We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • BS ISO 22621-5 : 2010

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You have already added this standard to your Watchlist.
    Visit My Watchlist to view the full list.

    PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS FOR MAXIMUM OPERATING PRESSURES UP TO AND INCLUDING 2 MPA (20 BAR) - POLYAMIDE (PA) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2010

    Publisher:  British Standards Institution

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    Introduction
    1 Scope
    2 Normative references
    3 Terms, definitions, symbols and abbreviated terms
    4 Fitness for purpose
    5 Overall service (design) coefficient
    Annex A (normative) - Preparation of test assemblies by
                          butt fusion
    Annex B (normative) - Preparation of test assemblies by
                          electrofusion
    Annex C (normative) - Test methods for the assessment of
                          fitness for purpose of transition
                          fittings
    Annex D (normative) - Derating coefficients for operating
                          temperatures
    Bibliography

    Abstract - (Show below) - (Hide below)

    Describes the requirements of fitness for purpose of the polyamide (PA) piping system, intended to be buried and used for the supply of gaseous fuels at maximum operating pressures (MOP) up to and including 2 MPa (20 bar).

    General Product Information - (Show below) - (Hide below)

    Committee PRI/88/2
    Development Note Supersedes 09/30175820 DC. (05/2010)
    Document Type Standard
    Publisher British Standards Institution
    Status Current
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 22621-2:2007 Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) Polyamide (PA) Part 2: Pipes
    ISO 15439-3:2007 Plastics piping systems for the supply of gaseous fuels for maximum operating pressure up to and including 0,4 MPa (4 bar) Polyamide (PA) Part 3: Fittings
    ISO 13953:2001 Polyethylene (PE) pipes and fittings Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
    ISO 22621-3:2007 Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) Polyamide (PA) Part 3: Fittings
    ISO 1167-4:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
    ISO 12176-2:2008 Plastics pipes and fittings Equipment for fusion jointing polyethylene systems Part 2: Electrofusion
    ISO 6259-1:2015 Thermoplastics pipes Determination of tensile properties Part 1: General test method
    ISO 15439-2:2007 Plastics piping systems for the supply of gaseous fuels for maximum operating pressure up to and including 0,4 MPa (4 bar) Polyamide (PA) Part 2: Pipes
    ISO 13954:1997 Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
    ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
    ISO 13955:1997 Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
    ISO 22621-1:2007 Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) Polyamide (PA) Part 1: General
    ISO 15439-1:2007 Plastics piping systems for the supply of gaseous fuels for maximum operating pressure up to and including 0,4 MPa (4 bar) Polyamide (PA) Part 1: General
    ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective