BS EN 1303:2015
Current
The latest, up-to-date edition.
Building hardware. Cylinders for locks. Requirements and test methods
Hardcopy , PDF
English
30-06-2015
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Test - General and test apparatus
6 Test methods - procedures
7 Classification
8 Marking
Annex A (normative) - Cylinders suitable for use
on fire resistant / smoke control doors
Annex B (informative) - Tables of test sequence
Annex C (informative) - Product information
Annex D (informative) - Manufacturer's declaration of
compliance
Annex E (informative) - Comparison table between
EN 1303:2005 and EN 1303:2015
Bibliography
Pertains to cylinders and their keys for such locks as are normally used in buildings and are designed to be used with cylinders, where the locks have an operational torque of maximum 1,2 Nm.
This European Standard applies to cylinders and their keys for such locks as are normally used in buildings and are designed to be used with cylinders, where the locks have an operational torque of maximum 1,2Nm. This European Standard specifies performance and other requirements for the strength, security, durability, performance and corrosion resistance of cylinders and their original keys. It establishes one category of use, three grades of durability, three grades for fire and four grades corrosion resistance all based on performance tests as well as six grades of key related security based on design requirements and five grades on performance tests that simulate attack. This European Standard includes tests of satisfactory operation at a range of temperatures. It specifies test methods to be used on cylinders and their protective measures linked with these cylinders and recommended by the manufacturer. Corrosion resistance is specified by reference to the requirements of EN1670 on corrosion resistance of building hardware. The suitability of cylinders for use on fire or smoke-door assemblies is determined by fire performance tests conducted in addition to the performance testing required by this standard. Since suitability for use on fire doors is not essential in every situation the manufacturer has the option to state if the cylinder conforms to these additional requirements or not. If so claimed, cylinders will comply with the requirements in AnnexA. On occasions there may be a need for additional functions within the design of the cylinder. Purchasers should satisfy themselves that the products are suitable for their intended use.
| Committee |
B/538/4
|
| DevelopmentNote |
Supersedes BS 3621(1980) and 94/101249 DC Also available as part of BS KIT 114 (03/2005) Supersedes 13/30264195 DC. (06/2015)
|
| DocumentType |
Standard
|
| Pages |
38
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| SN EN 1303 : 2015 | Identical |
| NBN EN 1303 : 2005 COR 2008 | Identical |
| NF EN 1303 : 2015 | Identical |
| UNE-EN 1303:2016 | Identical |
| DIN EN 1303:2015-08 | Identical |
| UNI EN 1303 : 2005 | Identical |
| I.S. EN 1303:2015 | Identical |
| EN 1303:2015 | Identical |
| NEN EN 1303 : 2015 | Identical |
| NS EN 1303 : 1998 | Identical |
| 16/30338194 DC : 0 | BS 10621 - LOCK ASSEMBLIES IN WHICH THE OPERATING MODE CAN BE SWITCHED BETWEEN THE NORMAL BS 8621 OPERATING MODE AND A SECURE MODE IN WHICH NO EGRESS IS POSSIBLE |
| 13/30277228 DC : 0 | BS 8607 - MECHANICALLY OPERATED PUSH-BUTTON LOCKSETS - REQUIREMENTS AND TEST METHODS |
| 16/30332500 DC : 0 | BS 8214 - TIMBER-BASED FIRE DOOR ASSEMBLIES - CODE OF PRACTICE |
| BS 10621(2007) : 2007 | THIEF RESISTANT DUAL-MODE LOCK ASSEMBLY |
| 16/30338192 DC : 0 | BS 8621 - LOCK ASSEMBLIES OPERATED BY KEY FROM THE OUTSIDE OF THE DOOR AND BY HANDLE OR THUMB TURN FROM THE INSIDE OF THE DOOR |
| BS 3621:1998 | Specification for thief resistant locks |
| BS 8214:2016 | Timber-based fire door assemblies. Code of practice |
| BS 3621(2007) : 2007 | THIEF RESISTANT LOCK ASSEMBLY - KEY EGRESS |
| BS 10621:2017 | Lock assemblies in which the operating mode can be switched between the normal BS 8621 operating mode and a secure mode in which no egress is possible |
| BS 8621(2007) : 2007 | THIEF RESISTANT LOCK ASSEMBLY - KEYLESS EGRESS |
| BS 3621:2004 | Thief resistant lock assembly. Key egress |
| BS 8607(2014) : 2014 | MECHANICALLY OPERATED PUSH BUTTON LOCKSETS - REQUIREMENTS AND TEST METHODS |
