Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS EN ISO 5270:2012

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Pulps. Laboratory sheets. Determination of physical properties
Available format(s)

Hardcopy , PDF

Superseded date

12-09-2022

Language(s)

English

Published date

31-10-2012

Foreword
Introduction
1 Scope
2 Normative references
3 Principle
4 Apparatus
5 Trimmed laboratory sheets
6 Procedures for physical properties ("low grammage" sheets)
7 Procedures for physical properties ("high grammage" sheets)
8 Test report
Bibliography

Describes the relevant International Standards to be used for the determination of physical properties of laboratory sheets made of all kind of pulps.

This International Standard specifies the relevant International Standards to be used for the determination of physical properties of laboratory sheets made of all kind of pulps. It is applicable to laboratory sheets prepared in accordance with ISO5269-1, ISO5269-2 or ISO5269-3.

In this International Standard, it is left to the pulp producer and the pulp user to agree upon which properties are relevant to be tested. The results are, if applicable, reported in index form.

Committee
PAI/11
DevelopmentNote
Supersedes BS ISO 5270. (05/2000) Supersedes 96/126335 DC. (10/2005)
DocumentType
Standard
Pages
20
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

ISO 5269-1:2005 Pulps Preparation of laboratory sheets for physical testing Part 1: Conventional sheet-former method
ISO 2493-1:2010 Paper and board Determination of bending resistance Part 1: Constant rate of deflection
ISO 1974:2012 Paper — Determination of tearing resistance — Elmendorf method
ISO 5636-3:2013 Paper and board — Determination of air permeance (medium range) — Part 3: Bendtsen method
ISO 5636-4:2013 Paper and board — Determination of air permeance (medium range) — Part 4: Sheffield method
ISO 11476:2016 Paper and board Determination of CIE whiteness, C/2 (indoor illumination conditions)
ISO 1924-3:2005 Paper and board Determination of tensile properties Part 3: Constant rate of elongation method (100 mm/min)
ISO 7263:2011 Corrugating medium Determination of the flat crush resistance after laboratory fluting
ISO 5626:1993 Paper Determination of folding endurance
ISO 2493-2:2011 Paper and board Determination of bending resistance Part 2: Taber-type tester
ISO 2471:2008 Paper and board — Determination of opacity (paper backing) — Diffuse reflectance method
ISO 9895:2008 Paper and board — Compressive strength — Short-span test
ISO 15361:2000 Pulps Determination of zero-span tensile strength, wet or dry
ISO 2758:2014 Paper Determination of bursting strength
ISO 187:1990 Paper, board and pulps — Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples
ISO 5628:2012 Paper and board — Determination of bending stiffness — General principles for two-point, three-point and four-point methods
ISO 2470-1:2016 Paper, board and pulps Measurement of diffuse blue reflectance factor Part 1: Indoor daylight conditions (ISO brightness)
ISO 5636-5:2013 Paper and board — Determination of air permeance (medium range) — Part 5: Gurley method
ISO 1924-2:2008 Paper and board — Determination of tensile properties — Part 2: Constant rate of elongation method (20 mm/min)
ISO 11475:2017 Paper and board — Determination of CIE whiteness, D65/10 degrees (outdoor daylight)
ISO 536:2012 Paper and board Determination of grammage
ISO 12192:2011 Paper and board — Determination of compressive strength — Ring crush method
ISO 534:2011 Paper and board — Determination of thickness, density and specific volume
ISO 5269-3:2008 Pulps — Preparation of laboratory sheets for physical testing — Part 3: Conventional and Rapid-Köthen sheet formers using a closed water system
ISO 3688:1999 Pulps — Preparation of laboratory sheets for the measurement of diffuse blue reflectance factor (ISO brightness)
ISO 9416:2017 Paper — Determination of light scattering and absorption coefficients (using Kubelka-Munk theory)
ISO 15754:2009 Paper and board Determination of z-directional tensile strength
ISO 5269-2:2004 Pulps Preparation of laboratory sheets for physical testing Part 2: Rapid-Kthen method

View more information
$294.12
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more