Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS EN ISO 11403-3:2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Plastics. Acquisition and presentation of comparable multipoint data Environmental influences on properties
Available format(s)

Hardcopy , PDF

Superseded date

09-07-2021

Language(s)

English

Published date

30-09-2014

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Specimen preparation
5 Conditioning
6 Test requirements
7 Presentation of data
8 Precision
Annex A (informative) - Information relating to certain
        test requirements
Annex B (normative) - Chemicals for chemical resistance
        and environmental stress cracking resistance
        tests
Bibliography

Defines test procedures for the acquisition and presentation of multipoint data which demonstrate the behaviour of plastics under the following environments: - prolonged exposure to heat; - liquid chemicals; - environmental stress cracking under a constant tensile stress; and - artificial weathering.

This part of ISO11403 specifies test procedures for the acquisition and presentation of multipoint data which demonstrate the behaviour of plastics under the following environments: prolonged exposure to heat; liquid chemicals; environmental stress cracking under a constant tensile stress; artificial weathering. The tests are listed in order of increasing severity of the environment. By testing under the least severe environments first, it is possible to make informed judgements regarding whether tests under more severe conditions are worthwhile.

Committee
PRI/21
DevelopmentNote
Supersedes 95/122840 DC (02/2002)
DocumentType
Standard
Pages
26
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

ISO 10350-2:2011 Plastics Acquisition and presentation of comparable single-point data Part 2: Long-fibre-reinforced plastics
ISO 4892-1:2016 Plastics Methods of exposure to laboratory light sources Part 1: General guidance
ISO 2578:1993 Plastics Determination of time-temperature limits after prolonged exposure to heat
ISO 293:2004 Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 295:2004 Plastics — Compression moulding of test specimens of thermosetting materials
ISO 10350-1:2017 Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials
ISO 10724-1:1998 Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens
ISO 294-2:1996 Plastics Injection moulding of test specimens of thermoplastic materials Part 2: Small tensile bars
ISO 4892-3:2016 Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps
ISO 175:2010 Plastics Methods of test for the determination of the effects of immersion in liquid chemicals
ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
ISO 4892-4:2013 Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps
ISO 4892-2:2013 Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 2818:1994 Plastics — Preparation of test specimens by machining
ISO 11403-1:2014 Plastics Acquisition and presentation of comparable multipoint data Part 1: Mechanical properties
ISO 20753:2008 Plastics Test specimens
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
ISO 10724-2:1998 Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates

View more information
$407.85
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more