We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS EN 60297-3-101 : 2004

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482,6 MM (19 IN) SERIES - PART 3-101: SUBRACKS AND ASSOCIATED PLUG-IN UNITS

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2004

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    INTRODUCTION
    1 Scope and object
    2 Normative references
    3 Terms and definitions
    4 Arrangement overview
    5 Subrack dimensions, front mounting area
    6 Subrack dimensions, rear mounting area
    7 Printed board type plug-in units, front mounted
    8 Box type plug-in units, front mounted
    9 Printed board type plug-in units, rear mounted
    10 Subrack and plug-in units with electromagnetic
       shielding provisions
    11 Plug-in units electrostatic discharge provisions
    12 Dimensions used in the figures
    Annex ZA (normative) Normative references to international
             publications with their corresponding European
             publications

    Abstract - (Show below) - (Hide below)

    Specifies dimensions which will ensure dimensional interchangeability of subracks and associated plug-in units. Connector related dimensions are limited to "inspection dimensions" only.

    General Product Information - (Show below) - (Hide below)

    Committee EPL/48/4
    Development Note Supersedes BS 5954-3(1985), BS EN 60297-5-100, BS EN 60297-5-102, BS EN 60297-5-103 and BS EN 60297-5-107. Together with BS EN 60297-3-102 supersedes BS EN 60297-4. (06/2008)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    HD 493.2 : 200S1 DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482.6 MM (19 IN) SERIES - CABINETS AND PITCHES OF RACK STRUCTURES
    IEC 61076-4-113:2002 Connectors for electronic equipment - Printed board connectors - Part 4-113: Detail specification for two-part connectors having 5 rows with a grid of 2,54 mm for printed boards and backplanes in bus applications
    IEC 60297-1:1986 Dimensions of mechanical structures of the 482.6 mm (19 in) series. Part 1: Panels and racks
    HD 493.1 : 200S1 DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482.6 MM (19 IN) SERIES - PANELS AND RACKS
    IEC 60249-2-1:1985 Base materials for printed circuits. Part 2: Specifications. Specification No. 1: Phenolic cellulose paper copper-clad laminated sheet, high electrical quality
    IEC 61587-3:2013 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 - Part 3: Electromagnetic shielding performance tests for cabinets and subracks
    IEC 61587-1:2016 Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation
    EN 61076-4-113 : 2003 CONNECTORS FOR ELECTRONIC EQUIPMENT - PRINTED BOARD CONNECTORS - PART 4-113: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS HAVING 5 ROWS WITH A GRID OF 2,54 MM FOR PRINTED BOARDS AND BACKPLANES IN BUS APPLICATIONS
    EN 61587-1:2017 MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - TESTS FOR IEC 60917 AND IEC 60297 SERIES - PART 1: ENVIRONMENTAL REQUIREMENTS, TEST SET-UP AND SAFETY ASPECTS FOR CABINETS, RACKS, SUBRACKS AND CHASSIS UNDER INDOOR CONDITION USE AND TRANSPORTATION
    IEC 60603-2:1995 Connectors for frequencies below 3 MHz for use with printed boards - Part 2: Detail specification for two-part connectors with assessed quality, for printed boards, for basic grid of 2,54 mm (0,1 in) with common mounting features
    EN 60603-2:1998/A1:2005 CONNECTORS FOR FREQUENCIES BELOW 3 MHZ FOR USE WITH PRINTED BOARDS - PART 2: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH ASSESSED QUALITY, FOR PRINTED BOARDS, FOR BASIC GRID OF 2,54 MM (0,1 IN) WITH COMMON MOUNTING FEATURES
    EN 61076-4-101 : 2001 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-101: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR TWO-PART CONNECTOR MODULES, HAVING A BASIC GRID OF 2,0 MM FOR PRINTED BOARDS AND BACKPLANES IN ACCORDANCE WITH IEC 60917 (IEC 61076-4-101:2001)
    EN 60249-2-1 : 1994 AMD 4 2000 BASE MATERIALS FOR PRINTED CIRCUITS - PART 2: SPECIFICATIONS - SPECIFICATION NO. 1: PHENOLIC CELLULOSE PAPER COPPER-CLAD LAMINATED SHEET - HIGH ELECTRICAL QUALITY
    IEC 61076-4-101:2001 Connectors for electronic equipment - Part 4-101: Printed board connectors with assessed quality - Detail specification for two-part connector modules, having a basic grid of 2,0 mm for printed boards and backplanes in accordance with IEC 60917
    IEC 60297-2:1982 Dimensions of mechanical structures of the 482.6 mm (19 in) series. Part 2: Cabinets and pitches of rack structures
    IEC 60917-1:1998+AMD1:2000 CSV Modular order for the development of mechanical structures for electronic equipment practices - Part 1: Generic standard
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective