We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS EN 10226-1:2004

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    Pipe threads where pressure tight joints are made on the threads Taper external threads and parallel internal threads. Dimensions, tolerances and designation

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  31-10-2010

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Symbols and explanations
    5 Dimensions
    6 Designation
    7 Thread design
      7.1 Thread form
      7.2 Thread lengths
    8 Gauging
    9 Combination with fastening thread
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes the requirements for thread form, dimensions, tolerances and designation for jointing pipe threads, sizes 1/16 to 6 inclusive, for joints made pressure-tight by the mating of the threads.

    General Product Information - (Show below) - (Hide below)

    Committee ISE/110
    Development Note Supersedes 95/714856 DC (08/2004) Together with BS EN 10226-2 and BS EN 10226-3, it supersedes BS 21(1985). (04/2016)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    13/30199128 DC : 0 BS 6891 - SPECIFICATION FOR THE INSTALLATION AND MAINTENANCE OF LOW PRESSURE GAS INSTALLATION PIPEWORK OF UP TO 35 MM (R1[1/4]) IN PREMISES
    DEFSTAN 23-13(PT3)/1(2014) : 2014 GENERIC BASE ARCHITECTURE (GBA) - PART 3: WATER
    BS 9251:2014 FIRE SPRINKLER SYSTEMS FOR DOMESTIC AND RESIDENTIAL OCCUPANCIES - CODE OF PRACTICE
    BS 5306-4(2001) : 2001 FIRE EXTINGUISHING INSTALLATIONS AND EQUIPMENT ON PREMISES - PART 4: SPECIFICATION FOR CARBON DIOXIDE SYSTEMS
    BS 5991:2006 SPECIFICATION FOR INDIRECT GAS FIRED FORCED CONVECTION AIR HEATERS WITH RATED HEAT INPUTS GREATER THAN 330 KW BUT NOT EXCEEDING 2 MW FOR INDUSTRIAL AND COMMERCIAL SPACE HEATING - SAFETY AND PERFORMANCE REQUIREMENTS (EXCLUDING ELECTRICAL REQUIREMENTS) (2ND FAMILY GASES)
    BS 6891:2015 SPECIFICATION FOR THE INSTALLATION AND MAINTENANCE OF LOW PRESSURE GAS INSTALLATION PIPEWORK OF UP TO 35 MM (R1[1/4]) ON PREMISES
    BS 5990:2006 SPECIFICATION FOR DIRECT GAS-FIRED FORCED CONVECTION AIR HEATERS WITH RATED HEAT INPUTS GREATER THAN 330 KW BUT NOT EXCEEDING 2 MW FOR INDUSTRIAL AND COMMERCIAL SPACE HEATING - SAFETY AND PERFORMANCE REQUIREMENTS (EXCLUDING ELECTRICAL REQUIREMENTS) (2ND FAMILY GASES)
    BS 6891(2005) : 2005 INSTALLATION OF LOW PRESSURE GAS PIPEWORK OF UP TO 35 MM (R1[1/4]) IN DOMESTIC PREMISES (2ND FAMILY GAS) - SPECIFICATION
    BS 5306-4:2001+A1:2012 Fire extinguishing installations and equipment on premises Specification for carbon dioxide systems
    FM 1056 : 2010 SIGHT DRAINS FOR AUTOMATIC SPRINKLER SYSTEMS
    BS 8487(2007) : 2007 THE DESIGN AND CONSTRUCTION OF GAS BOOSTERS USED IN ASSOCIATION WITH COMBUSTION EQUIPMENT - SPECIFICATION
    14/30280481 DC : 0 BS 9251 - FIRE SPRINKLER SYSTEMS FOR DOMESTIC AND RESIDENTIAL OCCUPANCIES - CODE OF PRACTICE
    BS 853-1:1990+A3:2011 (published 2011-09) Specification for vessels for use in heating systems Calorifiers and storage vessels for central heating and hot water supply
    CSA/ANSI LC 6:08 (R2018) Natural gas operated diaphragm pumps

    Standards Referencing This Book - (Show below) - (Hide below)

    EN ISO 228-1 : 2003 PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION
    ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
    ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective
Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more