Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS EN 1452-2 : 2000

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PLASTICS PIPING SYSTEMS FOR WATER SUPPLY - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 2: PIPES
Available format(s)

Hardcopy , PDF

Superseded date

31-01-2010

Language(s)

English

Published date

01-01-2000

Foreword
Introduction
1 Scope
2 Normative references
3 Definitions, symbols and abbreviations
4 Material
   4.1 Pipe material
   4.2 Density
   4.3 MRS-value
5 General characteristics
   5.1 Appearance
   5.2 Colour
   5.3 Opacity
6 Geometrical characteristics
   6.1 Measurement of dimensions
   6.2 Nominal outside diameters
   6.3 Mean outside diameters and their tolerances
   6.4 Wall thicknesses and their tolerances
   6.5 Length of pipe
   6.6 Pipes with sockets
   6.7 Pipe ends for ring seal or solvent cement
        joints
7 Classification and selection of pipes
   7.1 Classification
   7.2 Selection of the nominal pressure PN and of the
        pipe series S for water up to approximately 20
        degree C
   7.3 Determination of the allowable operating
        pressure PFA for water up to 45 degree C
8 Mechanical characteristics
   8.1 Impact strength
   8.2 Resistance to internal pressure
9 Physical characteristics
10 Chemical characteristics
11 Sealing rings
12 Adhesives
13 Performance requirements
14 Marking
   14.1 General
   14.2 Minimum required marking
   14.3 Additional marking
Annex A (normative) - Allowable operating pressures
Annex B (normative) - Imperial(inch)-sized pipes
Annex C (normative) - Requirements for fracture toughness
                      test
Annex D (informative) - Bibliography

Defines the characteristics of pipes made from unplasticized poly(vinyl chloride) (PVC-U) for piping systems in the field of water supply.

Committee
PRI/61/2
DevelopmentNote
Supersedes 94/341027 DC. Together with BS EN 1452-1, BS EN 1452-3, BS EN 1452-4 and BS EN 1452-5, it supersedes BS 3505(1986) and BS 4346-1(1969) which remains current & with BS EN 14814, BS EN 1452-1, BS EN 1452-3, BS EN 1452-4 and BS EN 1452-5, it supersedes BS 4346-3(1982). (08/2009) Together with BS EN 1452-1, BS EN 1452-3, BS EN 1452-4 and BS EN 1452-5, it supersedes BS 4346-2(1970) which remains current and inactive for the new design. (09/2009)
DocumentType
Standard
Pages
36
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
NF EN 1452-2 : 1999 Identical
EN 1452-2 : 1999 Identical
DIN EN 1452-2:1999-09 Identical
NBN EN 1452-2 : 2000 Identical
NEN EN 1452-2 : 1999 Identical
SN EN 1452-2 : 1999 Identical
I.S. EN 1452-2:1999 Identical
NS EN 1452-2 : 1999 Identical
UNI EN 1452-2 : 2001 Identical

BS EN 15014:2007 Plastics piping systems. Buried and above ground systems for water and other fluids under pressure. Performance characteristics for pipes, fittings and their joints
BS 8558:2015 Guide to the design, installation, testing and maintenance of services supplying water for domestic use within buildings and their curtilages. Complementary guidance to BS EN 806
BS 6700(2006) : 2006 DESIGN, INSTALLATION, TESTING AND MAINTENANCE OF SERVICES SUPPLYING WATER FOR DOMESTIC USE WITHIN BUILDINGS AND THEIR CURTILAGES - SPECIFICATION
EN 15014:2007 Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes, fittings and their joints

EN ISO 12162:2009 Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009)
EN 1452-5 : 1999 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
ENV 1452-6 : DRAFT 2001 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 6: GUIDANCE FOR INSTALLATION
EN 743 : 1994 PLASTICS PIPING AND DUCTING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF THE LONGITUDINAL REVERSION
ENV 1452-7:2000 Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 7: Guidance for the assessment of conformity
EN 578 : 1993 PLASTICS PIPING SYSTEMS - PLASTICS PIPES AND FITTINGS - DETERMINATION OF THE OPACITY
ISO 161-2:1996 Thermoplastics pipes for the conveyance of fluids — Nominal outside diameters and nominal pressures — Part 2: Inch-based series
ISO 1183:1987 Plastics Methods for determining the density and relative density of non-cellular plastics
ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
ISO 7387-1:1983 Adhesives with solvents for assembly of PVC-U pipe elements Characterization Part 1: Basic test methods
EN 921:1994/AC:1995 PLASTICS PIPING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF RESISTANCE TO INTERNAL PRESSURE AT CONSTANT TEMPERATURE
PREN 1796 : DRAFT 2011 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP)
EN 727:1994 Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST)
EN 744:1995 Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock method
ISO 6401:2008 Plastics — Poly(vinyl chloride) — Determination of residual vinyl chloride monomer — Gas-chromatographic method
EN 580:2003 Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for the resistance to dichloromethane at a specified temperature (DCMT)
ISO 4065:1996 Thermoplastics pipes Universal wall thickness table
EN 1452-1 : 1999 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: GENERAL
ISO/TR 9080:1992 Thermoplastics pipes for the transport of fluids — Methods of extrapolation of hydrostatic stress rupture data to determine the long-term hydrostatic strength of thermoplastics pipe materials

View more information
$427.45
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more