We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS EN 62282-3-3 : 2008

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    FUEL CELL TECHNOLOGIES - PART 3-3: STATIONARY FUEL CELL POWER SYSTEMS - INSTALLATION

    Available format(s):  Hardcopy, PDF

    Superseded date:  30-11-2012

    Language(s):  English

    Published date:  01-01-2008

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 General safety requirements and strategy
    5 Siting considerations
       5.1 General siting
       5.2 Outdoor installations
       5.3 Indoor installations
            5.3.1 Large fuel cell power systems
            5.3.2 Small fuel cell power systems
       5.4 Rooftop installation
    6 Ventilation and exhaust
       6.1 General
       6.2 Ventilation
       6.3 Exhaust system
       6.4 Process purging and venting
    7 Fire protection and gas detection
       7.1 Fire protection and detection
            7.1.1 Site fire protection
            7.1.2 Combustible gas detection (indoor installations only)
       7.2 Fire prevention and emergency planning
    8 Interconnections with site interfaces
       8.1 General
       8.2 Connections to fuel supplies - General
       8.3 Fuel shut off and piping
       8.4 Connections to auxiliary media supply and media disposal
            8.4.1 Combustible auxiliary gases
            8.4.2 Non combustible or inert auxiliary gases
            8.4.3 Water
            8.4.4 Waste water disposal
            8.4.5 Discharge pipe
    9 Environmental requirements
    10 Approval tests
       10.1 Gas leakage
       10.2 Site specific shutdown devices
    11 Maintenance tests
    12 Documentation
       12.1 Markings and instructions
       12.2 Inspection checklist
       12.3 Installation manual
       12.4 User's information manual
       12.5 Maintenance manual
    Annex ZA (normative) Normative references to international
             publications with their corresponding European
             publications

    Abstract - (Show below) - (Hide below)

    Gives minimum safety requirements for the installation of indoor and outdoor stationary fuel cell power systems in compliance with IEC 62282-3-1.

    General Product Information - (Show below) - (Hide below)

    Committee GEL/105
    Development Note Supersedes 05/30089621 DC. (09/2008)
    Document Type Standard
    Publisher British Standards Institution
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60079-10:2002 Electrical apparatus for explosive gas atmospheres - Part 10: Classification of hazardous areas
    IEC 62282-3-1:2007 Fuel cell technologies - Part 3-1: Stationary fuel cell power systems - Safety
    IEC 61779-6:1999 Electrical apparatus for the detection and measurement of flammable gases - Part 6: Guide for the selection, installation, use and maintenance of apparatus for the detection and measurement of flammable gases
    EN 61779-4 : 2000 ELECTRICAL APPARATUS FOR THE DETECTION AND MEASUREMENT OF FLAMMABLE GASES - PART 4: PERFORMANCE REQUIREMENTS FOR GROUP 2 APPARATUS INDICATING A VOLUME FRACTION UP TO 100% LOWER EXPLOSIVE LIMIT
    EN 61511-3:2017 FUNCTIONAL SAFETY - SAFETY INSTRUMENTED SYSTEMS FOR THE PROCESS INDUSTRY SECTOR - PART 3: GUIDANCE FOR THE DETERMINATION OF THE REQUIRED SAFETY INTEGRITY LEVELS (IEC 61511-3:2016)
    IEC 61779-4 : 1.0 ELECTRICAL APPARATUS FOR THE DETECTION AND MEASUREMENT OF FLAMMABLE GASES - PART 4: PERFORMANCE REQUIREMENTS FOR GROUP 2 APPARATUS INDICATING UP TO 100 % LOWER EXPLOSIVE LIMIT
    IEC 61511-3:2016 Functional safety - Safety instrumented systems for the process industry sector - Part 3: Guidance for the determination of the required safety integrity levels
    ISO 14121:1999 Safety of machinery Principles of risk assessment
    EN 60079-10:2003 ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 10: CLASSIFICATION OF HAZARDOUS AREAS
    EN 62282-3-1 : 2007 FUEL CELL TECHNOLOGIES - PART 3-1: STATIONARY FUEL CELL POWER SYSTEMS - SAFETY
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective