BS EN 10217-7:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Welded steel tubes for pressure purposes. Technical delivery conditions Stainless steel tubes
Hardcopy , PDF
14-05-2021
English
31-10-2014
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Classification and designation
6 Information to be supplied by the purchaser
7 Manufacturing process
8 Requirements
9 Inspection
10 Sampling
11 Verification test methods
12 Marking
13 Handling and packaging
Annex A (informative) - Technical changes from the previous
edition
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of
EU Directive 97/23/EC
Defines the technical delivery conditions in two test categories for welded tubes of circular cross-section made of austenitic and austenitic-ferritic stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures.
This Part of EN10217 specifies the technical delivery conditions in two test categories for welded tubes of circular cross-section made of austenitic and austenitic-ferritic stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures. NOTE Once this standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC , pressure equipment directive, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 97/23/EC is limited to technical data of materials in this standard and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which may affect properties of the base materials.
| Committee |
ISE/110
|
| DevelopmentNote |
Supersedes 99/701076 DC and BS 3605-2(1992). (02/2005) Supersedes 09/30207521 DC. (11/2014)
|
| DocumentType |
Standard
|
| Pages |
40
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN 10217-7:2014 | Identical |
| NBN EN 10217-7 : 2014 | Identical |
| NEN EN 10217-7 : 2014 | Identical |
| NF EN 10217-7 : 2015 | Identical |
| UNE-EN 10217-7:2006 | Identical |
| UNI EN 10217-7 : 2014 | Identical |
| DIN EN 10217-7:2015-01 | Identical |
| NS EN 10217-7 : 2014 | Identical |
| I.S. EN 10217-7:2014 | Identical |
| ONORM EN 10217-7 : 2014 | Identical |
| BS 8525-1:2010 | Greywater systems Code of practice |
| 13/30199128 DC : 0 | BS 6891 - SPECIFICATION FOR THE INSTALLATION AND MAINTENANCE OF LOW PRESSURE GAS INSTALLATION PIPEWORK OF UP TO 35 MM (R1[1/4]) IN PREMISES |
| 08/30171875 DC : DRAFT JUNE 2008 | BS 8515 - CODE OF PRACTICE FOR RAINWATER HARVESTING SYSTEMS |
| BS 4825-1(1991) : 1991 | STAINLESS STEEL TUBES AND FITTINGS FOR THE FOOD INDUSTRY AND OTHER HYGIENIC APPLICATIONS - PART 1: SPECIFICATION FOR TUBES |
| DEFSTAN 02-357(PT4)/1(2010) : 2010 | REQUIREMENTS FOR GASEOUS FIREFIGHTING SYSTEMS FOR MAIN AND AUXILIARY MACHINERY SPACES ON SURFACE SHIPS - PART 4: GENERAL REQUIREMENTS FOR INERT GAS SYSTEMS INCLUDING ELECTRIC/ELECTRONIC SPACES |
| 16/30353337 DC : 0 | PD 5500:2015+A3 - SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| 11/30244843 DC : 0 | BS 5306-4:2001+A1 - FIRE EXTINGUISHING INSTALLATIONS AND EQUIPMENT ON PREMISES - PART 4: SPECIFICATION FOR CARBON DIOXIDE SYSTEMS |
| BS 8515(2009) : 2009 | RAINWATER HARVESTING SYSTEMS - CODE OF PRACTICE |
| BS PD5500(2015) : 2015 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| BS 5306-4(2001) : 2001 | FIRE EXTINGUISHING INSTALLATIONS AND EQUIPMENT ON PREMISES - PART 4: SPECIFICATION FOR CARBON DIOXIDE SYSTEMS |
| BS 6739:2009 | Code of practice for instrumentation in process control systems: installation design and practice |
| BS PD5500(2009) : 2009 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| BS 6891:2015 | Specification for the installation and maintenance of low pressure gas installation pipework of up to 35 mm (R1¼) on premises |
| BS 6180:2011 | Barriers in and about buildings. Code of practice |
| BS PD5500(2006) : 2006 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| BS PD5500(2018) : 2018 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| BS PD5500(2012) : 2012 | SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS |
| BS 5306-4:2001+A1:2012 | Fire extinguishing installations and equipment on premises Specification for carbon dioxide systems |
| 09/30184122 DC : 0 | BS 8525-1 - GREYWATER SYSTEMS - PART 1: CODE OF PRACTICE |
| 10/30212801 DC : 0 | BS 6180 - BARRIERS IN AND ABOUT BUILDINGS - CODE OF PRACTICE |
| 08/30136724 DC : DRAFT MAY 2008 | BS 6739 - CODE OF PRACTICE FOR INSTRUMENTATION IN PROCESS CONTROL SYSTEMS - INSTALLATION DESIGN AND PRACTICE |
| EN ISO 14284:2002 | Steel and iron - Sampling and preparation of samples for the determination of chemical composition (ISO 14284:1996) |
| EN 10052:1993 | Vocabulary of heat treatment terms for ferrous products |
| ISO 8496:2013 | Metallic materials Tube Ring tensile test |
| EN ISO 8493 : 2004 | Metallic materials - Tube - Drift-expanding test (ISO 8493:1998) |
| EN 10027-2:2015 | DESIGNATION SYSTEMS FOR STEELS - PART 2: NUMERICAL SYSTEM |
| EN ISO 10893-11:2011 | Non-destructive testing of steel tubes - Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections (ISO 10893-11:2011) |
| CEN/TR 10261:2013 | Iron and steel - European standards for the determination of chemical composition |
| ISO 10893-9:2011 | Non-destructive testing of steel tubes Part 9: Automated ultrasonic testing for the detection of laminar imperfections in strip/plate used for the manufacture of welded steel tubes |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| ISO 9712:2012 | Non-destructive testing Qualification and certification of NDT personnel |
| EN ISO 10893-10:2011 | Non-destructive testing of steel tubes - Part 10: Automated full peripheral ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of longitudinal and/or transverse imperfections (ISO 10893-10:2011) |
