Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS EN ISO 3126:2005

Current
Current

The latest, up-to-date edition.

Plastics piping systems. Plastics components. Determination of dimensions
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

31-07-2006

Foreword
1 Scope
2 Normative references
3 Terms, definitions and symbols
  3.1 Terms and definitions
  3.2 Symbols
4 Measuring devices
  4.1 General requirements
  4.2 Instruments
5 Determination of dimensions
  5.1 General
  5.2 Wall thicknesses
  5.3 Diameters
  5.4 Out-of-roundness
  5.5 Pipe lengths
  5.6 End squareness of pipes and fittings
6 Determination of other geometrical characteristics
  related to fittings
  6.1 General
  6.2 Bends
  6.3 Branches
  6.4 Reducers
7 Flanges, loose flanges and collar
  7.1 General
  7.2 Outside diameter of the flange, loose flange and collar
  7.3 Bore diameter of the flange or collar
  7.4 Bolt hole diameter
  7.5 Bolt hole distribution
  7.6 Concentricity of bolt circle diameter
  7.7 Pitch circle diameter
  7.8 Shoulder diameter of flange and collar
  7.9 Flange and collar thickness
  7.10 Length of the flange and collar
8 Other measurements
Bibliography

Provides methods for measurement and/or determination of the dimensions of plastics pipes and fittings and the accuracy of the measurement. Specifies procedures for measuring angles, diameters, lengths, squareness and wall thicknesses for the purposes of checking conformity to geometric limits.

This document specifies methods for measurement and/or determination of the dimensions of plastics pipes and fittings and the accuracy of the measurement.

It specifies procedures for measuring angles, diameters, lengths, squareness and wall thicknesses for the purposes of checking conformity to geometric limits.

NOTE This document is using metric units. However the procedures and tolerances are applicable to other units by using appropriate conversion factors.

Committee
PRI/88/4
DevelopmentNote
Supersedes BS 2782-11.1101A(1981) & 99/121962 DC. (07/2006)
DocumentType
Standard
Pages
28
PublisherName
British Standards Institution
Status
Current
Supersedes

BS 8588:2017 Polyethylene pressure pipe with an aluminium barrier layer and associated fittings for potable water supply in contaminated land. Size 20 mm to 630 mm
BS 7291-2:2010 Thermoplastics pipe and fitting systems for hot and cold water for domestic purposes and heating installations in buildings Specification for polybutylene (PB) pipe and associated fittings
16/30340367 DC : 0 BS 8588 - POLYEPTRHEYSLSEUNREE PIPES WITH AN ALUMINIUM BARRIER LAYER AND ASSOCIATED FITTINGS FOR POTABLE WATER SUPPLY IN CONTAMINATED LAND - SIZE 20 MM TO 630 MM
BS 7291-3:2010 Thermoplastics pipe and fitting systems for hot and cold water for domestic purposes and heating installations in buildings Specification for crosslinked polyethylene (PE-X) pipes and associated fittings
BS 5391-1:2006 Acrylonitrile-butadiene-styrene (ABS) pressure pipe Specification
BS 5392-1:2006 Acrylonitrile-butadiene-styrene (ABS) fittings for use with ABS pressure pipe Specification
BS 7291-1:2010 Thermoplastics pipe and fitting systems for hot and cold water for domestic purposes and heating installations in buildings General requirements
09/30208674 DC : 0 BS 7291-1 - THERMOPLASTICS PIPE AND FITTING SYSTEMS FOR HOT AND COLD WATER FOR DOMESTIC PURPOSES AND HEATING INSTALLATIONS IN BUILDINGS - PART 1: GENERAL REQUIREMENTS
09/30208678 DC : 0 BS 7291-3 - THERMOPLASTICS PIPES AND ASSOCIATED FITTINGS FOR HOT AND COLD WATER FOR DOMESTIC PURPOSES AND HEATING INSTALLATIONS IN BUILDINGS - PART 3: SPECIFICATION FOR CROSS-LINKED POLYETHYLENE (PE-X) PIPES AND ASSOCIATED FITTINGS
09/30208676 DC : 0 BS 7291-2 - THERMOPLASTICS PIPES AND ASSOCIATED FITTINGS FOR HOT AND COLD WATER FOR DOMESTIC PURPOSES AND HEATING INSTALLATIONS IN BUILDINGS - PART 2: SPECIFICATION FOR POLYBUTYLENE (PB) PIPES AND ASSOCIATED FITTINGS

ISO 6507-1:2005 Metallic materials Vickers hardness test Part 1: Test method
ISO 3599:1976 Vernier callipers reading to 0,1 and 0,05 mm
ISO 3611:2010 Geometrical product specifications (GPS) — Dimensional measuring equipment: Micrometers for external measurements — Design and metrological characteristics
ISO/R 463:1965 Dial gauges reading in 0.01 mm, 0.001 in and 0.0001 in
ISO 3534-1:2006 Statistics — Vocabulary and symbols — Part 1: General statistical terms and terms used in probability

View more information
$407.85
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more