| 07/30167591 DC : 0 | BS 10621 - THIEF RESISTANT DUAL-MODE LOCK ASSEMBLIES |
| 15/30330077 DC : 0 | PAS 24 - ENHANCED SECURITY PERFORMANCE REQUIREMENTS FOR DOORSETS AND WINDOWS IN THE UK - EXTERNAL DOORSETS AND WINDOWS INTENDED TO OFFER A LEVEL OF SECURITY SUITABLE FOR DWELLINGS AND OTHER BUILDINGS EXPOSED TO COMPARABLE RISK |
| 06/30158054 DC : DRAFT NOV 2006 | BS 3621 AMD 1 - THIEF RESISTANT LOCK ASSEMBLY - KEY EGRESS |
| BS PAS 24-1(1999) : 1999 AMD 16981 | ENHANCED SECURITY PERFORMANCE REQUIREMENTS FOR DOOR ASSEMBLIES - PART 1: SINGLE AND DOUBLE LEAF, HINGED EXTERNAL DOOR ASSEMBLIES TO DWELLINGS |
| BS PAS 24(2007) : 2007 | ENHANCED SECURITY PERFORMANCE REQUIREMENTS FOR DOOR ASSEMBLIES - SINGLE AND DOUBLE LEAF, HINGED EXTERNAL DOOR ASSEMBLIES TO DWELLINGS |
| BS 8300(2009) : 2009 | DESIGN OF BUILDINGS AND THEIR APPROACHES TO MEET THE NEEDS OF DISABLED PEOPLE - CODE OF PRACTICE |
| 17/30335834 DC : 0 | BS 8300-2 - DESIGN OF AN ACCESSIBLE AND INCLUSIVE BUILT ENVIRONMENT - PART 2: BUILDINGS - CODE OF PRACTICE |
| BS PAS 10621(2011) : 2011 | MULTIPOINT LOCKING ASSEMBLIES - DUAL MODE EGRESS - PERFORMANCE REQUIREMENTS AND TEST METHODS |
| 04/30108696 DC : DRAFT APR 2004 | BS 8621 - THIEF RESISTANT LOCK AND LATCH ASSEMBLIES THAT ONLY ALLOW KEYLESS EGRESS |
| 16/30338190 DC : 0 | BS 3621 - LOCK ASSEMBLIES OPERATED BY KEY FROM BOTH THE INSIDE AND OUTSIDE OF THE DOOR |
| BS PAS 8621(2011) : 2011 | MULTIPOINT LOCKING ASSEMBLIES - KEYLESS EGRESS - PERFORMANCE REQUIREMENTS AND TEST METHODS |
| 04/30108691 DC : DRAFT APR 2004 | BS 3621 - THIEF RESISTANT LOCK AND LATCH ASSEMBLIES THAT ONLY ALLOW EGRESS USING A KEY |
| BS PAS 3621(2011) : 2011 | MULTIPOINT LOCKING ASSEMBLIES - KEYED EGRESS - PERFORMANCE REQUIREMENTS AND TEST METHODS |
| 11/30256242 DC : 0 | BS PAS 24 - ENHANCED SECURITY PERFORMANCE REQUIREMENTS FOR DOOR SETS AND WINDOWS IN THE UK - EXTERNAL DOOR SETS AND WINDOWS INTENDED TO OFFER A LEVEL OF SECURITY SUITABLE FOR DWELLINGS AND OTHER BUILDINGS EXPOSED TO COMPARABLE RISK |
| BS 8621:2004 | Thief resistant lock assembly. Keyless egress |
| BS PAS 40(2002) : 2002 | BANKNOTE THEFT DETERRENT SYSTEMS USING DYE OR SMOKE-DYE |
| 06/30158068 DC : DRAFT NOV 2006 | BS 8621 AMD 1 - THIEF RESISTANT LOCK ASSEMBLY - KEYLESS EGRESS |
| BS 3621:2017 | Lock assemblies operated by key from both the inside and outside of the door |
| BS 8621:2017 | Lock assemblies operated by key from the outside of the door and by handle or thumb turn from the inside of the door |
| EN 1906:2012 | Building hardware - Lever handles and knob furniture - Requirements and test methods |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| EN ISO 15481 : 1999 | CROSS RECESSED PAN HEAD DRILLING SCREWS WITH TAPPING SCREW THREAD (ISO 15481:1999) |
| ISO 15480:1999 | Hexagon washer head drilling screws with tapping screw thread |
| EN 1670:2007/AC:2008 | BUILDING HARDWARE - CORROSION RESISTANCE - REQUIREMENTS AND TEST METHODS |
| EN 1634-3:2004/AC:2006 | FIRE RESISTANCE AND SMOKE CONTROL TESTS FOR DOOR AND SHUTTER ASSEMBLIES, OPENABLE WINDOWS AND ELEMENTS OF BUILDING HARDWARE - PART 3: SMOKE CONTROL TEST FOR DOOR AND SHUTTER ASSEMBLIES |
| ISO 10666:1999 | Drilling screws with tapping screw thread — Mechanical and functional properties |
| EN ISO 15483 : 1999 | CROSS RECESSED RAISED COUNTERSUNK HEAD DRILLING SCREWS WITH TAPPING SCREW THREAD |
| EN 1634-2 : 2008 | Fire resistance and smoke control tests for door, shutter and openable window assemblies and elements of building hardware - Part 2: Fire resistance characterisation test for elements of building hardware |
| ISO 15481:1999 | Cross recessed pan head drilling screws with tapping screw thread |
| EN ISO 10666 : 1999 | DRILLING SCREWS WITH TAPPING SCREW THREAD - MECHANICAL AND FUNCTIONAL PROPERTIES |
| ISO 15483:1999 | Cross recessed raised countersunk head drilling screws with tapping screw thread |
| EN ISO 15482 : 1999 | CROSS RECESSED COUNTERSUNK HEAD DRILLING SCREWS WITH TAPPING SCREW THREAD |
| ISO 15482:1999 | Cross recessed countersunk head drilling screws with tapping screw thread |
| EN ISO 15480 : 1999 | HEXAGON WASHER HEAD DRILLING SCREWS WITH TAPPING SCREW THREAD |
| ISO 10899:1996 | High-speed steel two-flute twist drills — Technical specifications |
| EN 636:2012+A1:2015 | Plywood - Specifications |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.