Sanitary tapware. Extractable outlets for sink and basin mixers. General technical specification

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

31-01-2013

Publisher

British Standards Institution

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Designation
6 Marking
7 Materials
8 Dimensional Characteristics
9 Leaktightness Characteristics
10 Mechanical Characteristics
11 Hydraulic Characteristics
12 Backflow protection
13 Acoustic characteristics
14 Rotary connection
Annex A (informative) - Pressure take-off tee
Bibliography

Defines: - the dimensional, leaktightness, mechanical, hydraulic and acoustic characteristics with which extractable outlets with or without spray mode selector function need to comply; - the procedures for testing these characteristics.

This part of ISO 5167 specifies the geometry and method of use (installation and operating conditions) of orifice plates when they are inserted in a conduit running full to determine the flowrate of the fluid flowing in the conduit.

This part of ISO 5167 also provides background information for calculating the flowrate and is applicable in conjunction with the requirements given in ISO 5167-1.

This part of ISO 5167 is applicable to primary devices having an orifice plate used with flange pressure tappings, or with corner pressure tappings, or with D and D/2 pressure tappings. Other pressure tappings such as “vena contracta?? and pipe tappings have been used with orifice plates but are not covered by this part of ISO 5167. This part of ISO 5167 is applicable only to a flow which remains subsonic throughout the measuring section and where the fluid can be considered as single phase. It is not applicable to the measurement of pulsating flow. It does not cover the use of orifice plates in pipe sizes less than 50 mm or more than 1 000 mm, or for pipe Reynolds numbers below 5 000.

Committee	B/504/-/8
DevelopmentNote	Supersedes 10/30228907 DC. (01/2013)
DocumentType	Standard
Pages	32
PublisherName	British Standards Institution
Status	Current
Supersedes	10/30228907 DC : 0

Standards	Relationship
EN 16145:2012	Identical

ISO 3822-1:1999	Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 1: Method of measurement
EN 817:2008	Sanitary tapware - Mechanical mixing valves (PN 10) - General technical specifications
EN 1287:2017	Sanitary tapware - Low pressure thermostatic mixing valves - General technical specification
EN 16146:2012+A1:2014	Sanitary tapware - Extractable shower hoses for sanitary tapware for supply systems type 1 and type 2 - General technical specification
EN 1254-2:1998	Copper and copper alloys - Plumbing fittings - Part 2: Fittings with compression ends for use with copper tubes
ISO 3822-4:1997	Acoustics Laboratory tests on noise emission from appliances and equipment used in water supply installations Part 4: Mounting and operating conditions for special appliances
EN 1286:1999	Sanitary tapware - Low pressure mechanical mixing valves - General technical specification
EN 1717:2000	Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow
EN ISO 228-1:2003	Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
EN ISO 3822-4:1997	Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 4: Mounting and operating conditions for special appliances
EN ISO 5167-1:2003	Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003)
ISO 5167-1:2003	Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements
EN 200:2008	Sanitary tapware - Single taps and combination taps for water supply systems of type 1 and type 2 - General technical specification
EN ISO 3822-1:1999/A1:2008	ACOUSTICS - LABORATORY TESTS ON NOISE EMISSION FROM APPLIANCES AND EQUIPMENT USED IN WATER SUPPLY INSTALLATIONS - PART 1: METHOD OF MEASUREMENT
EN 1111:2017	Sanitary tapware - Thermostatic mixing valves (PN 10) - General technical specification
ISO 228-1:2000	Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
EN 248:2002	Sanitary tapware - General specification for electrodeposited coatings of Ni-Cr

View more information

$407.85

Including GST where applicable

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

Log into your Account

BS EN 16145:2012

Current

Table of Contents

Abstract

Scope

General Product Information

International Equivalents

Standards Referencing This Book

Category

Subcategory

Access your standards online with a subscription