Customer Support: 131 242

i2i Intertek.com
  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site
Dismiss alert
Please enter a keyword to search
Advanced search

BS EN 60034-18-41:2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Rotating electrical machines Partial discharge free electrical insulation systems (Type I) used in rotating electrical machines fed from voltage converters. Qualification and quality control tests
Available format(s)

Hardcopy , PDF

Superseded date

02-11-2019

Language(s)

English

Published date

30-06-2014

Publisher

British Standards Institution

INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Machine terminal voltages arising
   from converter operation
5 Electrical stresses in the insulation system
   of machine windings
6 Types of machine insulation
7 Stress categories for Type I insulation systems
   used in converter fed machines
8 Design qualification and type tests for Type I
   insulation systems
9 Test equipment
10 Qualification of the design of Type
   I insulation systems
11 Type test procedure for Type I
   insulation systems
12 Routine tests
13 Analysis, reporting and classification
Annex A (informative) - Derivation of
         possible terminal voltages in
         service for a converter-fed
         machine
Annex B (normative) - Derivation of test
         voltages for Type I insulation systems
Annex C (normative) - Derivation of
        allowable voltages in service
Bibliography
Annex ZA (normative) - Normative
         references to international
         publications with their
         corresponding European
         publications

Specifies criteria for assessing the insulation system of stator/rotor windings which are subjected to voltage-source pulse width-modulation (PMW) drives.

IEC 60034-18-41:2014 defines criteria for assessing the insulation system of stator/rotor windings which are subjected to voltage-source pulse-width-modulation drives. It applies to stator/rotor windings of single or polyphase AC machines with insulation systems for converter operation. It describes qualification tests and quality control (type and routine) tests on representative samples or on completed machines which verify fitness for operation with voltage source converters.

Committee
PEL/2
DevelopmentNote
Supersedes 10/30238620 DC. (06/2014)
DocumentType
Standard
Pages
46
PublisherName
British Standards Institution
Status
Superseded
Supersedes

Standards Relationship
IEC 60034-18-41:2014 Identical
EN 60034-18-41:2014 Identical

EN 60034-18-1:2010 Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines
CLC/TS 60034-27:2011 Rotating electrical machines - Part 27: Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines
EN 60034-18-21:2013 Rotating electrical machines - Part 18-21: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Thermal evaluation and classification
EN 60034-18-31 : 2012 ROTATING ELECTRICAL MACHINES - PART 18-31: FUNCTIONAL EVALUATION OF INSULATION SYSTEMS - TEST PROCEDURES FOR FORM-WOUND WINDINGS - THERMAL EVALUATION AND CLASSIFICATION OF INSULATION SYSTEMS USED IN ROTATING MACHINES (IEC 60034-18-31:2012)
IEC TS 60034-27:2006 Rotating electrical machines - Part 27: Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines
IEC TS 61934:2011 Electrical insulating materials and systems - Electrical measurement of partial discharges (PD) under short rise time and repetitive voltage impulses
IEC TS 60034-18-42:2008 Rotating electrical machines - Part 18-42: Qualification and acceptance tests for partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters
IEC TS 61800-8:2010 Adjustable speed electrical power drive systems - Part 8: Specification of voltage on the power interface
IEC 60172:2015 Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires
IEC 60034-18-1:2010 Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines
IEC TS 60034-25:2014 Rotating electrical machines - Part 25: AC electrical machines used in power drive systems - Application guide
EN 60172:2015 Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires
EN 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
IEC 60034-18-21:2012 Rotating electrical machines - Part 18-21: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Thermal evaluation and classification
CLC/TS 60034-25:2008 Rotating electrical machines - Part 25: Guidance for the design and performance of a.c. motors specifically designed for converter supply
CLC/TS 60034-18-42:2011 Rotating electrical machines - Part 18-42: Qualification and acceptance tests for partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters
IEC 60034-18-31:2012 Rotating electrical machines - Part 18-31: Functional evaluation of insulation systems - Test procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in rotating machines
IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests

View more information
$541.18
Including GST where applicable
AUD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more