| EN ISO 5173:2010/A1:2011 | DESTRUCTIVE TESTS ON WELDS IN METALLIC MATERIALS - BEND TESTS (ISO 5173:2009) |
| EN ISO 8495:2013 | Metallic materials - Tube - Ring-expanding test (ISO 8495:2013) |
| ISO 10893-1:2011 | Non-destructive testing of steel tubes Part 1: Automated electromagnetic testing of seamless and welded (except submerged arc-welded) steel tubes for the verification of hydraulic leaktightness |
| EN ISO 377:2017 | Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:2017) |
| ISO 2566-2:1984 | Steel Conversion of elongation values Part 2: Austenitic steels |
| ISO 10893-8:2011 | Non-destructive testing of steel tubes Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar imperfections |
| EN ISO 8496:2013 | Metallic materials - Tube - Ring tensile test (ISO 8496:2013) |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| EN ISO 10893-1:2011 | Non-destructive testing of steel tubes - Part 1: Automated electromagnetic testing of seamless and welded (except submerged arc-welded) steel tubes for the verification of hydraulic leaktightness (ISO 10893-1:2011) |
| ISO 10893-11:2011 | Non-destructive testing of steel tubes Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections |
| EN 10168:2004 | Steel products - Inspection documents - List of information and description |
| ISO 8493:1998 | Metallic materials Tube Drift-expanding test |
| EN ISO 10893-8:2011 | Non-destructive testing of steel tubes - Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar imperfections (ISO 10893-8:2011) |
| ISO 5173:2009 | Destructive tests on welds in metallic materials — Bend tests |
| EN ISO 9712:2012 | Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2012) |
| EN 10028-7:2016 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
| EN ISO 1127:1996 | Stainless steel tubes - Dimensions, tolerances and conventional masses per unit length (ISO 1127:1992) |
| ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
| EN ISO 10893-7:2011 | Non-destructive testing of steel tubes - Part 7: Digital radiographic testing of the weld seam of welded steel tubes for the detection of imperfections (ISO 10893-7:2011) |
| EN ISO 10893-6:2011 | Non-destructive testing of steel tubes - Part 6: Radiographic testing of the weld seam of welded steel tubes for the detection of imperfections (ISO 10893-6:2011) |
| EN 10021:2006 | General technical delivery conditions for steel products |
| EN ISO 10893-2:2011 | Non-destructive testing of steel tubes - Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections (ISO 10893-2:2011) |
| ISO 3651-2:1998 | Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in media containing sulfuric acid |
| EN ISO 10893-9:2011 | Non-destructive testing of steel tubes - Part 9: Automated ultrasonic testing for the detection of laminar imperfections in strip/plate used for the manufacture of welded steel tubes (ISO 10893-9:2011) |
| ISO 857-1:1998 | Welding and allied processes Vocabulary Part 1: Metal welding processes |
| EN ISO 2566-2:1999 | Steel - Conversion of elongation values - Part 2: Austenitic steels (ISO 2566-2:1984) |
| ISO 8495:2013 | Metallic materials Tube Ring-expanding test |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN ISO 6892-2:2011 | Metallic materials - Tensile testing - Part 2: Method of test at elevated temperature (ISO 6892-2:2011) |
| EN ISO 3651-2 : 1998 | DETERMINATION OF RESISTANCE TO INTERGRANULAR CORROSION OF STAINLESS STEELS - FERRITIC, AUSTENITIC AND FERRITIC-AUSTENITIC (DUPLEX) STAINLESS STEELS - CORROSION TEST IN MEDIA CONTAINING SULFURIC ACID |
| ISO 11484:2009 | Steel products — Employer's qualification system for non-destructive testing (NDT) personnel |
| EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
| ISO 8492:2013 | Metallic materials Tube Flattening test |
| ISO 6892-2:2011 | Metallic materials Tensile testing Part 2: Method of test at elevated temperature |
| EN 10020:2000 | Definition and classification of grades of steel |
| ISO 10893-6:2011 | Non-destructive testing of steel tubes Part 6: Radiographic testing of the weld seam of welded steel tubes for the detection of imperfections |
| EN ISO 8492:2013 | Metallic materials - Tube - Flattening test (ISO 8492:2013) |
| ISO 10893-2:2011 | Non-destructive testing of steel tubes Part 2: Automated eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections |
| EN ISO 148-1:2016 | Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016) |
| EN 10266:2003 | Steel tubes, fittings and structural hollow sections - Symbols and definitions of terms for use in product standards |
| ISO 10893-7:2011 | Non-destructive testing of steel tubes Part 7: Digital radiographic testing of the weld seam of welded steel tubes for the detection of imperfections |
| ISO 10893-10:2011 | Non-destructive testing of steel tubes Part 10: Automated full peripheral ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of longitudinal and/or transverse imperfections |
| ISO 377:2017 | Steel and steel products — Location and preparation of samples and test pieces for mechanical testing |
| ISO 14284:1996 | Steel and iron — Sampling and preparation of samples for the determination of chemical composition |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| ISO 1127:1992 | Stainless steel tubes Dimensions, tolerances and conventional masses per unit length |
| 1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.