Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

BS ISO 12151-3:2010

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Connections for hydraulic fluid power and general use. Hose fittings Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends
Available format(s)

Hardcopy , PDF

Superseded date

29-11-2021

Language(s)

English

Published date

31-07-2010

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Performance requirements
5 Designation of hose fittings
6 Design
7 Manufacture
8 Procurement information
9 Marking
10 Identification statement (reference to this part of
   ISO 12151)
Bibliography

Defines the general and dimensional requirements for the design and performance of flange hose fittings, made of carbon steel, for nominal hose inside diameters of 12,5 mm to 51 mm inclusive, in accordance with ISO 4397, for use with ports and clamps in accordance with ISO 6162-1 and ISO 6162-2.

This part of ISO12151 specifies the general and dimensional requirements for the design and performance of flange hose fittings, made of carbon steel, for nominal hose inside diameters of 12,5mm to 51mm inclusive, in accordance with ISO4397, for use with ports and clamps in accordance with ISO6162-1 and ISO6162-2. NOTE1 Materials other than carbon steel can be supplied as agreed between the manufacturer and user. NOTE2 For hose fittings used in hydraulic and pneumatic braking systems on road vehicles (as defined in the scope of ISO/TC22/SC2, Road vehicles), see ISO4038, ISO4039-1 and ISO4039-2. These hose fittings (see Figure1 for a typical example) are for use in hydraulic fluid power systems with hose that meets the requirements of the respective hose standards and in general applications with suitable hoses. Figure1 Typical example of hose fitting connection with ISO6162-1 or ISO6162-2 flange end Key 1 hose fitting 2 port, flanged head and clamp per ISO6162-1 or ISO6162-2 3 O-ring seal

Committee
MCE/18/-/4
DevelopmentNote
Supersedes 94/714848 DC. (07/2005) Supersedes 07/30163202 DC. (07/2010)
DocumentType
Standard
Pages
24
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
ISO 12151-3:2010 Identical

ISO 4039-1:1998 Road vehicles — Pneumatic braking systems — Part 1: Pipes, male fittings and tapped holes with facial sealing surface
ISO 3862:2017 Rubber hoses and hose assemblies Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids Specification
ISO 3949:2009 Plastics hoses and hose assemblies Textile-reinforced types for hydraulic applications Specification
ISO 5598:2008 Fluid power systems and components Vocabulary
ISO 6605:2017 Hydraulic fluid power — Test methods for hoses and hose assemblies
ISO 4397:2011 Fluid power connectors and associated components — Nominal outside diameters of tubes and nominal hose sizes
ISO 4039-2:1998 Road vehicles Pneumatic braking systems Part 2: Pipes, male fittings and holes with conical sealing surface
ISO 6162-2:2012 Hydraulic fluid power Flange connections with split or one-piece flange clamps and metric or inch screws Part 2: Flange connectors, ports and mounting surfaces for use at a pressure of 42 MPa (420 bar), DN 13 to DN 76
ISO 4038:1996 Road vehicles — Hydraulic braking systems — Simple flare pipes, tapped holes, male fittings and hose end fittings
ISO 4079:2017 Rubber hoses and hose assemblies Textile-reinforced hydraulic types for oil-based or water-based fluids Specification
ISO 6162-1:2012 Hydraulic fluid power — Flange connections with split or one-piece flange clamps and metric or inch screws — Part 1: Flange connectors, ports and mounting surfaces for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127
ISO 19879:2010 Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections
ISO 9227:2017 Corrosion tests in artificial atmospheres — Salt spray tests
ISO 1436:2017 Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types for oil-based or water-based fluids Specification

View more information
$407.85
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more