Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS EN 15502-2-1 : 2012

Current
Current

The latest, up-to-date edition.

GAS-FIRED CENTRAL HEATING BOILERS - PART 2-1: SPECIFIC STANDARD FOR TYPE C APPLIANCES AND TYPE B2, B3 AND B5 APPLIANCES OF A NOMINAL HEAT INPUT NOT EXCEEDING 1000 KW
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2012

European foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 Classification
5 Construction
6 Electrical safety
7 Controls
8 Operational requirements
9 Useful efficiencies
10 Electric auxiliary energy
11 Risk assessment
12 Marking and instructions
13 Requirements for Eco-design Regulation
   (No 813/2013) and Energy Labelling
   Regulation (No 811/2013)
101 Figures
102 Listing of tables and numbers
103 Annexes
Annex V (informative) - Standards replaced by this
        standard in combination with part 1
Annex XA (normative) - Test apparatus for type C[2] boilers
Annex XB (normative) - Test methods to determine the
         effects of long-term thermal load, long-term
         condensate exposure, condensing/non-condensing
         cycling and resistance to UV radiation
Annex XC (informative) - Variations in gas quality
Annex XD (informative) - Example on calculation of
         common duct system for type C[11] boilers
Annex ZB (informative) - Clauses of this European
         Standard addressing the methods for the
         verification of the efficiency of the EU
         Directive 92/42/EEC, relating to the
         efficiency of new hot boilers with an
         output of (4 - 400) kW
Annex ZC (informative) - Relationship between this
         European Standard and the Requirements of
         COMMISSION REGULATION (EU) No
         813/2013 of 2 August 2013 implementing
         Directive 2009/125/EC of the European
         Parliament and of the Council with regard
         to ecodesign requirements for space heaters
         and combination heaters
Annex ZD (informative) - Relationship between this
         European Standard and the Requirements of
         COMMISSION DELEGATED REGULATION
         (EU) No 811/2013 of 18 February 2013
         supplementing Directive 2010/30/EU of the
         European Parliament and of the Council with
         regard to the energy labelling of space heaters,
         combination heaters, packages of space heater,
         temperature control and solar device and
         packages of combination heater, temperature
         control and solar device
Bibliography

Defines the requirements and test methods concerning, in particular, the construction, safety, fitness for purpose, and rational use of energy, as well as the classification and marking of gas-fired central heating boilers that are fitted with atmospheric burners, fan assisted atmospheric burners or fully premixed burners, and are hereafter referred to as 'boilers'.

Committee
GSE/29
DevelopmentNote
Supersedes 10/30218935 DC. (11/2012) Together with BS EN 15502-1, it supersedes BS EN 483 & BS EN 15420. Together with BS EN 15502-1 & BS EN 15502-2-2 it supersedes BS EN 297, BS EN 625, BS EN 677 & BS EN 15417 which remains current and will be withdrawn on 31/07/2017.(09/2014) 2012 Edition Re-issued in January 2017 & incorporates AMD 1 2016. Supersedes 14/30294049 DC. (02/2017)
DocumentType
Standard
Pages
110
PublisherName
British Standards Institution
Status
Current
Supersedes

Standards Relationship
EN 15502-2-1:2012+A1:2016 Identical

EN 1859:2009+A1:2013 Chimneys - Metal chimneys - Test methods
EN 15502-1:2012+A1:2015 Gas-fired heating boilers - Part 1: General requirements and tests
EN 13384-2:2015 CHIMNEYS - THERMAL AND FLUID DYNAMIC CALCULATION METHODS - PART 2: CHIMNEYS SERVING MORE THAN ONE HEATING APPLIANCE
EN ISO 1183-3 : 1999 PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 3: GAS PYKNOMETER METHOD
ISO 7619-1:2010 Rubber, vulcanized or thermoplastic Determination of indentation hardness Part 1: Durometer method (Shore hardness)
EN ISO 8256:2004 Plastics - Determination of tensile-impact strength (ISO 8256:2004)
ISO 815-2:2014 Rubber, vulcanized or thermoplastic Determination of compression set Part 2: At low temperatures
EN 1856-2:2009 Chimneys - Requirements for metal chimneys - Part 2: Metal flue liners and connecting flue pipes
EN 14989-1:2007 Chimneys - Requirements and test methods for metal chimneys and material independent air supply ducts for roomsealed heating applications - Part 1: Vertical air/flue terminals for C6-type appliances
CEN/TS 16134:2011 Chimney terminals - General requirements and material independent test methods
ISO 815-1:2014 Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures
EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
EN 13216-1:2004 Chimneys - Test methods for system chimneys - Part 1: General test methods
ISO 188:2011 Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
EN ISO 178:2010/A1:2013 PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
ISO 8256:2004 Plastics — Determination of tensile-impact strength
2009/142/EC : 2009 DIRECTIVE 2009/142/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 30 NOVEMBER 2009 RELATING TO APPLIANCES BURNING GASEOUS FUELS (TEXT WITH EEA RELEVANCE)
EN ISO 527-1:2012 Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012)
EN ISO 179-1:2010 Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010)
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
EN 14241-1:2013 Chimneys - Elastomeric seals and elastomeric sealants - Material requirements and test methods - Part 1: Seals in flue liners
EN 437:2003+A1:2009 Test gases - Test pressures - Appliance categories
ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
CEN/TR 1749:2014 European scheme for the classification of gas appliances according to the method of evacuation of the combustion products (types)
ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
ISO 1183-3:1999 Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method
EN ISO 9969:2016 Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016)
ISO 6914:2013 Rubber, vulcanized or thermoplastic Determination of ageing characteristics by measurement of stress relaxation in tension
EN 14471:2013+A1:2015 CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS
ISO 179-1:2010 Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 7619-2:2010 Rubber, vulcanized or thermoplastic Determination of indentation hardness Part 2: IRHD pocket meter method
92/42/EEC : 1992 AMD 5 2013 COUNCIL DIRECTIVE 92/42/EEC OF 21 MAY 1992 ON EFFICIENCY REQUIREMENTS FOR NEW HOT-WATER BOILERS FIRED WITH LIQUID OR GASEOUS FUELS
ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
EN 1856-1:2009 Chimneys - Requirements for metal chimneys - Part 1: System chimney products
ISO 178:2010 Plastics Determination of flexural properties
ISO 9969:2016 Thermoplastics pipes Determination of ring stiffness
EN 513:1999 Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Determination of the resistance to artificial weathering
EN 573-1:2004 Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 1: Numerical designation system
EN ISO 1183-1:2012 Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012)
EN 15502-2-2:2014 Gas-fired central heating boilers - Part 2-2: Specific standard for type B1 appliances
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels
EN ISO 1183-2:2004 PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 2: DENSITY GRADIENT COLUMN METHOD
ISO 2781:2008 Rubber, vulcanized or thermoplastic Determination of density

View more information
$584.31
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more