Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS EN 13799:2012

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

LPG equipment and accessories. Contents gauges for Liquefied Petroleum Gas (LPG) pressure vessels
Available format(s)

Hardcopy , PDF

Superseded date

31-10-2022

Language(s)

English

Published date

30-04-2012

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Operating conditions
5 Materials
6 Design - General requirements
7 Design- Specific requirements
8 Design testing
9 Production testing and inspection
10 Marking
11 Documentation
Annex A (normative) - Float gauge flange and gasket
        dimensions
Annex B (normative) - Special low temperature
        requirements
Annex C (normative) - Production testing and inspection
Annex D (informative) - Vibration Testing
Annex E (informative) - Environment checklist
Bibliography

Describes minimum requirements for design and testing of contents gauges, which are directly connected to LPG transportable pressure vessels, LPG drums, LPG cylinders and static LPG pressure vessels above 0,5 l water capacity excluding those used for automotive containers.

This European Standard specifies minimum requirements for design and testing of contents gauges, which are directly connected to LPG transportable pressure vessels, LPG drums, LPG cylinders and static LPG pressure vessels above 0,5 l water capacity excluding those used for automotive containers. This European Standard does not apply to refineries or other process plants.

Committee
PVE/19
DevelopmentNote
Supersedes 00/704818 DC (11/2002) Supersedes 09/30205570 DC. (04/2012)
DocumentType
Standard
Pages
32
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
ONORM EN 13799 : 2012 Identical
UNI EN 13799 : 2012 Identical
SN EN 13799 : 2012 Identical
NF EN 13799 : 2012 Identical
DIN EN 13799:2012-06 Identical
NEN EN 13799 : 2012 Identical
EN 13799:2012 Identical
NBN EN 13799 : 2012 Identical
NS EN 13799 : 2012 Identical
I.S. EN 13799:2012 Identical
UNE-EN 13799:2012 Identical

EN 751-3:1996/AC:1997 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 3: Unsintered PTFE tapes
ISO 11114-1:2012 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials
EN 1503-4:2016 Valves - Materials for bodies, bonnets and covers - Part 4: Copper alloys specified in European Standards
EN 10270-3:2011 Steel wire for mechanical springs - Part 3: Stainless spring steel wire
EN 13906-1:2013 Cylindrical helical springs made from round wire and bar - Calculation and design - Part 1 : Compression springs
EN 60079-0:2012/A11:2013 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED)
MIL-STD-810 Revision G:2008 ENVIRONMENTAL ENGINEERING CONSIDERATIONS AND LABORATORY TESTS
EN 1503-3:2000/AC:2001 VALVES - MATERIALS FOR BODIES, BONNETS AND COVERS - PART 3: CAST IRONS SPECIFIED IN EUROPEAN STANDARDS
EN 1503-2:2000 Valves - Materials for bodies, bonnets and covers - Part 2: Steels other than those specified in European Standards
EN 751-2:1996 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 2: Non-hardening jointing compounds
EN 1503-1:2000 Valves - Materials for bodies, bonnets and covers - Part 1: Steels specified in European Standards
EN ISO 11114-1:2012/A1:2017 GAS CYLINDERS - COMPATIBILITY OF CYLINDER AND VALVE MATERIALS WITH GAS CONTENTS - PART 1: METALLIC MATERIALS (ISO 11114-1: 2012/AMD 1:2017)
ASME B1.20.1 : 2013(R2018) PIPE THREADS, GENERAL PURPOSE (INCH)
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
ISO 11114-2:2013 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 2: Non-metallic materials
EN ISO 11114-2:2013 Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2: Non-metallic materials (ISO 11114-2:2013)
EN 751-1:1996 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 1: Anaerobic jointing compounds
EN 1563:2011 Founding - Spheroidal graphite cast irons
EN 12420:2014 Copper and copper alloys - Forgings
EN 549:1994 Rubber materials for seals and diaphragms for gas appliances and gas equipment
EN 12165:2016 COPPER AND COPPER ALLOYS - WROUGHT AND UNWROUGHT FORGING STOCK
ISO 301:2006 Zinc alloy ingots intended for castings
ISO 6957:1988 Copper alloys Ammonia test for stress corrosion resistance
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
1994/9/EC : 1994 DIRECTIVE 94/9/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 23 MARCH 1994 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES
1997/23/EC : 1997 DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT

View more information
$407.85
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more