PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 3: FITTINGS

Amended by

BS EN ISO 15874-3:2013+A1:2018

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2013

Publisher

British Standards Institution

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviated terms
4 Material characteristics
5 General characteristics
6 Geometrical characteristics
7 Mechanical characteristics of plastics fittings
8 Physical and chemical characteristics of plastics
components
9 Sealing elements
10 Performance requirements
11 Marking
Bibliography

Defines the characteristics of fittings for polypropylene (PP) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems under design pressures and temperatures according to the class of application.

Committee	PRI/88/2
DevelopmentNote	Supersedes 98/122504 DC. (06/2004) Supersedes 10/30228356 DC. (03/2013) Reviewed and confirmed by BSI, November 2017. (11/2017)
DocumentType	Standard
Pages	48
PublisherName	British Standards Institution
Status	Current
Supersedes	BS EN ISO 15874-3:2003 98/122504 DC : DRAFT MAY 1998 10/30228356 DC : 0

Standards	Relationship
ONORM EN ISO 15874-3 : 2013	Identical
UNI EN ISO 15874-3 : 2013	Identical
EN ISO 15874-3:2013	Identical
NBN EN ISO 15874-3 : 2013	Identical
I.S. EN ISO 15874-3:2013	Identical
NEN EN ISO 15874-3 : 2013	Identical
SN EN ISO 15874-3:2013	Identical
DIN EN ISO 15874-3:2013-06	Identical
ISO 15874-3:2013	Identical
UNE-EN ISO 15874-3:2013	Identical
NS EN ISO 15874-3 : 2013	Identical
NF EN ISO 15874-3 : 2013	Identical
DIN EN ISO 15874-3:2004-03	Identical

EN 1254-3:1998	Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes
EN 681-1:1996/A3:2005	ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
ISO 1133-1:2011	Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
ISO 15874-1:2013	Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 1: General
ISO 1167-4:2007	Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
ISO 9080:2012	Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
EN 681-2:2000/A2:2005	ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 2: THERMOPLASTIC ELASTOMERS
ISO 15874-2:2013	Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 2: Pipes
ISO 3126:2005	Plastics piping systems Plastics components Determination of dimensions
ISO 1167-3:2007	Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components
CEN/TR 12108:2012	Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption
ISO 15874-5:2013	Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 5: Fitness for purpose of the system
ISO/TS 15874-7:2003	Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 7: Guidance for the assessment of conformity
EN 10226-1:2004	Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation
ISO 228-1:2000	Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
ISO 7686:2005	Plastics pipes and fittings — Determination of opacity
EN 10088-1:2014	Stainless steels - Part 1: List of stainless steels
ISO 1167-1:2006	Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method

View more information

$364.71

Including GST where applicable

Product format

I agree to the DRM document license rules apply against the PDF selection made.

Please confirm that you agree to the document license rules for this document.

I agree to the document license rules .

Please confirm that you agree to the document license rules for this document.

Access your standards online with a subscription

Features

Simple online access to standards, technical information and regulations.
Critical updates of standards and customisable alerts and notifications.
Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

Get in touch with us

Log into your Account

BS EN ISO 15874-3 : 2013

Current

Table of Contents

Abstract

General Product Information

International Equivalents

Standards Referencing This Book

Category

Subcategory

Access your standards online with a subscription