BS EN 14420-4:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
07-09-2022
English
31-07-2013
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Hose fittings with flanges
5 Dimensions, designations
6 Surface finish
7 Materials
8 Marking
9 Type testing and quality control
Bibliography
Describes requirements for hose tails according to EN 14420-2, with flanges of mating dimensions PN 10/PN 16/PN 25/PN 40 (according to nominal size and pressure stage) according to EN 1092-1, on hose fittings with clamp units according to EN 14420-3.
This European Standard specifies requirements for hose tails according to EN 14420-2, with flanges of mating dimensions PN 10/PN 16/PN 25/PN 40 (according to nominal size and pressure stage) according to EN 1092 1, on hose fittings with clamp units according to EN 14420-3. Maximum working pressure is 25 bar; maximum working temperature is 65 °C. Additionally, flanges are also usable according to EN 14422.
Committee |
PRI/66
|
DevelopmentNote |
Supersedes 02/121665 DC. (10/2005) Supersedes 06/30154637 DC. (06/2007)
|
DocumentType |
Standard
|
Pages |
20
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
UNE-EN 14420-4:2005 | Identical |
ONORM EN 14420-4 : 2013 | Identical |
NF EN 14420-4 : 2013 | Identical |
NEN EN 14420-4 : 2013 | Identical |
SN EN 14420-4:2013 | Identical |
NBN EN 14420-4 : 2013 | Identical |
UNI EN 14420-4 : 2013 | Identical |
NS EN 14420-4 : 2013 | Identical |
I.S. EN 14420-4:2013 | Identical |
EN 14420-4:2013 | Identical |
DIN EN 14420-4:2013-09 | Identical |
EN ISO 8330:2014 | Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330:2014) |
ISO 17636-1:2013 | Non-destructive testing of welds — Radiographic testing — Part 1: X- and gamma-ray techniques with film |
EN 22768-2:1993 | General tolerances - Part 2: Geometrical tolerances for features without individual tolerance indications (ISO 2768-2:1989) |
ISO 4042:1999 | Fasteners Electroplated coatings |
ISO 11666:2010 | Non-destructive testing of welds Ultrasonic testing Acceptance levels |
ISO 23277:2015 | Non-destructive testing of welds Penetrant testing Acceptance levels |
EN ISO 4042:1999 | FASTENERS - ELECTROPLATED COATINGS (ISO 4042:1999) |
ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its alloys |
EN 14420-1:2013 | Hose fittings with clamp units - Part 1: Requirements, types of fixing and connection, designation and testing |
EN 14422:2013 | Clamp type coupling assemblies for liquefied petroleum gas (LPG) transfer hoses |
EN 10087:1998 | Free-cutting steels - Technical delivery conditions for semi-finished products, hot-rolled bars and rods |
EN ISO 23278 : 2015 | NON-DESTRUCTIVE TESTING OF WELDS - MAGNETIC PARTICLE TESTING - ACCEPTANCE LEVELS (ISO 23278:2015) |
EN ISO 23277:2015 | Non-destructive testing of welds - Penetrant testing - Acceptance levels (ISO 23277:2015) |
ISO 6708:1995 | Pipework components Definition and selection of DN (nominal size) |
ISO 23278:2015 | Non-destructive testing of welds Magnetic particle testing Acceptance levels |
ISO 17640:2017 | Non-destructive testing of welds Ultrasonic testing Techniques, testing levels, and assessment |
EN 14420-2:2013 | Hose fittings with clamp units - Part 2: Hose side parts of hose tail |
ISO 8330:2007 | Rubber and plastics hoses and hose assemblies Vocabulary |
EN ISO 6708:1995 | Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995) |
EN 10283:2010 | Corrosion resistant steel castings |
ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
EN 1706:2010 | Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties |
EN ISO 23279:2017 | Non-destructive testing of welds - Ultrasonic testing - Characterization of discontinuities in welds (ISO 23279:2017) |
ISO 2768-2:1989 | GENERAL TOLERANCES - PART 2: GEOMETRICAL TOLERANCES FOR FEATURES WITHOUT INDIVIDUAL TOLERANCE INDICATIONS |
EN ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005) |
ISO 4200:1991 | Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length |
ISO 17636-2:2013 | Non-destructive testing of welds — Radiographic testing — Part 2: X- and gamma-ray techniques with digital detectors |
EN 22768-1:1993 | General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:1989) |
EN 10025-2:2004/AC:2005 | HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS |
EN ISO 17636-2:2013 | Non-destructive testing of welds - Radiographic testing - Part 2: X- and gamma-ray techniques with digital detectors (ISO 17636-2:2013) |
EN 14420-3:2013 | Hose fittings with clamp units - Part 3: Clamp units, bolted or pinned |
EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
EN 10083-2:2006 | Steels for quenching and tempering - Part 2: Technical delivery conditions for non alloy steels |
EN 10216-1:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties |
ISO 23279:2017 | Non-destructive testing of welds — Ultrasonic testing — Characterization of discontinuities in welds |
EN ISO 17636-1:2013 | Non-destructive testing of welds - Radiographic testing - Part 1: X- and gamma-ray techniques with film (ISO 17636-1:2013) |
EN ISO 17638:2016 | Non-destructive testing of welds - Magnetic particle testing (ISO 17638:2016) |
EN 573-3:2013 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products |
ISO 17638:2016 | Non-destructive testing of welds Magnetic particle testing |
EN 12163:2016 | Copper and copper alloys - Rod for general purposes |
EN 10217-1:2002/A1:2005 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - NON-ALLOY STEEL TUBES WITH SPECIFIED ROOM TEMPERATURE PROPERTIES |
EN 1435:1997/A2:2003 | NON-DESTRUCTIVE TESTING OF WELDS - RADIOGRAPHIC TESTING OF WELDED JOINTS |
EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.