Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS ISO 10366-2 : 94 AMD 10665

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PLASTICS - METHYL METHYLACRYLATE/ACRYLONITRILE/BUTADIENE/STYRENE (MABS) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
Superseded date

15-11-1999

Published date

23-11-2012

NO CONTENTS SECTION

Specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of MABS moulding and extrusion materials. BS AMD 10665 RENUMBERS THIS STANDARD

Committee
PRI/33
DevelopmentNote
Renumbered and superseded by BS EN ISO 10366-2 (02/2004)
DocumentType
Standard
PublisherName
British Standards Institution
Status
Superseded
SupersededBy

Standards Relationship
ISO 10366-2:2003 Identical

IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
ISO 4589-3:2017 Plastics — Determination of burning behaviour by oxygen index — Part 3: Elevated-temperature test
ISO 75-1:2013 Plastics Determination of temperature of deflection under load Part 1: General test method
ISO 1656:2014 Rubber, raw natural, and rubber latex, natural Determination of nitrogen content
ISO 293:2004 Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 3167:2014 Plastics Multipurpose test specimens
ISO 527-4:1997 Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
IEC 60250:1969 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths
ISO 294:1995 Plastics Injection moulding of test specimens of thermoplastic materials
ISO 8256:2004 Plastics — Determination of tensile-impact strength
ISO 4851:1979 Personal eye-protectors Ultra-violet filters Utilisation and transmittance requirements
ISO 10350:1993 Plastics Acquisition and presentation of comparable single-point data
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 1183:1987 Plastics Methods for determining the density and relative density of non-cellular plastics
IEC 60296:2012 RLV Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear
IEC 60093:1980 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
ISO 180:2000 Plastics Determination of Izod impact strength
ISO 1210:1992 Plastics — Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source
ISO 2561:2012 Plastics — Determination of residual styrene monomer in polystyrene (PS) and impact-resistant polystyrene (PS-I) by gas chromatography
ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
ISO 62:2008 Plastics Determination of water absorption
ISO 306:2013 Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 4589-2:2017 Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
ISO 179:1993 Plastics Determination of Charpy impact strength
ISO 2818:1994 Plastics — Preparation of test specimens by machining
ISO 899-1:2017 Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 178:2010 Plastics Determination of flexural properties
ISO 10366-1:2002 Plastics Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials Part 1: Designation system and basis for specifications
ISO 1133:2005 Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
IEC 61006:2004 Electrical insulating materials - Methods of test for the determination of the glass transition temperature
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more