINE PIPE
    BS 6759-3:1984 SAFETY VALVES - SPECIFICATION FOR SAFETY VALVES FOR PROCESS FLUIDS
    API 597 : 3ED 81 STEEL VENTURI GATE VALVES
    BS CP3009(1970) : AMD 3340 THERMALLY INSULATED UNDERGROUND PIPING SYSTEMS
    BS 1832:1991 SPECIFICATION FOR COMPRESSED ASBESTOS FIBRE JOINTING
    API 599 : 2013 METAL PLUG VALVES - FLANGED, THREADED, AND WELDING ENDS
    EI MODEL CODE SAFE PRACTICE PT2 : 3ED 2013 DESIGN, CONSTRUCTION AND OPERATION OF PETROLEUM DISTRIBUTION INSTALLATIONS
    BS 5306-6.2:1989 FIRE EXTINGUISHING INSTALLATIONS AND EQUIPMENT ON PREMISES - FOAM SYSTEMS - SPECIFICATION FOR MEDIUM AND HIGH EXPANSION FOAM SYSTEMS
    BS 3602-1:1987 STEEL PIPES AND TUBES FOR PRESSURE PURPOSES: CARBON AND CARBON MANGANESE STEEL WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES - SPECIFICATION FOR SEAMLESS AND ELECTRIC RESISTANCE WELDED INCLUDING WELDED TUBES
    MSS SP 44 : 2016 STEEL PIPELINE FLANGES
    API 6D :2015 SPECIFICATION FOR PIPELINE AND PIPING VALVES
    ASME B16.5 : 2017 PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD
    ASME PV CODE 2B : 2017 BOILER AND PRESSURE VESSEL CODE - MATERIALS - NONFERROUS MATERIAL SPECIFICATIONS
    ASME PV CODE 2A : 2017 BOILER AND PRESSURE VESSEL CODE - MATERIALS - FERROUS MATERIAL SPECIFICATIONS (BEGINNING TO SA-450) AND (SA-451 TO END)
    MSS SP 75 : 2014 HIGH-STRENGTH, WROUGHT, BUTT-WELDING FITTINGS
    ASME PV CODE 2D CUSTOMARY : 2017 BOILER AND PRESSURE VESSEL CODE - MATERIALS - PROPERTIES (CUSTOMARY)
    BS 3293:1960 SPECIFICATION FOR CARBON STEEL PIPE FLANGES (OVER 24 INCHES NOMINAL SIZE) FOR THE PETROLEUM INDUSTRY
    BS 1868(1975) : 1975 SPECIFICATION FOR STEEL CHECK VALVES (FLANGED AND BUTT-WELDING ENDS) FOR THE PETROLEUM, PETROCHEMICAL AND ALLIED INDUSTRIES
    BS 5306-3:1985 FIRE EXTINGUISHING INSTALLATIONS AND EQUIPMENT ON PREMISES - CODE OF PRACTICE FOR SELECTION INSTALLATION AND MAINTENANCE OF PORTABLE FIRE EXTINGUISHERS
    ASME PV CODE 2C : 2017 BOILER AND PRESSURE VESSEL CODE - MATERIALS - SPECIFICATIONS FOR WELDING RODS, ELECTRODES, AND FILLER METALS
    BS 2815(1973) : 1973 SPECIFICATION FOR COMPRESSED ASBESTOS FIBRE JOINTING
    BS 7361-1:1991 CATHODIC PROTECTION - PART 1: CODE OF PRACTICE FOR LAND AND MARINE APPLICATIONS
    BS 1504:1976 SPECIFICATION FOR STEEL CASTINGS FOR PRESSURE PURPOSES
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective
Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more